blob: 709cf231d01ba7d4e5dd5bbf7064214deb7d921f [file] [log] [blame] [edit]
; General settings that can be overwritten in the host code
; that calls the AISGen library.
[General]
; Can be 8 or 16 - used in emifa
busWidth=8
; SPIMASTER,I2CMASTER,EMIFA,NAND,EMAC,UART,PCI,HPI,USB,MMC_SD,VLYNQ,RAW
BootMode=UART
; 8,16,24 - used for SPI,I2C
;AddrWidth=8
; NO_CRC,SECTION_CRC,SINGLE_CRC
crcCheckType=NO_CRC
; This section allows setting the PLL0 system clock with a
; specified multiplier and divider as shown. The clock source
; can also be chosen for internal or external.
; |------24|------16|-------8|-------0|
; PLL0CFG0: | CLKMODE| PLLM | PREDIV | POSTDIV|
; PLL0CFG1: | RSVD | PLLDIV1| PLLDIV3| PLLDIV7|
;[PLL0CONFIG]
;PLL0CFG0 = 0x00180001
;PLL0CFG1 = 0x00000205
[PLLANDCLOCKCONFIG]
PLL0CFG0 = 0x00180001
PLL0CFG1 = 0x00000205
PERIPHCLKCFG = 0x00000051
; This section allows setting up the PLL1. Usually this will
; take place as part of the EMIF3a DDR setup. The format of
; the input args is as follows:
; |------24|------16|-------8|-------0|
; PLL1CFG0: | PLLM| POSTDIV| PLLDIV1| PLLDIV2|
; PLL1CFG1: | RSVD | PLLDIV3|
[PLL1CONFIG]
PLL1CFG0 = 0x18010001
PLL1CFG1 = 0x00000002
; This section lets us configure the peripheral interface
; of the current booting peripheral (I2C, SPI, or UART).
; Use with caution. The format of the PERIPHCLKCFG field
; is as follows:
; SPI: |------24|------16|-------8|-------0|
; | RSVD |PRESCALE|
;
; I2C: |------24|------16|-------8|-------0|
; | RSVD |PRESCALE| CLKL | CLKH |
;
; UART: |------24|------16|-------8|-------0|
; | RSVD | OSR | DLH | DLL |
[PERIPHCLKCFG]
PERIPHCLKCFG = 0x00000051
; This section can be used to configure the PLL1 and the EMIF3a registers
; for starting the DDR2 interface.
; See PLL1CONFIG section for the format of the PLL1CFG fields.
; |------24|------16|-------8|-------0|
; PLL1CFG0: | PLL1CFG |
; PLL1CFG1: | PLL1CFG |
; DDRPHYC1R: | DDRPHYC1R |
; SDCR: | SDCR |
; SDTIMR: | SDTIMR |
; SDTIMR2: | SDTIMR2 |
; SDRCR: | SDRCR |
; CLK2XSRC: | CLK2XSRC |
[EMIF3DDR]
PLL1CFG0 = 0x18010001
PLL1CFG1 = 0x00000002
DDRPHYC1R = 0x000000C2
SDCR = 0x0017C432
SDTIMR = 0x26922A09
SDTIMR2 = 0x4414C722
SDRCR = 0x00000498
CLK2XSRC = 0x00000000
; This section can be used to configure the EMIFA to use
; CS0 as an SDRAM interface. The fields required to do this
; are given below.
; |------24|------16|-------8|-------0|
; SDBCR: | SDBCR |
; SDTIMR: | SDTIMR |
; SDRSRPDEXIT: | SDRSRPDEXIT |
; SDRCR: | SDRCR |
; DIV4p5_CLK_ENABLE: | DIV4p5_CLK_ENABLE |
;[EMIF25SDRAM]
;SDBCR = 0x00004421
;SDTIMR = 0x42215810
;SDRSRPDEXIT = 0x00000009
;SDRCR = 0x00000410
;DIV4p5_CLK_ENABLE = 0x00000001
; This section can be used to configure the async chip selects
; of the EMIFA (CS2-CS5). The fields required to do this
; are given below.
; |------24|------16|-------8|-------0|
; A1CR: | A1CR |
; A2CR: | A2CR |
; A3CR: | A3CR |
; A4CR: | A4CR |
; NANDFCR: | NANDFCR |
;[EMIF25ASYNC]
;A1CR = 0x00000000
;A2CR = 0x00000000
;A3CR = 0x00000000
;A4CR = 0x00000000
;NANDFCR = 0x00000000
[EMIF25ASYNC]
A1CR = 0x00000000
A2CR = 0x04202110
A3CR = 0x00000000
A4CR = 0x00000000
NANDFCR = 0x00000012
; This section should be used in place of PLL0CONFIG when
; the I2C, SPI, or UART modes are being used. This ensures that
; the system PLL and the peripheral's clocks are changed together.
; See PLL0CONFIG section for the format of the PLL0CFG fields.
; See PERIPHCLKCFG section for the format of the CLKCFG field.
; |------24|------16|-------8|-------0|
; PLL0CFG0: | PLL0CFG |
; PLL0CFG1: | PLL0CFG |
; PERIPHCLKCFG: | CLKCFG |
;[PLLANDCLOCKCONFIG]
;PLL0CFG0 = 0x00180001
;PLL0CFG1 = 0x00000205
;PERIPHCLKCFG = 0x00010032
; This section should be used to setup the power state of modules
; of the two PSCs. This section can be included multiple times to
; allow the configuration of any or all of the device modules.
; |------24|------16|-------8|-------0|
; LPSCCFG: | PSCNUM | MODULE | PD | STATE |
;[PSCCONFIG]
;LPSCCFG=
; This section allows setting of a single PINMUX register.
; This section can be included multiple times to allow setting
; as many PINMUX registers as needed.
; |------24|------16|-------8|-------0|
; REGNUM: | regNum |
; MASK: | mask |
; VALUE: | value |
;[PINMUX]
;REGNUM = 5
;MASK = 0x00FF0000
;VALUE = 0x00880000
; No Params required - simply include this section for the fast boot
; function to be called
;[FASTBOOT]
; This section allows setting up the PLL1. Usually this will
; take place as part of the EMIF3a DDR setup. The format of
; the input args is as follows:
; |------24|------16|-------8|-------0|
; PLL1CFG0: | PLLM| POSTDIV| PLLDIV1| PLLDIV2|
; PLL1CFG1: | RSVD | PLLDIV3|
;[PLL1CONFIG]
;PLL1CFG0 = 0x15010001
;PLL1CFG1 = 0x00000002
; This section can be used to configure the PLL1 and the EMIF3a registers
; for starting the DDR2 interface on ARM-boot D800K002 devices.
; |------24|------16|-------8|-------0|
; DDRPHYC1R: | DDRPHYC1R |
; SDCR: | SDCR |
; SDTIMR: | SDTIMR |
; SDTIMR2: | SDTIMR2 |
; SDRCR: | SDRCR |
; CLK2XSRC: | CLK2XSRC |
;[ARM_EMIF3DDR_PATCHFXN]
;DDRPHYC1R = 0x000000C2
;SDCR = 0x0017C432
;SDTIMR = 0x26922A09
;SDTIMR2 = 0x4414C722
;SDRCR = 0x00000498
;CLK2XSRC = 0x00000000
; This section can be used to configure the PLL1 and the EMIF3a registers
; for starting the DDR2 interface on DSP-boot D800K002 devices.
; |------24|------16|-------8|-------0|
; DDRPHYC1R: | DDRPHYC1R |
; SDCR: | SDCR |
; SDTIMR: | SDTIMR |
; SDTIMR2: | SDTIMR2 |
; SDRCR: | SDRCR |
; CLK2XSRC: | CLK2XSRC |
;[DSP_EMIF3DDR_PATCHFXN]
;DDRPHYC1R = 0x000000C4
;SDCR = 0x08134632
;SDTIMR = 0x26922A09
;SDTIMR2 = 0x0014C722
;SDRCR = 0x00000492
;CLK2XSRC = 0x00000000
;[INPUTFILE]
;FILENAME=u-boot.bin
;LOADADDRESS=0xC1080000
;ENTRYPOINTADDRESS=0xC1080000