|  | /* | 
|  | * ds1302.c - Support for the Dallas Semiconductor DS1302 Timekeeping Chip | 
|  | * | 
|  | * Rex G. Feany <rfeany@zumanetworks.com> | 
|  | * | 
|  | */ | 
|  |  | 
|  | #include <common.h> | 
|  | #include <command.h> | 
|  | #include <rtc.h> | 
|  |  | 
|  | #if defined(CONFIG_RTC_DS1302) && (CONFIG_COMMANDS & CFG_CMD_DATE) | 
|  |  | 
|  | /* GPP Pins */ | 
|  | #define DATA		0x200 | 
|  | #define SCLK		0x400 | 
|  | #define RST		0x800 | 
|  |  | 
|  | /* Happy Fun Defines(tm) */ | 
|  | #define RESET		rtc_go_low(RST), rtc_go_low(SCLK) | 
|  | #define N_RESET		rtc_go_high(RST), rtc_go_low(SCLK) | 
|  |  | 
|  | #define CLOCK_HIGH	rtc_go_high(SCLK) | 
|  | #define CLOCK_LOW	rtc_go_low(SCLK) | 
|  |  | 
|  | #define DATA_HIGH	rtc_go_high(DATA) | 
|  | #define DATA_LOW	rtc_go_low(DATA) | 
|  | #define DATA_READ	(GTREGREAD(GPP_VALUE) & DATA) | 
|  |  | 
|  | #undef RTC_DEBUG | 
|  |  | 
|  | #ifdef RTC_DEBUG | 
|  | #  define DPRINTF(x,args...)	printf("ds1302: " x , ##args) | 
|  | static inline void DUMP(const char *ptr, int num) | 
|  | { | 
|  | while (num--) printf("%x ", *ptr++); | 
|  | printf("]\n"); | 
|  | } | 
|  | #else | 
|  | #  define DPRINTF(x,args...) | 
|  | #  define DUMP(ptr, num) | 
|  | #endif | 
|  |  | 
|  | /* time data format for DS1302 */ | 
|  | struct ds1302_st | 
|  | { | 
|  | unsigned char CH:1;		/* clock halt 1=stop 0=start */ | 
|  | unsigned char sec10:3; | 
|  | unsigned char sec:4; | 
|  |  | 
|  | unsigned char zero0:1; | 
|  | unsigned char min10:3; | 
|  | unsigned char min:4; | 
|  |  | 
|  | unsigned char fmt:1;		/* 1=12 hour 0=24 hour */ | 
|  | unsigned char zero1:1; | 
|  | unsigned char hr10:2;	/* 10 (0-2) or am/pm (am/pm, 0-1) */ | 
|  | unsigned char hr:4; | 
|  |  | 
|  | unsigned char zero2:2; | 
|  | unsigned char date10:2; | 
|  | unsigned char date:4; | 
|  |  | 
|  | unsigned char zero3:3; | 
|  | unsigned char month10:1; | 
|  | unsigned char month:4; | 
|  |  | 
|  | unsigned char zero4:5; | 
|  | unsigned char day:3; 		/* day of week */ | 
|  |  | 
|  | unsigned char year10:4; | 
|  | unsigned char year:4; | 
|  |  | 
|  | unsigned char WP:1;		/* write protect 1=protect 0=unprot */ | 
|  | unsigned char zero5:7; | 
|  | }; | 
|  |  | 
|  | static int ds1302_initted=0; | 
|  |  | 
|  | /* Pin control */ | 
|  | static inline void | 
|  | rtc_go_high(unsigned int mask) | 
|  | { | 
|  | unsigned int f = GTREGREAD(GPP_VALUE) | mask; | 
|  |  | 
|  | GT_REG_WRITE(GPP_VALUE, f); | 
|  | } | 
|  |  | 
|  | static inline void | 
|  | rtc_go_low(unsigned int mask) | 
|  | { | 
|  | unsigned int f = GTREGREAD(GPP_VALUE) & ~mask; | 
|  |  | 
|  | GT_REG_WRITE(GPP_VALUE, f); | 
|  | } | 
|  |  | 
|  | static inline void | 
|  | rtc_go_input(unsigned int mask) | 
|  | { | 
|  | unsigned int f = GTREGREAD(GPP_IO_CONTROL) & ~mask; | 
|  |  | 
|  | GT_REG_WRITE(GPP_IO_CONTROL, f); | 
|  | } | 
|  |  | 
|  | static inline void | 
|  | rtc_go_output(unsigned int mask) | 
|  | { | 
|  | unsigned int f = GTREGREAD(GPP_IO_CONTROL) | mask; | 
|  |  | 
|  | GT_REG_WRITE(GPP_IO_CONTROL, f); | 
|  | } | 
|  |  | 
|  | /* Access data in RTC */ | 
|  |  | 
|  | static void | 
|  | write_byte(unsigned char b) | 
|  | { | 
|  | int i; | 
|  | unsigned char mask=1; | 
|  |  | 
|  | for(i=0;i<8;i++) { | 
|  | CLOCK_LOW;			/* Lower clock */ | 
|  | (b&mask)?DATA_HIGH:DATA_LOW;	/* set data */ | 
|  | udelay(1); | 
|  | CLOCK_HIGH;		/* latch data with rising clock */ | 
|  | udelay(1); | 
|  | mask=mask<<1; | 
|  | } | 
|  | } | 
|  |  | 
|  | static unsigned char | 
|  | read_byte(void) | 
|  | { | 
|  | int i; | 
|  | unsigned char mask=1; | 
|  | unsigned char b=0; | 
|  |  | 
|  | for(i=0;i<8;i++) { | 
|  | CLOCK_LOW; | 
|  | udelay(1); | 
|  | if (DATA_READ) b|=mask;	/* if this bit is high, set in b */ | 
|  | CLOCK_HIGH;		/* clock out next bit */ | 
|  | udelay(1); | 
|  | mask=mask<<1; | 
|  | } | 
|  | return b; | 
|  | } | 
|  |  | 
|  | static void | 
|  | read_ser_drv(unsigned char addr, unsigned char *buf, int count) | 
|  | { | 
|  | int i; | 
|  | #ifdef RTC_DEBUG | 
|  | char *foo = buf; | 
|  | #endif | 
|  |  | 
|  | DPRINTF("READ 0x%x bytes @ 0x%x [ ", count, addr); | 
|  |  | 
|  | addr|=1;	/* READ */ | 
|  | N_RESET; | 
|  | udelay(4); | 
|  | write_byte(addr); | 
|  | rtc_go_input(DATA); /* Put gpp pin into input mode */ | 
|  | udelay(1); | 
|  | for(i=0;i<count;i++) *(buf++)=read_byte(); | 
|  | RESET; | 
|  | rtc_go_output(DATA);/* Reset gpp for output */ | 
|  | udelay(4); | 
|  |  | 
|  | DUMP(foo, count); | 
|  | } | 
|  |  | 
|  | static void | 
|  | write_ser_drv(unsigned char addr, unsigned char *buf, int count) | 
|  | { | 
|  | int i; | 
|  |  | 
|  | DPRINTF("WRITE 0x%x bytes @ 0x%x [ ", count, addr); | 
|  | DUMP(buf, count); | 
|  |  | 
|  | addr&=~1;	/* WRITE */ | 
|  | N_RESET; | 
|  | udelay(4); | 
|  | write_byte(addr); | 
|  | for(i=0;i<count;i++) write_byte(*(buf++)); | 
|  | RESET; | 
|  | udelay(4); | 
|  |  | 
|  | } | 
|  |  | 
|  | void | 
|  | rtc_init(void) | 
|  | { | 
|  | struct ds1302_st bbclk; | 
|  | unsigned char b; | 
|  | int mod; | 
|  |  | 
|  | DPRINTF("init\n"); | 
|  |  | 
|  | rtc_go_output(DATA|SCLK|RST); | 
|  |  | 
|  | /* disable write protect */ | 
|  | b = 0; | 
|  | write_ser_drv(0x8e,&b,1); | 
|  |  | 
|  | /* enable trickle */ | 
|  | b = 0xa5;	/* 1010.0101 */ | 
|  | write_ser_drv(0x90,&b,1); | 
|  |  | 
|  | /* read burst */ | 
|  | read_ser_drv(0xbe, (unsigned char *)&bbclk, 8); | 
|  |  | 
|  | /* Sanity checks */ | 
|  | mod = 0; | 
|  | if (bbclk.CH) { | 
|  | printf("ds1302: Clock was halted, starting clock\n"); | 
|  | bbclk.CH=0; | 
|  | mod=1; | 
|  | } | 
|  |  | 
|  | if (bbclk.fmt) { | 
|  | printf("ds1302: Clock was in 12 hour mode, fixing\n"); | 
|  | bbclk.fmt=0; | 
|  | mod=1; | 
|  | } | 
|  |  | 
|  | if (bbclk.year>9) { | 
|  | printf("ds1302: Year was corrupted, fixing\n"); | 
|  | bbclk.year10=100;	/* 2000 - why not? ;) */ | 
|  | bbclk.year=0; | 
|  | mod=1; | 
|  | } | 
|  |  | 
|  | /* Write out the changes if needed */ | 
|  | if (mod) { | 
|  | /* enable write protect */ | 
|  | bbclk.WP = 1; | 
|  | write_ser_drv(0xbe,(unsigned char *)&bbclk,8); | 
|  | } else { | 
|  | /* Else just turn write protect on */ | 
|  | b = 0x80; | 
|  | write_ser_drv(0x8e,&b,1); | 
|  | } | 
|  | DPRINTF("init done\n"); | 
|  |  | 
|  | ds1302_initted=1; | 
|  | } | 
|  |  | 
|  | void | 
|  | rtc_reset(void) | 
|  | { | 
|  | if(!ds1302_initted) rtc_init(); | 
|  | /* TODO */ | 
|  | } | 
|  |  | 
|  | void | 
|  | rtc_get(struct rtc_time *tmp) | 
|  | { | 
|  | struct ds1302_st bbclk; | 
|  |  | 
|  | if(!ds1302_initted) rtc_init(); | 
|  |  | 
|  | read_ser_drv(0xbe,(unsigned char *)&bbclk, 8);      /* read burst */ | 
|  |  | 
|  | if (bbclk.CH) { | 
|  | printf("ds1302: rtc_get: Clock was halted, clock probably " | 
|  | "corrupt\n"); | 
|  | } | 
|  |  | 
|  | tmp->tm_sec=10*bbclk.sec10+bbclk.sec; | 
|  | tmp->tm_min=10*bbclk.min10+bbclk.min; | 
|  | tmp->tm_hour=10*bbclk.hr10+bbclk.hr; | 
|  | tmp->tm_wday=bbclk.day; | 
|  | tmp->tm_mday=10*bbclk.date10+bbclk.date; | 
|  | tmp->tm_mon=10*bbclk.month10+bbclk.month; | 
|  | tmp->tm_year=10*bbclk.year10+bbclk.year + 1900; | 
|  |  | 
|  | tmp->tm_yday = 0; | 
|  | tmp->tm_isdst= 0; | 
|  |  | 
|  | DPRINTF("Get DATE: %4d-%02d-%02d (wday=%d)  TIME: %2d:%02d:%02d\n", | 
|  | tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, | 
|  | tmp->tm_hour, tmp->tm_min, tmp->tm_sec ); | 
|  | } | 
|  |  | 
|  | void | 
|  | rtc_set(struct rtc_time *tmp) | 
|  | { | 
|  | struct ds1302_st bbclk; | 
|  | unsigned char b=0; | 
|  |  | 
|  | if(!ds1302_initted) rtc_init(); | 
|  |  | 
|  | DPRINTF("Set DATE: %4d-%02d-%02d (wday=%d)  TIME: %2d:%02d:%02d\n", | 
|  | tmp->tm_year, tmp->tm_mon, tmp->tm_mday, tmp->tm_wday, | 
|  | tmp->tm_hour, tmp->tm_min, tmp->tm_sec); | 
|  |  | 
|  | memset(&bbclk,0,sizeof(bbclk)); | 
|  | bbclk.CH=0; /* dont halt */ | 
|  | bbclk.WP=1; /* write protect when we're done */ | 
|  |  | 
|  | bbclk.sec10=tmp->tm_sec/10; | 
|  | bbclk.sec=tmp->tm_sec%10; | 
|  |  | 
|  | bbclk.min10=tmp->tm_min/10; | 
|  | bbclk.min=tmp->tm_min%10; | 
|  |  | 
|  | bbclk.hr10=tmp->tm_hour/10; | 
|  | bbclk.hr=tmp->tm_hour%10; | 
|  |  | 
|  | bbclk.day=tmp->tm_wday; | 
|  |  | 
|  | bbclk.date10=tmp->tm_mday/10; | 
|  | bbclk.date=tmp->tm_mday%10; | 
|  |  | 
|  | bbclk.month10=tmp->tm_mon/10; | 
|  | bbclk.month=tmp->tm_mon%10; | 
|  |  | 
|  | tmp->tm_year -= 1900; | 
|  | bbclk.year10=tmp->tm_year/10; | 
|  | bbclk.year=tmp->tm_year%10; | 
|  |  | 
|  | write_ser_drv(0x8e,&b,1);           /* disable write protect */ | 
|  | write_ser_drv(0xbe,(unsigned char *)&bbclk, 8);     /* write burst */ | 
|  | } | 
|  |  | 
|  | #endif |