blob: 19bf80ba7eb6195a57b8d91bde9e793567da7fd6 [file] [log] [blame]
/*
* (C) Copyright 2007-2008
* Stelian Pop <stelian@popies.net>
* Lead Tech Design <www.leadtechdesign.com>
*
* (C) Copyright 2013
* Bo Shen <voice.shen@atmel.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/io.h>
#include <asm/arch/hardware.h>
#include <asm/arch/at91_pit.h>
#include <asm/arch/at91_pmc.h>
#include <asm/arch/clk.h>
#include <div64.h>
#if !defined(CONFIG_AT91FAMILY)
# error You need to define CONFIG_AT91FAMILY in your board config!
#endif
DECLARE_GLOBAL_DATA_PTR;
/*
* We're using the SAMA5D3x PITC in 32 bit mode, by
* setting the 20 bit counter period to its maximum (0xfffff).
* (See the relevant data sheets to understand that this really works)
*
* We do also mimic the typical powerpc way of incrementing
* two 32 bit registers called tbl and tbu.
*
* Those registers increment at 1/16 the main clock rate.
*/
#define TIMER_LOAD_VAL 0xfffff
static inline unsigned long long tick_to_time(unsigned long long tick)
{
tick *= CONFIG_SYS_HZ;
do_div(tick, gd->arch.timer_rate_hz);
return tick;
}
static inline unsigned long long usec_to_tick(unsigned long long usec)
{
usec *= gd->arch.timer_rate_hz;
do_div(usec, 1000000);
return usec;
}
/*
* Use the PITC in full 32 bit incrementing mode
*/
int timer_init(void)
{
at91_pit_t *pit = (at91_pit_t *)ATMEL_BASE_PIT;
/* Enable PITC Clock */
at91_periph_clk_enable(ATMEL_ID_PIT);
/* Enable PITC */
writel(TIMER_LOAD_VAL | AT91_PIT_MR_EN , &pit->mr);
gd->arch.timer_rate_hz = get_pit_clk_rate() / 16;
gd->arch.tbu = 0;
gd->arch.tbl = 0;
return 0;
}
/*
* Get the current 64 bit timer tick count
*/
unsigned long long get_ticks(void)
{
at91_pit_t *pit = (at91_pit_t *)ATMEL_BASE_PIT;
ulong now = readl(&pit->piir);
/* increment tbu if tbl has rolled over */
if (now < gd->arch.tbl)
gd->arch.tbu++;
gd->arch.tbl = now;
return (((unsigned long long)gd->arch.tbu) << 32) | gd->arch.tbl;
}
void __udelay(unsigned long usec)
{
unsigned long long start;
ulong tmo;
start = get_ticks(); /* get current timestamp */
tmo = usec_to_tick(usec); /* convert usecs to ticks */
while ((get_ticks() - start) < tmo)
; /* loop till time has passed */
}
/*
* get_timer(base) can be used to check for timeouts or
* to measure elasped time relative to an event:
*
* ulong start_time = get_timer(0) sets start_time to the current
* time value.
* get_timer(start_time) returns the time elapsed since then.
*
* The time is used in CONFIG_SYS_HZ units!
*/
ulong get_timer(ulong base)
{
return tick_to_time(get_ticks()) - base;
}
/*
* Return the number of timer ticks per second.
*/
ulong get_tbclk(void)
{
return gd->arch.timer_rate_hz;
}