blob: 71d16e480d0c11227036eeafda736924ba3a1a8d [file] [log] [blame] [edit]
/*
* (C) Copyright 2001-2003
* Stefan Roese, esd gmbh germany, stefan.roese@esd-electronics.com
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/processor.h>
#include <command.h>
#include <malloc.h>
/* ------------------------------------------------------------------------- */
#if 0
#define FPGA_DEBUG
#endif
/* fpga configuration data - gzip compressed and generated by bin2c */
const unsigned char fpgadata[] =
{
#include "fpgadata.c"
};
/*
* include common fpga code (for esd boards)
*/
#include "../common/fpga.c"
int board_early_init_f (void)
{
/*
* IRQ 0-15 405GP internally generated; active high; level sensitive
* IRQ 16 405GP internally generated; active low; level sensitive
* IRQ 17-24 RESERVED
* IRQ 25 (EXT IRQ 0) CAN0; active low; level sensitive
* IRQ 26 (EXT IRQ 1) SER0 ; active low; level sensitive
* IRQ 27 (EXT IRQ 2) SER1; active low; level sensitive
* IRQ 28 (EXT IRQ 3) FPGA 0; active low; level sensitive
* IRQ 29 (EXT IRQ 4) FPGA 1; active low; level sensitive
* IRQ 30 (EXT IRQ 5) PCI INTA; active low; level sensitive
* IRQ 31 (EXT IRQ 6) COMPACT FLASH; active high; level sensitive
*/
mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
mtdcr(UIC0ER, 0x00000000); /* disable all ints */
mtdcr(UIC0CR, 0x00000000); /* set all to be non-critical*/
mtdcr(UIC0PR, 0xFFFFFF9F); /* set int polarities */
mtdcr(UIC0TR, 0x10000000); /* set int trigger levels */
mtdcr(UIC0VCR, 0x00000001); /* set vect base=0,INT0 highest priority*/
mtdcr(UIC0SR, 0xFFFFFFFF); /* clear all ints */
/*
* EBC Configuration Register: set ready timeout to 512 ebc-clks -> ca. 15 us
*/
mtebc (EBC0_CFG, 0xa8400000); /* ebc always driven */
return 0;
}
int misc_init_r (void)
{
unsigned char *dst;
ulong len = sizeof(fpgadata);
int status;
int index;
int i;
dst = malloc(CONFIG_SYS_FPGA_MAX_SIZE);
if (gunzip (dst, CONFIG_SYS_FPGA_MAX_SIZE, (uchar *)fpgadata, &len) != 0) {
printf ("GUNZIP ERROR - must RESET board to recover\n");
do_reset (NULL, 0, 0, NULL);
}
status = fpga_boot(dst, len);
if (status != 0) {
printf("\nFPGA: Booting failed ");
switch (status) {
case ERROR_FPGA_PRG_INIT_LOW:
printf("(Timeout: INIT not low after asserting PROGRAM*)\n ");
break;
case ERROR_FPGA_PRG_INIT_HIGH:
printf("(Timeout: INIT not high after deasserting PROGRAM*)\n ");
break;
case ERROR_FPGA_PRG_DONE:
printf("(Timeout: DONE not high after programming FPGA)\n ");
break;
}
/* display infos on fpgaimage */
index = 15;
for (i=0; i<4; i++) {
len = dst[index];
printf("FPGA: %s\n", &(dst[index+1]));
index += len+3;
}
putc ('\n');
/* delayed reboot */
for (i=20; i>0; i--) {
printf("Rebooting in %2d seconds \r",i);
for (index=0;index<1000;index++)
udelay(1000);
}
putc ('\n');
do_reset(NULL, 0, 0, NULL);
}
puts("FPGA: ");
/* display infos on fpgaimage */
index = 15;
for (i=0; i<4; i++) {
len = dst[index];
printf("%s ", &(dst[index+1]));
index += len+3;
}
putc ('\n');
free(dst);
/*
* Reset FPGA via FPGA_DATA pin
*/
SET_FPGA(FPGA_PRG | FPGA_CLK);
udelay(1000); /* wait 1ms */
SET_FPGA(FPGA_PRG | FPGA_CLK | FPGA_DATA);
udelay(1000); /* wait 1ms */
/*
* Reset external DUARTs
*/
out_be32((void *)GPIO0_OR,
in_be32((void *)GPIO0_OR) | CONFIG_SYS_DUART_RST);
udelay(10); /* wait 10us */
out_be32((void *)GPIO0_OR,
in_be32((void *)GPIO0_OR) & ~CONFIG_SYS_DUART_RST);
udelay(1000); /* wait 1ms */
/*
* Enable interrupts in exar duart mcr[3]
*/
out_8((void *)(DUART0_BA + 4), 0x08);
out_8((void *)(DUART1_BA + 4), 0x08);
out_8((void *)(DUART2_BA + 4), 0x08);
out_8((void *)(DUART3_BA + 4), 0x08);
return (0);
}
/*
* Check Board Identity:
*/
int checkboard (void)
{
char str[64];
int i = getenv_f("serial#", str, sizeof(str));
puts ("Board: ");
if (i == -1) {
puts ("### No HW ID - assuming WUH405");
} else {
puts(str);
}
putc ('\n');
return 0;
}