blob: ee9b7a9d3e56351f54fe722cdb5c597e63405f4b [file] [log] [blame]
/*
* Memory Setup stuff - taken from blob memsetup.S
*
* Copyright (C) 1999 2000 2001 Erik Mouw (J.A.K.Mouw@its.tudelft.nl) and
* Jan-Derk Bakker (J.D.Bakker@its.tudelft.nl)
*
* Modified for MPL VCMA9 by
* David Mueller, ELSOFT AG, <d.mueller@elsoft.ch>
* (C) Copyright 2002, 2003, 2004, 2005
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <config.h>
#include <version.h>
/* register definitions */
#define PLD_BASE 0x28000000
#define MISC_REG 0x103
#define SDRAM_REG 0x106
#define BWSCON 0x48000000
#define CLKBASE 0x4C000000
#define LOCKTIME 0x0
#define MPLLCON 0x4
#define UPLLCON 0x8
#define GPIOBASE 0x56000000
#define GSTATUS1 0xB0
#define FASTCPU 0x02
/* some parameters for the board */
/* BWSCON */
#define DW8 (0x0)
#define DW16 (0x1)
#define DW32 (0x2)
#define WAIT (0x1<<2)
#define UBLB (0x1<<3)
/* BANKSIZE */
#define BURST_EN (0x1<<7)
/* BANK0CON 200 */
#define B0_Tacs_200 0x0 /* 0clk (or 0x1 1clk) */
#define B0_Tcos_200 0x1 /* 1clk (or 0x2 2clk) */
#define B0_Tacc_200 0x5 /* 8clk (or 0x6 10clk) */
#define B0_Tcoh_200 0x0 /* 0clk */
#define B0_Tcah_200 0x3 /* 4clk (or0x01 1clk) */
#define B0_Tacp_200 0x0 /* page mode is not used */
#define B0_PMC_200 0x0 /* page mode disabled */
/* BANK0CON 250 */
#define B0_Tacs_250 0x0 /* 0clk (or 0x1 1clk) */
#define B0_Tcos_250 0x1 /* 1clk (or 0x2 2clk) */
#define B0_Tacc_250 0x5 /* 8clk (or 0x7 14clk) */
#define B0_Tcoh_250 0x0 /* 0clk */
#define B0_Tcah_250 0x3 /* 4clk (or 0x1 1clk) */
#define B0_Tacp_250 0x0 /* page mode is not used */
#define B0_PMC_250 0x0 /* page mode disabled */
/* BANK0CON 266 */
#define B0_Tacs_266 0x0 /* 0clk (or 0x1 1clk) */
#define B0_Tcos_266 0x1 /* 1clk (or 0x2 2clk) */
#define B0_Tacc_266 0x6 /* 10clk (or 0x7 14clk) */
#define B0_Tcoh_266 0x0 /* 0clk */
#define B0_Tcah_266 0x3 /* 4clk (or 0x1 1clk) */
#define B0_Tacp_266 0x0 /* page mode is not used */
#define B0_PMC_266 0x0 /* page mode disabled */
/* BANK1CON 200 */
#define B1_Tacs_200 0x0 /* 0clk (or 0x1 1clk) */
#define B1_Tcos_200 0x1 /* 1clk (or 0x2 2clk) */
#define B1_Tacc_200 0x5 /* 8clk (or 0x6 10clk) */
#define B1_Tcoh_200 0x0 /* 0clk */
#define B1_Tcah_200 0x3 /* 4clk (or 0x1 1clk) */
#define B1_Tacp_200 0x0 /* page mode is not used */
#define B1_PMC_200 0x0 /* page mode disabled */
/* BANK1CON 250 */
#define B1_Tacs_250 0x0 /* 0clk (or 0x1 1clk) */
#define B1_Tcos_250 0x1 /* 1clk (or 0x2 2clk) */
#define B1_Tacc_250 0x5 /* 8clk (or 0x7 14clk) */
#define B1_Tcoh_250 0x0 /* 0clk */
#define B1_Tcah_250 0x3 /* 4clk (or 0x1 1clk) */
#define B1_Tacp_250 0x0 /* page mode is not used */
#define B1_PMC_250 0x0 /* page mode disabled */
/* BANK1CON 266 */
#define B1_Tacs_266 0x0 /* 0clk (or 0x1 1clk) */
#define B1_Tcos_266 0x1 /* 1clk (or 0x2 2clk) */
#define B1_Tacc_266 0x6 /* 10clk (or 0x7 14clk) */
#define B1_Tcoh_266 0x0 /* 0clk */
#define B1_Tcah_266 0x3 /* 4clk (or 0x1 1clk) */
#define B1_Tacp_266 0x0 /* page mode is not used */
#define B1_PMC_266 0x0 /* page mode disabled */
/* BANK2CON 200 + 250 + 266 */
#define B2_Tacs 0x3 /* 4clk */
#define B2_Tcos 0x3 /* 4clk */
#define B2_Tacc 0x7 /* 14clk */
#define B2_Tcoh 0x3 /* 4clk */
#define B2_Tcah 0x3 /* 4clk */
#define B2_Tacp 0x0 /* page mode is not used */
#define B2_PMC 0x0 /* page mode disabled */
/* BANK3CON 200 + 250 + 266 */
#define B3_Tacs 0x3 /* 4clk */
#define B3_Tcos 0x3 /* 4clk */
#define B3_Tacc 0x7 /* 14clk */
#define B3_Tcoh 0x3 /* 4clk */
#define B3_Tcah 0x3 /* 4clk */
#define B3_Tacp 0x0 /* page mode is not used */
#define B3_PMC 0x0 /* page mode disabled */
/* BANK4CON 200 */
#define B4_Tacs_200 0x1 /* 1clk */
#define B4_Tcos_200 0x3 /* 4clk */
#define B4_Tacc_200 0x7 /* 14clk */
#define B4_Tcoh_200 0x3 /* 4clk */
#define B4_Tcah_200 0x2 /* 2clk */
#define B4_Tacp_200 0x0 /* page mode is not used */
#define B4_PMC_200 0x0 /* page mode disabled */
/* BANK4CON 250 */
#define B4_Tacs_250 0x1 /* 1clk */
#define B4_Tcos_250 0x3 /* 4clk */
#define B4_Tacc_250 0x7 /* 14clk */
#define B4_Tcoh_250 0x3 /* 4clk */
#define B4_Tcah_250 0x2 /* 2clk */
#define B4_Tacp_250 0x0 /* page mode is not used */
#define B4_PMC_250 0x0 /* page mode disabled */
/* BANK4CON 266 */
#define B4_Tacs_266 0x1 /* 1clk */
#define B4_Tcos_266 0x3 /* 4clk */
#define B4_Tacc_266 0x7 /* 14clk */
#define B4_Tcoh_266 0x3 /* 4clk */
#define B4_Tcah_266 0x2 /* 2clk */
#define B4_Tacp_266 0x0 /* page mode is not used */
#define B4_PMC_266 0x0 /* page mode disabled */
/* BANK5CON 200 */
#define B5_Tacs_200 0x0 /* 0clk */
#define B5_Tcos_200 0x3 /* 4clk */
#define B5_Tacc_200 0x4 /* 6clk */
#define B5_Tcoh_200 0x3 /* 4clk */
#define B5_Tcah_200 0x1 /* 1clk */
#define B5_Tacp_200 0x0 /* page mode is not used */
#define B5_PMC_200 0x0 /* page mode disabled */
/* BANK5CON 250 */
#define B5_Tacs_250 0x0 /* 0clk */
#define B5_Tcos_250 0x3 /* 4clk */
#define B5_Tacc_250 0x5 /* 8clk */
#define B5_Tcoh_250 0x3 /* 4clk */
#define B5_Tcah_250 0x1 /* 1clk */
#define B5_Tacp_250 0x0 /* page mode is not used */
#define B5_PMC_250 0x0 /* page mode disabled */
/* BANK5CON 266 */
#define B5_Tacs_266 0x0 /* 0clk */
#define B5_Tcos_266 0x3 /* 4clk */
#define B5_Tacc_266 0x5 /* 8clk */
#define B5_Tcoh_266 0x3 /* 4clk */
#define B5_Tcah_266 0x1 /* 1clk */
#define B5_Tacp_266 0x0 /* page mode is not used */
#define B5_PMC_266 0x0 /* page mode disabled */
#define B6_MT 0x3 /* SDRAM */
#define B6_Trcd_200 0x0 /* 2clk */
#define B6_Trcd_250 0x1 /* 3clk */
#define B6_Trcd_266 0x1 /* 3clk */
#define B6_SCAN 0x2 /* 10bit */
#define B7_MT 0x3 /* SDRAM */
#define B7_Trcd_200 0x0 /* 2clk */
#define B7_Trcd_250 0x1 /* 3clk */
#define B7_Trcd_266 0x1 /* 3clk */
#define B7_SCAN 0x2 /* 10bit */
/* REFRESH parameter */
#define REFEN 0x1 /* Refresh enable */
#define TREFMD 0x0 /* CBR(CAS before RAS)/Auto refresh */
#define Trp_200 0x0 /* 2clk */
#define Trp_250 0x1 /* 3clk */
#define Trp_266 0x1 /* 3clk */
#define Tsrc_200 0x1 /* 5clk */
#define Tsrc_250 0x2 /* 6clk */
#define Tsrc_266 0x3 /* 7clk */
/* period=15.6us, HCLK=100Mhz, (2048+1-15.6*100) */
#define REFCNT_200 489
/* period=15.6us, HCLK=125Mhz, (2048+1-15.6*125) */
#define REFCNT_250 99
/* period=15.6us, HCLK=133Mhz, (2048+1-15.6*133) */
#define REFCNT_266 0
/**************************************/
.globl lowlevel_init
lowlevel_init:
/* use r0 to relocate DATA read/write to flash rather than memory ! */
ldr r0, =CONFIG_SYS_TEXT_BASE
ldr r13, =BWSCON
/* enable minimal access to PLD */
ldr r1, [r13] /* load default BWSCON */
orr r1, r1, #(DW8 + UBLB) << 20 /* set necessary CS attrs */
str r1, [r13] /* set BWSCON */
ldr r1, =0x7FF0 /* select slowest timing */
str r1, [r13, #0x18] /* set BANKCON5 */
ldr r1, =PLD_BASE
ldr r2, =SETUPDATA
ldrb r1, [r1, #MISC_REG]
sub r2, r2, r0
tst r1, #FASTCPU /* FASTCPU available ? */
addeq r2, r2, #SETUPENTRY_SIZE
/* memory control configuration */
/* r2 = pointer into timing table */
/* r13 = pointer to MEM controller regs (starting with BWSCON) */
add r3, r2, #CSDATA_OFFSET
add r4, r3, #CSDATAENTRY_SIZE
0:
ldr r1, [r3], #4
str r1, [r13], #4
cmp r3, r4
bne 0b
/* PLD access is now possible */
/* r3 = SDRAMDATA */
/* r13 = pointer to MEM controller regs */
ldr r1, =PLD_BASE
mov r4, #SDRAMENTRY_SIZE
ldrb r1, [r1, #SDRAM_REG]
/* calculate start and end point */
mla r3, r4, r1, r3
add r4, r3, r4
0:
ldr r1, [r3], #4
str r1, [r13], #4
cmp r3, r4
bne 0b
/* setup MPLL registers */
ldr r1, =CLKBASE
ldr r4, =0xFFFFFF
add r3, r2, #4 /* r3 points to PLL values */
str r4, [r1, #LOCKTIME]
ldmia r3, {r4,r5}
str r5, [r1, #UPLLCON] /* writing PLL register */
/* !! order seems to be important !! */
/* a little delay */
ldr r3, =0x4000
0:
subs r3, r3, #1
bne 0b
str r4, [r1, #MPLLCON] /* writing PLL register */
/* !! order seems to be important !! */
/* a little delay */
ldr r3, =0x4000
0:
subs r3, r3, #1
bne 0b
/* everything is fine now */
mov pc, lr
.ltorg
/* the literal pools origin */
#define MK_BWSCON(bws1, bws2, bws3, bws4, bws5, bws6, bws7) \
((bws1) << 4) + \
((bws2) << 8) + \
((bws3) << 12) + \
((bws4) << 16) + \
((bws5) << 20) + \
((bws6) << 24) + \
((bws7) << 28)
#define MK_BANKCON(tacs, tcos, tacc, tcoh, tcah, tacp, pmc) \
((tacs) << 13) + \
((tcos) << 11) + \
((tacc) << 8) + \
((tcoh) << 6) + \
((tcah) << 4) + \
((tacp) << 2) + \
(pmc)
#define MK_BANKCON_SDRAM(trcd, scan) \
((0x03) << 15) + \
((trcd) << 2) + \
(scan)
#define MK_SDRAM_REFRESH(enable, trefmd, trp, tsrc, cnt) \
((enable) << 23) + \
((trefmd) << 22) + \
((trp) << 20) + \
((tsrc) << 18) + \
(cnt)
SETUPDATA:
.word 0x32410002
/* PLL values (MDIV, PDIV, SDIV) for 250 MHz */
.word (0x75 << 12) + (0x01 << 4) + (0x01 << 0)
/* PLL values for USB clock */
.word (0x48 << 12) + (0x03 << 4) + (0x02 << 0)
/* timing for 250 MHz*/
0:
.equiv CSDATA_OFFSET, (. - SETUPDATA)
.word MK_BWSCON(DW16, \
DW32, \
DW32, \
DW16 + WAIT + UBLB, \
DW8 + UBLB, \
DW32, \
DW32)
.word MK_BANKCON(B0_Tacs_250, \
B0_Tcos_250, \
B0_Tacc_250, \
B0_Tcoh_250, \
B0_Tcah_250, \
B0_Tacp_250, \
B0_PMC_250)
.word MK_BANKCON(B1_Tacs_250, \
B1_Tcos_250, \
B1_Tacc_250, \
B1_Tcoh_250, \
B1_Tcah_250, \
B1_Tacp_250, \
B1_PMC_250)
.word MK_BANKCON(B2_Tacs, \
B2_Tcos, \
B2_Tacc, \
B2_Tcoh, \
B2_Tcah, \
B2_Tacp, \
B2_PMC)
.word MK_BANKCON(B3_Tacs, \
B3_Tcos, \
B3_Tacc, \
B3_Tcoh, \
B3_Tcah, \
B3_Tacp, \
B3_PMC)
.word MK_BANKCON(B4_Tacs_250, \
B4_Tcos_250, \
B4_Tacc_250, \
B4_Tcoh_250, \
B4_Tcah_250, \
B4_Tacp_250, \
B4_PMC_250)
.word MK_BANKCON(B5_Tacs_250, \
B5_Tcos_250, \
B5_Tacc_250, \
B5_Tcoh_250, \
B5_Tcah_250, \
B5_Tacp_250, \
B5_PMC_250)
.equiv CSDATAENTRY_SIZE, (. - 0b)
/* 4Mx8x4 */
0:
.word MK_BANKCON_SDRAM(B6_Trcd_250, B6_SCAN)
.word MK_BANKCON_SDRAM(B7_Trcd_250, B7_SCAN)
.word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_250, Tsrc_250, REFCNT_250)
.word 0x32 + BURST_EN
.word 0x30
.word 0x30
.equiv SDRAMENTRY_SIZE, (. - 0b)
/* 8Mx8x4 */
.word MK_BANKCON_SDRAM(B6_Trcd_250, B6_SCAN)
.word MK_BANKCON_SDRAM(B7_Trcd_250, B7_SCAN)
.word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_250, Tsrc_250, REFCNT_250)
.word 0x32 + BURST_EN
.word 0x30
.word 0x30
/* 2Mx8x4 */
.word MK_BANKCON_SDRAM(B6_Trcd_250, B6_SCAN)
.word MK_BANKCON_SDRAM(B7_Trcd_250, B7_SCAN)
.word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_250, Tsrc_250, REFCNT_250)
.word 0x32 + BURST_EN
.word 0x30
.word 0x30
/* 4Mx8x2 */
.word MK_BANKCON_SDRAM(B6_Trcd_250, B6_SCAN)
.word MK_BANKCON_SDRAM(B7_Trcd_250, B7_SCAN)
.word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_250, Tsrc_250, REFCNT_250)
.word 0x32 + BURST_EN
.word 0x30
.word 0x30
.equiv SETUPENTRY_SIZE, (. - SETUPDATA)
.word 0x32410000
/* PLL values (MDIV, PDIV, SDIV) for 200 MHz (Fout = 202.8MHz) */
.word (0xA1 << 12) + (0x03 << 4) + (0x01 << 0)
/* PLL values for USB clock */
.word (0x48 << 12) + (0x03 << 4) + (0x02 << 0)
/* timing for 200 MHz and default*/
.word MK_BWSCON(DW16, \
DW32, \
DW32, \
DW16 + WAIT + UBLB, \
DW8 + UBLB, \
DW32, \
DW32)
.word MK_BANKCON(B0_Tacs_200, \
B0_Tcos_200, \
B0_Tacc_200, \
B0_Tcoh_200, \
B0_Tcah_200, \
B0_Tacp_200, \
B0_PMC_200)
.word MK_BANKCON(B1_Tacs_200, \
B1_Tcos_200, \
B1_Tacc_200, \
B1_Tcoh_200, \
B1_Tcah_200, \
B1_Tacp_200, \
B1_PMC_200)
.word MK_BANKCON(B2_Tacs, \
B2_Tcos, \
B2_Tacc, \
B2_Tcoh, \
B2_Tcah, \
B2_Tacp, \
B2_PMC)
.word MK_BANKCON(B3_Tacs, \
B3_Tcos, \
B3_Tacc, \
B3_Tcoh, \
B3_Tcah, \
B3_Tacp, \
B3_PMC)
.word MK_BANKCON(B4_Tacs_200, \
B4_Tcos_200, \
B4_Tacc_200, \
B4_Tcoh_200, \
B4_Tcah_200, \
B4_Tacp_200, \
B4_PMC_200)
.word MK_BANKCON(B5_Tacs_200, \
B5_Tcos_200, \
B5_Tacc_200, \
B5_Tcoh_200, \
B5_Tcah_200, \
B5_Tacp_200, \
B5_PMC_200)
/* 4Mx8x4 */
.word MK_BANKCON_SDRAM(B6_Trcd_200, B6_SCAN)
.word MK_BANKCON_SDRAM(B7_Trcd_200, B7_SCAN)
.word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_200, Tsrc_200, REFCNT_200)
.word 0x32 + BURST_EN
.word 0x30
.word 0x30
/* 8Mx8x4 */
.word MK_BANKCON_SDRAM(B6_Trcd_200, B6_SCAN)
.word MK_BANKCON_SDRAM(B7_Trcd_200, B7_SCAN)
.word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_200, Tsrc_200, REFCNT_200)
.word 0x32 + BURST_EN
.word 0x30
.word 0x30
/* 2Mx8x4 */
.word MK_BANKCON_SDRAM(B6_Trcd_200, B6_SCAN)
.word MK_BANKCON_SDRAM(B7_Trcd_200, B7_SCAN)
.word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_200, Tsrc_200, REFCNT_200)
.word 0x32 + BURST_EN
.word 0x30
.word 0x30
/* 4Mx8x2 */
.word MK_BANKCON_SDRAM(B6_Trcd_200, B6_SCAN)
.word MK_BANKCON_SDRAM(B7_Trcd_200, B7_SCAN)
.word MK_SDRAM_REFRESH(REFEN, TREFMD, Trp_200, Tsrc_200, REFCNT_200)
.word 0x32 + BURST_EN
.word 0x30
.word 0x30
.equiv SETUPDATA_SIZE, (. - SETUPDATA)