include/configs/TQM823M.h - u-boot - Git at Google

 /*
  * (C) Copyright 2000-2014
  * Wolfgang Denk, DENX Software Engineering, wd@denx.de.
  *
  * SPDX-License-Identifier:	GPL-2.0+
  */

 /*
  * board/config.h - configuration options, board specific
  */

 #ifndef __CONFIG_H
 #define __CONFIG_H

 /*
  * High Level Configuration Options
  * (easy to change)
  */

 #define CONFIG_MPC823		1	/* This is a MPC823 CPU		*/
 #define CONFIG_TQM823M		1	/* ...on a TQM8xxM module	*/
 #define CONFIG_SYS_GENERIC_BOARD
 #define CONFIG_DISPLAY_BOARDINFO

 #define	CONFIG_SYS_TEXT_BASE	0x40000000

 #ifdef	CONFIG_LCD			/* with LCD controller ?	*/
 #define CONFIG_MPC8XX_LCD
 /* #define CONFIG_NEC_NL6448BC20 1 / * use NEC NL6448BC20 display	*/
 #endif

 #define	CONFIG_8xx_CONS_SMC1	1	/* Console is on SMC1		*/
 #define CONFIG_SYS_SMC_RXBUFLEN	128
 #define CONFIG_SYS_MAXIDLE	10
 #define CONFIG_BAUDRATE		115200	/* console baudrate = 115kbps	*/

 #define	CONFIG_BOOTCOUNT_LIMIT

 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/

 #define CONFIG_BOARD_TYPES	1	/* support board types		*/

 #define CONFIG_PREBOOT	"echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"

 #undef	CONFIG_BOOTARGS

 #define	CONFIG_EXTRA_ENV_SETTINGS					\
 	"netdev=eth0\0"							\
 	"nfsargs=setenv bootargs root=/dev/nfs rw "			\
 		"nfsroot=${serverip}:${rootpath}\0"			\
 	"ramargs=setenv bootargs root=/dev/ram rw\0"			\
 	"addip=setenv bootargs ${bootargs} "				\
 		"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}"	\
 		":${hostname}:${netdev}:off panic=1\0"			\
 	"flash_nfs=run nfsargs addip;"					\
 		"bootm ${kernel_addr}\0"				\
 	"flash_self=run ramargs addip;"					\
 		"bootm ${kernel_addr} ${ramdisk_addr}\0"		\
 	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0"	\
 	"rootpath=/opt/eldk/ppc_8xx\0"					\
 	"hostname=TQM823M\0"						\
 	"bootfile=TQM823M/uImage\0"					\
 	"fdt_addr=40080000\0"						\
 	"kernel_addr=400A0000\0"					\
 	"ramdisk_addr=40280000\0"					\
 	"u-boot=TQM823M/u-image.bin\0"					\
 	"load=tftp 200000 ${u-boot}\0"					\
 	"update=prot off 40000000 +${filesize};"			\
 		"era 40000000 +${filesize};"				\
 		"cp.b 200000 40000000 ${filesize};"			\
 		"sete filesize;save\0"					\
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"

 #define CONFIG_LOADS_ECHO	1	/* echo on for serial download	*/
 #undef	CONFIG_SYS_LOADS_BAUD_CHANGE		/* don't allow baudrate change	*/

 #undef	CONFIG_WATCHDOG			/* watchdog disabled		*/

 #ifdef CONFIG_LCD
 # undef	 CONFIG_STATUS_LED		/* disturbs display		*/
 #else
 # define CONFIG_STATUS_LED	1	/* Status LED enabled		*/
 #endif	/* CONFIG_LCD */

 #undef	CONFIG_CAN_DRIVER		/* CAN Driver support disabled	*/

 /*
  * BOOTP options
  */
 #define CONFIG_BOOTP_SUBNETMASK
 #define CONFIG_BOOTP_GATEWAY
 #define CONFIG_BOOTP_HOSTNAME
 #define CONFIG_BOOTP_BOOTPATH
 #define CONFIG_BOOTP_BOOTFILESIZE


 #define CONFIG_MAC_PARTITION
 #define CONFIG_DOS_PARTITION

 #define	CONFIG_RTC_MPC8xx		/* use internal RTC of MPC8xx	*/


 /*
  * Command line configuration.
  */
 #include <config_cmd_default.h>

 #define CONFIG_CMD_ASKENV
 #define CONFIG_CMD_DATE
 #define CONFIG_CMD_DHCP
 #define CONFIG_CMD_ELF
 #define CONFIG_CMD_EXT2
 #define CONFIG_CMD_IDE
 #define CONFIG_CMD_JFFS2
 #define CONFIG_CMD_NFS
 #define CONFIG_CMD_SNTP


 #define CONFIG_NETCONSOLE


 /*
  * Miscellaneous configurable options
  */
 #define	CONFIG_SYS_LONGHELP			/* undef to save memory		*/

 #define CONFIG_CMDLINE_EDITING	1	/* add command line history	*/
 #define CONFIG_SYS_HUSH_PARSER		1	/* Use the HUSH parser		*/

 #if defined(CONFIG_CMD_KGDB)
 #define	CONFIG_SYS_CBSIZE		1024	/* Console I/O Buffer Size	*/
 #else
 #define	CONFIG_SYS_CBSIZE		256	/* Console I/O Buffer Size	*/
 #endif
 #define	CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
 #define	CONFIG_SYS_MAXARGS		16	/* max number of command args	*/
 #define CONFIG_SYS_BARGSIZE	CONFIG_SYS_CBSIZE	/* Boot Argument Buffer Size	*/

 #define CONFIG_SYS_MEMTEST_START	0x0400000	/* memtest works on	*/
 #define CONFIG_SYS_MEMTEST_END		0x0C00000	/* 4 ... 12 MB in DRAM	*/

 #define	CONFIG_SYS_LOAD_ADDR		0x100000	/* default load address	*/

 /*
  * Low Level Configuration Settings
  * (address mappings, register initial values, etc.)
  * You should know what you are doing if you make changes here.
  */
 /*-----------------------------------------------------------------------
  * Internal Memory Mapped Register
  */
 #define CONFIG_SYS_IMMR		0xFFF00000

 /*-----------------------------------------------------------------------
  * Definitions for initial stack pointer and data area (in DPRAM)
  */
 #define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_IMMR
 #define	CONFIG_SYS_INIT_RAM_SIZE	0x2F00	/* Size of used area in DPRAM	*/
 #define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
 #define	CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET

 /*-----------------------------------------------------------------------
  * Start addresses for the final memory configuration
  * (Set up by the startup code)
  * Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
  */
 #define	CONFIG_SYS_SDRAM_BASE		0x00000000
 #define CONFIG_SYS_FLASH_BASE		0x40000000
 #define	CONFIG_SYS_MONITOR_LEN		(256 << 10)	/* Reserve 256 kB for Monitor	*/
 #define CONFIG_SYS_MONITOR_BASE	CONFIG_SYS_FLASH_BASE
 #define	CONFIG_SYS_MALLOC_LEN		(128 << 10)	/* Reserve 128 kB for malloc()	*/

 /*
  * For booting Linux, the board info and command line data
  * have to be in the first 8 MB of memory, since this is
  * the maximum mapped by the Linux kernel during initialization.
  */
 #define	CONFIG_SYS_BOOTMAPSZ		(8 << 20)	/* Initial Memory map for Linux	*/

 /*-----------------------------------------------------------------------
  * FLASH organization
  */

 /* use CFI flash driver */
 #define CONFIG_SYS_FLASH_CFI		1	/* Flash is CFI conformant */
 #define CONFIG_FLASH_CFI_DRIVER	1	/* Use the common driver */
 #define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
 #define CONFIG_SYS_FLASH_EMPTY_INFO
 #define CONFIG_SYS_FLASH_USE_BUFFER_WRITE	1
 #define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks */
 #define CONFIG_SYS_MAX_FLASH_SECT	256	/* max number of sectors on one chip */

 #define	CONFIG_ENV_IS_IN_FLASH	1
 #define	CONFIG_ENV_OFFSET		0x40000	/*   Offset   of Environment Sector	*/
 #define	CONFIG_ENV_SIZE		0x08000	/* Total Size of Environment		*/
 #define	CONFIG_ENV_SECT_SIZE	0x20000	/* Total Size of Environment Sector	*/

 /* Address and size of Redundant Environment Sector	*/
 #define CONFIG_ENV_OFFSET_REDUND	(CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
 #define CONFIG_ENV_SIZE_REDUND	(CONFIG_ENV_SIZE)

 #define	CONFIG_SYS_USE_PPCENV			/* Environment embedded in sect .ppcenv */

 #define CONFIG_MISC_INIT_R		/* Make sure to remap flashes correctly */

 /*-----------------------------------------------------------------------
  * Dynamic MTD partition support
  */
 #define CONFIG_CMD_MTDPARTS
 #define CONFIG_MTD_DEVICE		/* needed for mtdparts commands */
 #define CONFIG_FLASH_CFI_MTD
 #define MTDIDS_DEFAULT		"nor0=TQM8xxM-0"

 #define MTDPARTS_DEFAULT	"mtdparts=TQM8xxM-0:512k(u-boot),"	\
 						"128k(dtb),"		\
 						"1920k(kernel),"	\
 						"5632(rootfs),"		\
 						"4m(data)"

 /*-----------------------------------------------------------------------
  * Hardware Information Block
  */
 #define CONFIG_SYS_HWINFO_OFFSET	0x0003FFC0	/* offset of HW Info block */
 #define CONFIG_SYS_HWINFO_SIZE		0x00000040	/* size   of HW Info block */
 #define CONFIG_SYS_HWINFO_MAGIC	0x54514D38	/* 'TQM8' */

 /*-----------------------------------------------------------------------
  * Cache Configuration
  */
 #define CONFIG_SYS_CACHELINE_SIZE	16	/* For all MPC8xx CPUs			*/
 #if defined(CONFIG_CMD_KGDB)
 #define CONFIG_SYS_CACHELINE_SHIFT	4	/* log base 2 of the above value	*/
 #endif

 /*-----------------------------------------------------------------------
  * SYPCR - System Protection Control				11-9
  * SYPCR can only be written once after reset!
  *-----------------------------------------------------------------------
  * Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
  */
 #if defined(CONFIG_WATCHDOG)
 #define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | \
 			 SYPCR_SWE  | SYPCR_SWRI| SYPCR_SWP)
 #else
 #define CONFIG_SYS_SYPCR	(SYPCR_SWTC | SYPCR_BMT | SYPCR_BME | SYPCR_SWF | SYPCR_SWP)
 #endif

 /*-----------------------------------------------------------------------
  * SIUMCR - SIU Module Configuration				11-6
  *-----------------------------------------------------------------------
  * PCMCIA config., multi-function pin tri-state
  */
 #ifndef	CONFIG_CAN_DRIVER
 #define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC00 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 #else	/* we must activate GPL5 in the SIUMCR for CAN */
 #define CONFIG_SYS_SIUMCR	(SIUMCR_DBGC11 | SIUMCR_DBPC00 | SIUMCR_MLRC01)
 #endif	/* CONFIG_CAN_DRIVER */

 /*-----------------------------------------------------------------------
  * TBSCR - Time Base Status and Control				11-26
  *-----------------------------------------------------------------------
  * Clear Reference Interrupt Status, Timebase freezing enabled
  */
 #define CONFIG_SYS_TBSCR	(TBSCR_REFA | TBSCR_REFB | TBSCR_TBF)

 /*-----------------------------------------------------------------------
  * RTCSC - Real-Time Clock Status and Control Register		11-27
  *-----------------------------------------------------------------------
  */
 #define CONFIG_SYS_RTCSC	(RTCSC_SEC | RTCSC_ALR | RTCSC_RTF| RTCSC_RTE)

 /*-----------------------------------------------------------------------
  * PISCR - Periodic Interrupt Status and Control		11-31
  *-----------------------------------------------------------------------
  * Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
  */
 #define CONFIG_SYS_PISCR	(PISCR_PS | PISCR_PITF)

 /*-----------------------------------------------------------------------
  * PLPRCR - PLL, Low-Power, and Reset Control Register		15-30
  *-----------------------------------------------------------------------
  * Reset PLL lock status sticky bit, timer expired status bit and timer
  * interrupt status bit
  */
 #define CONFIG_SYS_PLPRCR	(PLPRCR_SPLSS | PLPRCR_TEXPS | PLPRCR_TMIST)

 /*-----------------------------------------------------------------------
  * SCCR - System Clock and reset Control Register		15-27
  *-----------------------------------------------------------------------
  * Set clock output, timebase and RTC source and divider,
  * power management and some other internal clocks
  */
 #define SCCR_MASK	SCCR_EBDF11
 #define CONFIG_SYS_SCCR	(SCCR_COM00   | SCCR_DFSYNC00 | SCCR_DFBRG00  | \
 			 SCCR_DFNL000 | SCCR_DFNH000  | SCCR_DFLCD000 | \
 			 SCCR_DFALCD00)

 /*-----------------------------------------------------------------------
  * PCMCIA stuff
  *-----------------------------------------------------------------------
  *
  */
 #define CONFIG_SYS_PCMCIA_MEM_ADDR	(0xE0000000)
 #define CONFIG_SYS_PCMCIA_MEM_SIZE	( 64 << 20 )
 #define CONFIG_SYS_PCMCIA_DMA_ADDR	(0xE4000000)
 #define CONFIG_SYS_PCMCIA_DMA_SIZE	( 64 << 20 )
 #define CONFIG_SYS_PCMCIA_ATTRB_ADDR	(0xE8000000)
 #define CONFIG_SYS_PCMCIA_ATTRB_SIZE	( 64 << 20 )
 #define CONFIG_SYS_PCMCIA_IO_ADDR	(0xEC000000)
 #define CONFIG_SYS_PCMCIA_IO_SIZE	( 64 << 20 )

 /*-----------------------------------------------------------------------
  * IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
  *-----------------------------------------------------------------------
  */

 #define CONFIG_IDE_PREINIT	1	/* Use preinit IDE hook */
 #define	CONFIG_IDE_8xx_PCCARD	1	/* Use IDE with PC Card	Adapter	*/

 #undef	CONFIG_IDE_8xx_DIRECT		/* Direct IDE    not supported	*/
 #undef	CONFIG_IDE_LED			/* LED   for ide not supported	*/
 #undef	CONFIG_IDE_RESET		/* reset for ide not supported	*/

 #define CONFIG_SYS_IDE_MAXBUS		1	/* max. 1 IDE bus		*/
 #define CONFIG_SYS_IDE_MAXDEVICE	1	/* max. 1 drive per IDE bus	*/

 #define CONFIG_SYS_ATA_IDE0_OFFSET	0x0000

 #define CONFIG_SYS_ATA_BASE_ADDR	CONFIG_SYS_PCMCIA_MEM_ADDR

 /* Offset for data I/O			*/
 #define CONFIG_SYS_ATA_DATA_OFFSET	(CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)

 /* Offset for normal register accesses	*/
 #define CONFIG_SYS_ATA_REG_OFFSET	(2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)

 /* Offset for alternate registers	*/
 #define CONFIG_SYS_ATA_ALT_OFFSET	0x0100

 /*-----------------------------------------------------------------------
  *
  *-----------------------------------------------------------------------
  *
  */
 #define CONFIG_SYS_DER	0

 /*
  * Init Memory Controller:
  *
  * BR0/1 and OR0/1 (FLASH)
  */

 #define FLASH_BASE0_PRELIM	0x40000000	/* FLASH bank #0	*/
 #define FLASH_BASE1_PRELIM	0x60000000	/* FLASH bank #0	*/

 /* used to re-map FLASH both when starting from SRAM or FLASH:
  * restrict access enough to keep SRAM working (if any)
  * but not too much to meddle with FLASH accesses
  */
 #define CONFIG_SYS_REMAP_OR_AM		0x80000000	/* OR addr mask */
 #define CONFIG_SYS_PRELIM_OR_AM	0xE0000000	/* OR addr mask */

 /*
  * FLASH timing:
  */
 #define CONFIG_SYS_OR_TIMING_FLASH	(OR_ACS_DIV1  | OR_TRLX | OR_CSNT_SAM | \
 				 OR_SCY_3_CLK | OR_EHTR | OR_BI)

 #define CONFIG_SYS_OR0_REMAP	(CONFIG_SYS_REMAP_OR_AM  | CONFIG_SYS_OR_TIMING_FLASH)
 #define CONFIG_SYS_OR0_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_FLASH)
 #define CONFIG_SYS_BR0_PRELIM	((FLASH_BASE0_PRELIM & BR_BA_MSK) | BR_V )

 #define CONFIG_SYS_OR1_REMAP	CONFIG_SYS_OR0_REMAP
 #define CONFIG_SYS_OR1_PRELIM	CONFIG_SYS_OR0_PRELIM
 #define CONFIG_SYS_BR1_PRELIM	((FLASH_BASE1_PRELIM & BR_BA_MSK) | BR_V )

 /*
  * BR2/3 and OR2/3 (SDRAM)
  *
  */
 #define SDRAM_BASE2_PRELIM	0x00000000	/* SDRAM bank #0	*/
 #define SDRAM_BASE3_PRELIM	0x20000000	/* SDRAM bank #1	*/
 #define	SDRAM_MAX_SIZE		0x04000000	/* max 64 MB per bank	*/

 /* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care)	*/
 #define CONFIG_SYS_OR_TIMING_SDRAM	0x00000A00

 #define CONFIG_SYS_OR2_PRELIM	(CONFIG_SYS_PRELIM_OR_AM | CONFIG_SYS_OR_TIMING_SDRAM )
 #define CONFIG_SYS_BR2_PRELIM	((SDRAM_BASE2_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )

 #ifndef	CONFIG_CAN_DRIVER
 #define	CONFIG_SYS_OR3_PRELIM	CONFIG_SYS_OR2_PRELIM
 #define CONFIG_SYS_BR3_PRELIM	((SDRAM_BASE3_PRELIM & BR_BA_MSK) | BR_MS_UPMA | BR_V )
 #else	/* CAN uses CS3#, so we can have only one SDRAM bank anyway */
 #define	CONFIG_SYS_CAN_BASE		0xC0000000	/* CAN mapped at 0xC0000000	*/
 #define CONFIG_SYS_CAN_OR_AM		0xFFFF8000	/* 32 kB address mask		*/
 #define CONFIG_SYS_OR3_CAN		(CONFIG_SYS_CAN_OR_AM | OR_G5LA | OR_BI)
 #define CONFIG_SYS_BR3_CAN		((CONFIG_SYS_CAN_BASE & BR_BA_MSK) | \
 					BR_PS_8 | BR_MS_UPMB | BR_V )
 #endif	/* CONFIG_CAN_DRIVER */

 /*
  * Memory Periodic Timer Prescaler
  *
  * The Divider for PTA (refresh timer) configuration is based on an
  * example SDRAM configuration (64 MBit, one bank). The adjustment to
  * the number of chip selects (NCS) and the actually needed refresh
  * rate is done by setting MPTPR.
  *
  * PTA is calculated from
  *	PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
  *
  *	gclk	  CPU clock (not bus clock!)
  *	Trefresh  Refresh cycle * 4 (four word bursts used)
  *
  * 4096  Rows from SDRAM example configuration
  * 1000  factor s -> ms
  *   32  PTP (pre-divider from MPTPR) from SDRAM example configuration
  *    4  Number of refresh cycles per period
  *   64  Refresh cycle in ms per number of rows
  * --------------------------------------------
  * Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
  *
  * 50 MHz => 50.000.000 / Divider =  98
  * 66 Mhz => 66.000.000 / Divider = 129
  * 80 Mhz => 80.000.000 / Divider = 156
  */

 #define CONFIG_SYS_PTA_PER_CLK	((4096 * 32 * 1000) / (4 * 64))
 #define CONFIG_SYS_MAMR_PTA	98

 /*
  * For 16 MBit, refresh rates could be 31.3 us
  * (= 64 ms / 2K = 125 / quad bursts).
  * For a simpler initialization, 15.6 us is used instead.
  *
  * #define CONFIG_SYS_MPTPR_2BK_2K	MPTPR_PTP_DIV32		for 2 banks
  * #define CONFIG_SYS_MPTPR_1BK_2K	MPTPR_PTP_DIV64		for 1 bank
  */
 #define CONFIG_SYS_MPTPR_2BK_4K	MPTPR_PTP_DIV16		/* setting for 2 banks	*/
 #define CONFIG_SYS_MPTPR_1BK_4K	MPTPR_PTP_DIV32		/* setting for 1 bank	*/

 /* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit		*/
 #define CONFIG_SYS_MPTPR_2BK_8K	MPTPR_PTP_DIV8		/* setting for 2 banks	*/
 #define CONFIG_SYS_MPTPR_1BK_8K	MPTPR_PTP_DIV16		/* setting for 1 bank	*/

 /*
  * MAMR settings for SDRAM
  */

 /* 8 column SDRAM */
 #define CONFIG_SYS_MAMR_8COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
 			 MAMR_AMA_TYPE_0 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A11 |	\
 			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)
 /* 9 column SDRAM */
 #define CONFIG_SYS_MAMR_9COL	((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT)  | MAMR_PTAE	    |	\
 			 MAMR_AMA_TYPE_1 | MAMR_DSA_1_CYCL | MAMR_G0CLA_A10 |	\
 			 MAMR_RLFA_1X	 | MAMR_WLFA_1X	   | MAMR_TLFA_4X)

 /* pass open firmware flat tree */
 #define CONFIG_OF_LIBFDT	1
 #define CONFIG_OF_BOARD_SETUP	1
 #define CONFIG_HWCONFIG		1

 #endif	/* __CONFIG_H */
	/*
	* (C) Copyright 2000-2014
	* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
	*
	* SPDX-License-Identifier: GPL-2.0+
	*/

	/*
	* board/config.h - configuration options, board specific
	*/

	#ifndef __CONFIG_H
	#define __CONFIG_H

	/*
	* High Level Configuration Options
	* (easy to change)
	*/

	#define CONFIG_MPC823 1 /* This is a MPC823 CPU */
	#define CONFIG_TQM823M 1 /* ...on a TQM8xxM module */
	#define CONFIG_SYS_GENERIC_BOARD
	#define CONFIG_DISPLAY_BOARDINFO

	#define CONFIG_SYS_TEXT_BASE 0x40000000

	#ifdef CONFIG_LCD /* with LCD controller ? */
	#define CONFIG_MPC8XX_LCD
	/* #define CONFIG_NEC_NL6448BC20 1 / * use NEC NL6448BC20 display */
	#endif

	#define CONFIG_8xx_CONS_SMC1 1 /* Console is on SMC1 */
	#define CONFIG_SYS_SMC_RXBUFLEN 128
	#define CONFIG_SYS_MAXIDLE 10
	#define CONFIG_BAUDRATE 115200 /* console baudrate = 115kbps */

	#define CONFIG_BOOTCOUNT_LIMIT

	#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */

	#define CONFIG_BOARD_TYPES 1 /* support board types */

	#define CONFIG_PREBOOT "echo;echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;echo"

	#undef CONFIG_BOOTARGS

	#define CONFIG_EXTRA_ENV_SETTINGS \
	"netdev=eth0\0" \
	"nfsargs=setenv bootargs root=/dev/nfs rw " \
	"nfsroot=${serverip}:${rootpath}\0" \
	"ramargs=setenv bootargs root=/dev/ram rw\0" \
	"addip=setenv bootargs ${bootargs} " \
	"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
	":${hostname}:${netdev}:off panic=1\0" \
	"flash_nfs=run nfsargs addip;" \
	"bootm ${kernel_addr}\0" \
	"flash_self=run ramargs addip;" \
	"bootm ${kernel_addr} ${ramdisk_addr}\0" \
	"net_nfs=tftp 200000 ${bootfile};run nfsargs addip;bootm\0" \
	"rootpath=/opt/eldk/ppc_8xx\0" \
	"hostname=TQM823M\0" \
	"bootfile=TQM823M/uImage\0" \
	"fdt_addr=40080000\0" \
	"kernel_addr=400A0000\0" \
	"ramdisk_addr=40280000\0" \
	"u-boot=TQM823M/u-image.bin\0" \
	"load=tftp 200000 ${u-boot}\0" \
	"update=prot off 40000000 +${filesize};" \
	"era 40000000 +${filesize};" \
	"cp.b 200000 40000000 ${filesize};" \
	"sete filesize;save\0" \
	""
	#define CONFIG_BOOTCOMMAND "run flash_self"

	#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
	#undef CONFIG_SYS_LOADS_BAUD_CHANGE /* don't allow baudrate change */

	#undef CONFIG_WATCHDOG /* watchdog disabled */

	#ifdef CONFIG_LCD
	# undef CONFIG_STATUS_LED /* disturbs display */
	#else
	# define CONFIG_STATUS_LED 1 /* Status LED enabled */
	#endif /* CONFIG_LCD */

	#undef CONFIG_CAN_DRIVER /* CAN Driver support disabled */

	/*
	* BOOTP options
	*/
	#define CONFIG_BOOTP_SUBNETMASK
	#define CONFIG_BOOTP_GATEWAY
	#define CONFIG_BOOTP_HOSTNAME
	#define CONFIG_BOOTP_BOOTPATH
	#define CONFIG_BOOTP_BOOTFILESIZE


	#define CONFIG_MAC_PARTITION
	#define CONFIG_DOS_PARTITION

	#define CONFIG_RTC_MPC8xx /* use internal RTC of MPC8xx */


	/*
	* Command line configuration.
	*/
	#include <config_cmd_default.h>

	#define CONFIG_CMD_ASKENV
	#define CONFIG_CMD_DATE
	#define CONFIG_CMD_DHCP
	#define CONFIG_CMD_ELF
	#define CONFIG_CMD_EXT2
	#define CONFIG_CMD_IDE
	#define CONFIG_CMD_JFFS2
	#define CONFIG_CMD_NFS
	#define CONFIG_CMD_SNTP


	#define CONFIG_NETCONSOLE


	/*
	* Miscellaneous configurable options
	*/
	#define CONFIG_SYS_LONGHELP /* undef to save memory */

	#define CONFIG_CMDLINE_EDITING 1 /* add command line history */
	#define CONFIG_SYS_HUSH_PARSER 1 /* Use the HUSH parser */

	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
	#else
	#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
	#endif
	#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
	#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
	#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */

	#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
	#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */

	#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */

	/*
	* Low Level Configuration Settings
	* (address mappings, register initial values, etc.)
	* You should know what you are doing if you make changes here.
	*/
	/*-----------------------------------------------------------------------
	* Internal Memory Mapped Register
	*/
	#define CONFIG_SYS_IMMR 0xFFF00000

	/*-----------------------------------------------------------------------
	* Definitions for initial stack pointer and data area (in DPRAM)
	*/
	#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_IMMR
	#define CONFIG_SYS_INIT_RAM_SIZE 0x2F00 /* Size of used area in DPRAM */
	#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
	#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET

	/*-----------------------------------------------------------------------
	* Start addresses for the final memory configuration
	* (Set up by the startup code)
	* Please note that CONFIG_SYS_SDRAM_BASE _must_ start at 0
	*/
	#define CONFIG_SYS_SDRAM_BASE 0x00000000
	#define CONFIG_SYS_FLASH_BASE 0x40000000
	#define CONFIG_SYS_MONITOR_LEN (256 << 10) /* Reserve 256 kB for Monitor */
	#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
	#define CONFIG_SYS_MALLOC_LEN (128 << 10) /* Reserve 128 kB for malloc() */

	/*
	* For booting Linux, the board info and command line data
	* have to be in the first 8 MB of memory, since this is
	* the maximum mapped by the Linux kernel during initialization.
	*/
	#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */

	/*-----------------------------------------------------------------------
	* FLASH organization
	*/

	/* use CFI flash driver */
	#define CONFIG_SYS_FLASH_CFI 1 /* Flash is CFI conformant */
	#define CONFIG_FLASH_CFI_DRIVER 1 /* Use the common driver */
	#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH_BASE }
	#define CONFIG_SYS_FLASH_EMPTY_INFO
	#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
	#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
	#define CONFIG_SYS_MAX_FLASH_SECT 256 /* max number of sectors on one chip */

	#define CONFIG_ENV_IS_IN_FLASH 1
	#define CONFIG_ENV_OFFSET 0x40000 /* Offset of Environment Sector */
	#define CONFIG_ENV_SIZE 0x08000 /* Total Size of Environment */
	#define CONFIG_ENV_SECT_SIZE 0x20000 /* Total Size of Environment Sector */

	/* Address and size of Redundant Environment Sector */
	#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET+CONFIG_ENV_SECT_SIZE)
	#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)

	#define CONFIG_SYS_USE_PPCENV /* Environment embedded in sect .ppcenv */

	#define CONFIG_MISC_INIT_R /* Make sure to remap flashes correctly */

	/*-----------------------------------------------------------------------
	* Dynamic MTD partition support
	*/
	#define CONFIG_CMD_MTDPARTS
	#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
	#define CONFIG_FLASH_CFI_MTD
	#define MTDIDS_DEFAULT "nor0=TQM8xxM-0"

	#define MTDPARTS_DEFAULT "mtdparts=TQM8xxM-0:512k(u-boot)," \
	"128k(dtb)," \
	"1920k(kernel)," \
	"5632(rootfs)," \
	"4m(data)"

	/*-----------------------------------------------------------------------
	* Hardware Information Block
	*/
	#define CONFIG_SYS_HWINFO_OFFSET 0x0003FFC0 /* offset of HW Info block */
	#define CONFIG_SYS_HWINFO_SIZE 0x00000040 /* size of HW Info block */
	#define CONFIG_SYS_HWINFO_MAGIC 0x54514D38 /* 'TQM8' */

	/*-----------------------------------------------------------------------
	* Cache Configuration
	*/
	#define CONFIG_SYS_CACHELINE_SIZE 16 /* For all MPC8xx CPUs */
	#if defined(CONFIG_CMD_KGDB)
	#define CONFIG_SYS_CACHELINE_SHIFT 4 /* log base 2 of the above value */
	#endif

	/*-----------------------------------------------------------------------
	* SYPCR - System Protection Control 11-9
	* SYPCR can only be written once after reset!
	*-----------------------------------------------------------------------
	* Software & Bus Monitor Timer max, Bus Monitor enable, SW Watchdog freeze
	*/
	#if defined(CONFIG_WATCHDOG)
	#define CONFIG_SYS_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF \| \
	SYPCR_SWE \| SYPCR_SWRI\| SYPCR_SWP)
	#else
	#define CONFIG_SYS_SYPCR (SYPCR_SWTC \| SYPCR_BMT \| SYPCR_BME \| SYPCR_SWF \| SYPCR_SWP)
	#endif

	/*-----------------------------------------------------------------------
	* SIUMCR - SIU Module Configuration 11-6
	*-----------------------------------------------------------------------
	* PCMCIA config., multi-function pin tri-state
	*/
	#ifndef CONFIG_CAN_DRIVER
	#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC00 \| SIUMCR_DBPC00 \| SIUMCR_MLRC01)
	#else /* we must activate GPL5 in the SIUMCR for CAN */
	#define CONFIG_SYS_SIUMCR (SIUMCR_DBGC11 \| SIUMCR_DBPC00 \| SIUMCR_MLRC01)
	#endif /* CONFIG_CAN_DRIVER */

	/*-----------------------------------------------------------------------
	* TBSCR - Time Base Status and Control 11-26
	*-----------------------------------------------------------------------
	* Clear Reference Interrupt Status, Timebase freezing enabled
	*/
	#define CONFIG_SYS_TBSCR (TBSCR_REFA \| TBSCR_REFB \| TBSCR_TBF)

	/*-----------------------------------------------------------------------
	* RTCSC - Real-Time Clock Status and Control Register 11-27
	*-----------------------------------------------------------------------
	*/
	#define CONFIG_SYS_RTCSC (RTCSC_SEC \| RTCSC_ALR \| RTCSC_RTF\| RTCSC_RTE)

	/*-----------------------------------------------------------------------
	* PISCR - Periodic Interrupt Status and Control 11-31
	*-----------------------------------------------------------------------
	* Clear Periodic Interrupt Status, Interrupt Timer freezing enabled
	*/
	#define CONFIG_SYS_PISCR (PISCR_PS \| PISCR_PITF)

	/*-----------------------------------------------------------------------
	* PLPRCR - PLL, Low-Power, and Reset Control Register 15-30
	*-----------------------------------------------------------------------
	* Reset PLL lock status sticky bit, timer expired status bit and timer
	* interrupt status bit
	*/
	#define CONFIG_SYS_PLPRCR (PLPRCR_SPLSS \| PLPRCR_TEXPS \| PLPRCR_TMIST)

	/*-----------------------------------------------------------------------
	* SCCR - System Clock and reset Control Register 15-27
	*-----------------------------------------------------------------------
	* Set clock output, timebase and RTC source and divider,
	* power management and some other internal clocks
	*/
	#define SCCR_MASK SCCR_EBDF11
	#define CONFIG_SYS_SCCR (SCCR_COM00 \| SCCR_DFSYNC00 \| SCCR_DFBRG00 \| \
	SCCR_DFNL000 \| SCCR_DFNH000 \| SCCR_DFLCD000 \| \
	SCCR_DFALCD00)

	/*-----------------------------------------------------------------------
	* PCMCIA stuff
	*-----------------------------------------------------------------------
	*
	*/
	#define CONFIG_SYS_PCMCIA_MEM_ADDR (0xE0000000)
	#define CONFIG_SYS_PCMCIA_MEM_SIZE ( 64 << 20 )
	#define CONFIG_SYS_PCMCIA_DMA_ADDR (0xE4000000)
	#define CONFIG_SYS_PCMCIA_DMA_SIZE ( 64 << 20 )
	#define CONFIG_SYS_PCMCIA_ATTRB_ADDR (0xE8000000)
	#define CONFIG_SYS_PCMCIA_ATTRB_SIZE ( 64 << 20 )
	#define CONFIG_SYS_PCMCIA_IO_ADDR (0xEC000000)
	#define CONFIG_SYS_PCMCIA_IO_SIZE ( 64 << 20 )

	/*-----------------------------------------------------------------------
	* IDE/ATA stuff (Supports IDE harddisk on PCMCIA Adapter)
	*-----------------------------------------------------------------------
	*/

	#define CONFIG_IDE_PREINIT 1 /* Use preinit IDE hook */
	#define CONFIG_IDE_8xx_PCCARD 1 /* Use IDE with PC Card Adapter */

	#undef CONFIG_IDE_8xx_DIRECT /* Direct IDE not supported */
	#undef CONFIG_IDE_LED /* LED for ide not supported */
	#undef CONFIG_IDE_RESET /* reset for ide not supported */

	#define CONFIG_SYS_IDE_MAXBUS 1 /* max. 1 IDE bus */
	#define CONFIG_SYS_IDE_MAXDEVICE 1 /* max. 1 drive per IDE bus */

	#define CONFIG_SYS_ATA_IDE0_OFFSET 0x0000

	#define CONFIG_SYS_ATA_BASE_ADDR CONFIG_SYS_PCMCIA_MEM_ADDR

	/* Offset for data I/O */
	#define CONFIG_SYS_ATA_DATA_OFFSET (CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)

	/* Offset for normal register accesses */
	#define CONFIG_SYS_ATA_REG_OFFSET (2 * CONFIG_SYS_PCMCIA_MEM_SIZE + 0x320)

	/* Offset for alternate registers */
	#define CONFIG_SYS_ATA_ALT_OFFSET 0x0100

	/*-----------------------------------------------------------------------
	*
	*-----------------------------------------------------------------------
	*
	*/
	#define CONFIG_SYS_DER 0

	/*
	* Init Memory Controller:
	*
	* BR0/1 and OR0/1 (FLASH)
	*/

	#define FLASH_BASE0_PRELIM 0x40000000 /* FLASH bank #0 */
	#define FLASH_BASE1_PRELIM 0x60000000 /* FLASH bank #0 */

	/* used to re-map FLASH both when starting from SRAM or FLASH:
	* restrict access enough to keep SRAM working (if any)
	* but not too much to meddle with FLASH accesses
	*/
	#define CONFIG_SYS_REMAP_OR_AM 0x80000000 /* OR addr mask */
	#define CONFIG_SYS_PRELIM_OR_AM 0xE0000000 /* OR addr mask */

	/*
	* FLASH timing:
	*/
	#define CONFIG_SYS_OR_TIMING_FLASH (OR_ACS_DIV1 \| OR_TRLX \| OR_CSNT_SAM \| \
	OR_SCY_3_CLK \| OR_EHTR \| OR_BI)

	#define CONFIG_SYS_OR0_REMAP (CONFIG_SYS_REMAP_OR_AM \| CONFIG_SYS_OR_TIMING_FLASH)
	#define CONFIG_SYS_OR0_PRELIM (CONFIG_SYS_PRELIM_OR_AM \| CONFIG_SYS_OR_TIMING_FLASH)
	#define CONFIG_SYS_BR0_PRELIM ((FLASH_BASE0_PRELIM & BR_BA_MSK) \| BR_V )

	#define CONFIG_SYS_OR1_REMAP CONFIG_SYS_OR0_REMAP
	#define CONFIG_SYS_OR1_PRELIM CONFIG_SYS_OR0_PRELIM
	#define CONFIG_SYS_BR1_PRELIM ((FLASH_BASE1_PRELIM & BR_BA_MSK) \| BR_V )

	/*
	* BR2/3 and OR2/3 (SDRAM)
	*
	*/
	#define SDRAM_BASE2_PRELIM 0x00000000 /* SDRAM bank #0 */
	#define SDRAM_BASE3_PRELIM 0x20000000 /* SDRAM bank #1 */
	#define SDRAM_MAX_SIZE 0x04000000 /* max 64 MB per bank */

	/* SDRAM timing: Multiplexed addresses, GPL5 output to GPL5_A (don't care) */
	#define CONFIG_SYS_OR_TIMING_SDRAM 0x00000A00

	#define CONFIG_SYS_OR2_PRELIM (CONFIG_SYS_PRELIM_OR_AM \| CONFIG_SYS_OR_TIMING_SDRAM )
	#define CONFIG_SYS_BR2_PRELIM ((SDRAM_BASE2_PRELIM & BR_BA_MSK) \| BR_MS_UPMA \| BR_V )

	#ifndef CONFIG_CAN_DRIVER
	#define CONFIG_SYS_OR3_PRELIM CONFIG_SYS_OR2_PRELIM
	#define CONFIG_SYS_BR3_PRELIM ((SDRAM_BASE3_PRELIM & BR_BA_MSK) \| BR_MS_UPMA \| BR_V )
	#else /* CAN uses CS3#, so we can have only one SDRAM bank anyway */
	#define CONFIG_SYS_CAN_BASE 0xC0000000 /* CAN mapped at 0xC0000000 */
	#define CONFIG_SYS_CAN_OR_AM 0xFFFF8000 /* 32 kB address mask */
	#define CONFIG_SYS_OR3_CAN (CONFIG_SYS_CAN_OR_AM \| OR_G5LA \| OR_BI)
	#define CONFIG_SYS_BR3_CAN ((CONFIG_SYS_CAN_BASE & BR_BA_MSK) \| \
	BR_PS_8 \| BR_MS_UPMB \| BR_V )
	#endif /* CONFIG_CAN_DRIVER */

	/*
	* Memory Periodic Timer Prescaler
	*
	* The Divider for PTA (refresh timer) configuration is based on an
	* example SDRAM configuration (64 MBit, one bank). The adjustment to
	* the number of chip selects (NCS) and the actually needed refresh
	* rate is done by setting MPTPR.
	*
	* PTA is calculated from
	* PTA = (gclk * Trefresh) / ((2 ^ (2 * DFBRG)) * PTP * NCS)
	*
	* gclk CPU clock (not bus clock!)
	* Trefresh Refresh cycle * 4 (four word bursts used)
	*
	* 4096 Rows from SDRAM example configuration
	* 1000 factor s -> ms
	* 32 PTP (pre-divider from MPTPR) from SDRAM example configuration
	* 4 Number of refresh cycles per period
	* 64 Refresh cycle in ms per number of rows
	* --------------------------------------------
	* Divider = 4096 * 32 * 1000 / (4 * 64) = 512000
	*
	* 50 MHz => 50.000.000 / Divider = 98
	* 66 Mhz => 66.000.000 / Divider = 129
	* 80 Mhz => 80.000.000 / Divider = 156
	*/

	#define CONFIG_SYS_PTA_PER_CLK ((4096 * 32 * 1000) / (4 * 64))
	#define CONFIG_SYS_MAMR_PTA 98

	/*
	* For 16 MBit, refresh rates could be 31.3 us
	* (= 64 ms / 2K = 125 / quad bursts).
	* For a simpler initialization, 15.6 us is used instead.
	*
	* #define CONFIG_SYS_MPTPR_2BK_2K MPTPR_PTP_DIV32 for 2 banks
	* #define CONFIG_SYS_MPTPR_1BK_2K MPTPR_PTP_DIV64 for 1 bank
	*/
	#define CONFIG_SYS_MPTPR_2BK_4K MPTPR_PTP_DIV16 /* setting for 2 banks */
	#define CONFIG_SYS_MPTPR_1BK_4K MPTPR_PTP_DIV32 /* setting for 1 bank */

	/* refresh rate 7.8 us (= 64 ms / 8K = 31.2 / quad bursts) for 256 MBit */
	#define CONFIG_SYS_MPTPR_2BK_8K MPTPR_PTP_DIV8 /* setting for 2 banks */
	#define CONFIG_SYS_MPTPR_1BK_8K MPTPR_PTP_DIV16 /* setting for 1 bank */

	/*
	* MAMR settings for SDRAM
	*/

	/* 8 column SDRAM */
	#define CONFIG_SYS_MAMR_8COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) \| MAMR_PTAE \| \
	MAMR_AMA_TYPE_0 \| MAMR_DSA_1_CYCL \| MAMR_G0CLA_A11 \| \
	MAMR_RLFA_1X \| MAMR_WLFA_1X \| MAMR_TLFA_4X)
	/* 9 column SDRAM */
	#define CONFIG_SYS_MAMR_9COL ((CONFIG_SYS_MAMR_PTA << MAMR_PTA_SHIFT) \| MAMR_PTAE \| \
	MAMR_AMA_TYPE_1 \| MAMR_DSA_1_CYCL \| MAMR_G0CLA_A10 \| \
	MAMR_RLFA_1X \| MAMR_WLFA_1X \| MAMR_TLFA_4X)

	/* pass open firmware flat tree */
	#define CONFIG_OF_LIBFDT 1
	#define CONFIG_OF_BOARD_SETUP 1
	#define CONFIG_HWCONFIG 1

	#endif /* __CONFIG_H */