blob: 0989407fc7db8093204d6b25516bfdb4080f85fe [file] [log] [blame]
/*
* (C) Copyright 2007
* Matthias Fuchs, esd gmbh, matthias.fuchs@esd-electronics.com
*
* (C) Copyright 2001-2004
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* board/config.h - configuration options, board specific
*/
#ifndef __CONFIG_H
#define __CONFIG_H
/*
* High Level Configuration Options
* (easy to change)
*/
#define CONFIG_405GP 1 /* This is a PPC405 CPU */
#define CONFIG_PCI405 1 /* ...on a PCI405 board */
#define CONFIG_SYS_TEXT_BASE 0xFFFD0000
#define CONFIG_BOARD_EARLY_INIT_F 1 /* call board_early_init_f() */
#define CONFIG_MISC_INIT_R 1 /* call misc_init_r() on init */
#define CONFIG_SYS_CLK_FREQ 25000000 /* external frequency to pll */
#define CONFIG_BOARD_TYPES 1 /* support board types */
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOOTDELAY 0 /* autoboot after 0 seconds */
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"mem_linux=14336k\0" \
"optargs=panic=0\0" \
"ramargs=setenv bootargs mem=$mem_linux root=/dev/ram rw\0" \
"addcons=setenv bootargs $bootargs console=ttyS0,$baudrate $optargs\0" \
""
#define CONFIG_BOOTCOMMAND "run ramargs;run addcons;loadpci"
#define CONFIG_PREBOOT /* enable preboot variable */
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#undef CONFIG_CMD_IMLS
#undef CONFIG_CMD_ITEST
#undef CONFIG_CMD_LOADB
#undef CONFIG_CMD_LOADS
#undef CONFIG_CMD_NET
#undef CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
#define CONFIG_CMD_ELF
#define CONFIG_CMD_I2C
#define CONFIG_CMD_BSP
#define CONFIG_CMD_EEPROM
#undef CONFIG_WATCHDOG /* watchdog disabled */
#define CONFIG_SDRAM_BANK0 1 /* init onboard SDRAM bank 0 */
#define CONFIG_PRAM 2048 /* reserve 2 MB "protected RAM" */
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_HUSH_PARSER /* use "hush" command parser */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_DEVICE_NULLDEV 1 /* include nulldev device */
#define CONFIG_SYS_CONSOLE_INFO_QUIET 1 /* don't print console @ startup*/
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#undef CONFIG_SYS_EXT_SERIAL_CLOCK /* no external serial clock used */
#define CONFIG_SYS_BASE_BAUD 691200
/* The following table includes the supported baudrates */
#define CONFIG_SYS_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
#undef CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* PCI stuff
*-----------------------------------------------------------------------
*/
#define PCI_HOST_ADAPTER 0 /* configure as pci adapter */
#define PCI_HOST_FORCE 1 /* configure as pci host */
#define PCI_HOST_AUTO 2 /* detected via arbiter enable */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_INDIRECT_BRIDGE /* indirect PCI bridge support */
#define CONFIG_PCI_HOST PCI_HOST_ADAPTER /* select pci host function */
#undef CONFIG_PCI_PNP /* no pci plug-and-play */
/* resource configuration */
#define CONFIG_PCI_SCAN_SHOW /* print pci devices @ startup */
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x12FE /* PCI Vendor ID: esd gmbh */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0x0407 /* PCI Device ID: PCI-405 */
#define CONFIG_SYS_PCI_CLASSCODE 0x0280 /* PCI Class Code: Network/Other*/
#define CONFIG_SYS_PCI_PTM1LA 0x00000000 /* point to sdram */
#define CONFIG_SYS_PCI_PTM1MS 0xff000001 /* 16MB, enable hard-wired to 1 */
#define CONFIG_SYS_PCI_PTM1PCI 0x00000000 /* Host: use this pci address */
#define CONFIG_SYS_PCI_PTM2LA 0xef600000 /* point to internal regs */
#define CONFIG_SYS_PCI_PTM2MS 0xffe00001 /* 2MB, enable */
#define CONFIG_SYS_PCI_PTM2PCI 0x00000000 /* Host: use this pci address */
/*-----------------------------------------------------------------------
* Start addresses for the final memory configuration
* (Set up by the startup code)
* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000
#define CONFIG_SYS_FLASH_BASE 0xFFFD0000
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN (192 * 1024) /* Reserve 196 kB for Monitor */
#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc() */
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
/*-----------------------------------------------------------------------
* FLASH organization
*/
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_FLASH_WORD_SIZE unsigned short /* flash word size (width) */
#define CONFIG_SYS_FLASH_ADDR0 0x5555 /* 1st address for flash config cycles */
#define CONFIG_SYS_FLASH_ADDR1 0x2AAA /* 2nd address for flash config cycles */
/*
* The following defines are added for buggy IOP480 byte interface.
* All other boards should use the standard values (CPCI405 etc.)
*/
#define CONFIG_SYS_FLASH_READ0 0x0000 /* 0 is standard */
#define CONFIG_SYS_FLASH_READ1 0x0001 /* 1 is standard */
#define CONFIG_SYS_FLASH_READ2 0x0002 /* 2 is standard */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CONFIG_ENV_IS_IN_EEPROM 1 /* use EEPROM for environment vars */
#define CONFIG_ENV_OFFSET 0x000 /* environment starts at the beginning of the EEPROM */
#define CONFIG_ENV_SIZE 0x400 /* 1024 bytes may be used for env vars*/
/* total size of a CAT24WC08 is 1024 bytes */
#define CONFIG_SYS_NVRAM_BASE_ADDR 0xf0200000 /* NVRAM base address */
#define CONFIG_SYS_NVRAM_SIZE (32*1024) /* NVRAM size */
/*-----------------------------------------------------------------------
* I2C EEPROM (CAT24WC16) for environment
*/
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_PPC4XX
#define CONFIG_SYS_I2C_PPC4XX_CH0
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 400000
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50 /* EEPROM CAT28WC08 */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 4 /* The Catalyst CAT24WC08 has */
/* 16 byte page write mode using*/
/* last 4 bits of the address */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 10 /* and takes up to 10 msec */
/*
* Init Memory Controller:
*
* BR0/1 and OR0/1 (FLASH)
*/
#define FLASH_BASE0_PRELIM 0xFFE00000 /* FLASH bank #0 */
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*/
/* Memory Bank 0 (Flash Bank 0) initialization */
#define CONFIG_SYS_EBC_PB0AP 0x92015480
#define CONFIG_SYS_EBC_PB0CR 0xFFC5A000 /* BAS=0xFFC,BS=4MB,BU=R/W,BW=16bit */
/* Memory Bank 1 (NVRAM/RTC) initialization */
#define CONFIG_SYS_EBC_PB1AP 0x01005280 /* TWT=2,WBN=1,WBF=1,TH=1,SOR=1 */
#define CONFIG_SYS_EBC_PB1CR 0xF0218000 /* BAS=0xF02,BS=1MB,BU=R/W,BW=8bit */
/* Memory Bank 2 (CAN0, 1) initialization */
#define CONFIG_SYS_EBC_PB2AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
/*#define CONFIG_SYS_EBC_PB2AP 0x038056C0 / * BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB2CR 0xF0018000 /* BAS=0xF00,BS=1MB,BU=R/W,BW=8bit */
/* Memory Bank 3 (FPGA internal) initialization */
#define CONFIG_SYS_EBC_PB3AP 0x010053C0 /* BWT=2,WBN=1,WBF=1,TH=1,RE=1,SOR=1,BEM=1 */
#define CONFIG_SYS_EBC_PB3CR 0xF041C000 /* BAS=0xF01,BS=1MB,BU=R/W,BW=32bit */
#define CONFIG_SYS_FPGA_BASE_ADDR 0xF0400000
/*-----------------------------------------------------------------------
* FPGA stuff
*/
/* FPGA internal regs */
#define CONFIG_SYS_FPGA_MODE 0x00
#define CONFIG_SYS_FPGA_STATUS 0x02
#define CONFIG_SYS_FPGA_TS 0x04
#define CONFIG_SYS_FPGA_TS_LOW 0x06
#define CONFIG_SYS_FPGA_TS_CAP0 0x10
#define CONFIG_SYS_FPGA_TS_CAP0_LOW 0x12
#define CONFIG_SYS_FPGA_TS_CAP1 0x14
#define CONFIG_SYS_FPGA_TS_CAP1_LOW 0x16
#define CONFIG_SYS_FPGA_TS_CAP2 0x18
#define CONFIG_SYS_FPGA_TS_CAP2_LOW 0x1a
#define CONFIG_SYS_FPGA_TS_CAP3 0x1c
#define CONFIG_SYS_FPGA_TS_CAP3_LOW 0x1e
/* FPGA Mode Reg */
#define CONFIG_SYS_FPGA_MODE_CF_RESET 0x0001
#define CONFIG_SYS_FPGA_MODE_TS_IRQ_ENABLE 0x0100
#define CONFIG_SYS_FPGA_MODE_TS_IRQ_CLEAR 0x1000
#define CONFIG_SYS_FPGA_MODE_TS_CLEAR 0x2000
/* FPGA Status Reg */
#define CONFIG_SYS_FPGA_STATUS_DIP0 0x0001
#define CONFIG_SYS_FPGA_STATUS_DIP1 0x0002
#define CONFIG_SYS_FPGA_STATUS_DIP2 0x0004
#define CONFIG_SYS_FPGA_STATUS_FLASH 0x0008
#define CONFIG_SYS_FPGA_STATUS_TS_IRQ 0x1000
#define CONFIG_SYS_FPGA_SPARTAN2 1 /* using Xilinx Spartan 2 now */
#define CONFIG_SYS_FPGA_MAX_SIZE 32*1024 /* 32kByte is enough for XC2S15 */
/* FPGA program pin configuration */
#define CONFIG_SYS_FPGA_PRG 0x04000000 /* FPGA program pin (ppc output) */
#define CONFIG_SYS_FPGA_CLK 0x02000000 /* FPGA clk pin (ppc output) */
#define CONFIG_SYS_FPGA_DATA 0x01000000 /* FPGA data pin (ppc output) */
#define CONFIG_SYS_FPGA_INIT 0x00400000 /* FPGA init pin (ppc input) */
#define CONFIG_SYS_FPGA_DONE 0x00800000 /* FPGA done pin (ppc input) */
/* new INIT and DONE pins since board revision 1.2 (for PPC405GPr support) */
#define CONFIG_SYS_FPGA_INIT_V12 0x00008000 /* FPGA init pin (ppc input) */
#define CONFIG_SYS_FPGA_DONE_V12 0x00010000 /* FPGA done pin (ppc input) */
/*-----------------------------------------------------------------------
* Definitions for initial stack pointer and data area (in data cache)
*/
/* use on chip memory ( OCM ) for temperary stack until sdram is tested */
#define CONFIG_SYS_TEMP_STACK_OCM 1
/* On Chip Memory location */
#define CONFIG_SYS_OCM_DATA_ADDR 0xF8000000
#define CONFIG_SYS_OCM_DATA_SIZE 0x1000
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM */
#define CONFIG_SYS_INIT_RAM_SIZE CONFIG_SYS_OCM_DATA_SIZE /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#endif /* __CONFIG_H */