blob: fa64a688a44af63ee7e20e6c8f29d8be090fa478 [file] [log] [blame] [edit]
/*
* Configuration settings for the Sentec Cobra Board.
*
* (C) Copyright 2003 Josef Baumgartner <josef.baumgartner@telex.de>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/*
* configuration for ASTRO "Urmel" board.
* Originating from Cobra5272 configuration, messed up by
* Wolfgang Wegner <w.wegner@astro-kom.de>
* Please do not bother the original author with bug reports
* concerning this file.
*/
#ifndef _CONFIG_ASTRO_MCF5373L_H
#define _CONFIG_ASTRO_MCF5373L_H
#include <linux/stringify.h>
/*
* set the card type to actually compile for; either of
* the possibilities listed below has to be used!
*/
#define CONFIG_ASTRO_V532 1
#if CONFIG_ASTRO_V532
#define ASTRO_ID 0xF8
#elif CONFIG_ASTRO_V512
#define ASTRO_ID 0xFA
#elif CONFIG_ASTRO_TWIN7S2
#define ASTRO_ID 0xF9
#elif CONFIG_ASTRO_V912
#define ASTRO_ID 0xFC
#elif CONFIG_ASTRO_COFDMDUOS2
#define ASTRO_ID 0xFB
#else
#error No card type defined!
#endif
/*
* Define processor
* possible values for Urmel board: only Coldfire M5373 processor supported
* (please do not change)
*/
/* it seems not clear yet which processor defines we should use */
#define CONFIG_MCF537x /* define processor family */
#define CONFIG_MCF532x /* define processor family */
#define CONFIG_M5373 /* define processor type */
#define CONFIG_ASTRO5373L /* define board type */
/* Command line configuration */
#include <config_cmd_default.h>
/*
* CONFIG_RAM defines if u-boot is loaded via BDM (or started from
* a different bootloader that has already performed RAM setup) or
* started directly from flash, which is the regular case for production
* boards.
*/
#ifdef CONFIG_RAM
#define CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_SYS_TEXT_BASE 0x40020000
#define ENABLE_JFFS 0
#else
#define CONFIG_SYS_TEXT_BASE 0x00000000
#define ENABLE_JFFS 1
#endif
/* Define which commmands should be available at u-boot command prompt */
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
#define CONFIG_CMD_ELF
#define CONFIG_CMD_FLASH
#define CONFIG_CMD_I2C
#define CONFIG_CMD_MEMORY
#define CONFIG_CMD_MISC
#define CONFIG_CMD_XIMG
#undef CONFIG_CMD_NET
#undef CONFIG_CMD_NFS
#if ENABLE_JFFS
#define CONFIG_CMD_JFFS2
#endif
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_LOADS
#define CONFIG_CMD_LOADB
#define CONFIG_CMD_FPGA
#define CONFIG_CMD_FPGA_LOADMK
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_MCFRTC
#undef RTC_DEBUG
/* Timer */
#define CONFIG_MCFTMR
#undef CONFIG_MCFPIT
/* I2C */
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_FSL
#define CONFIG_SYS_FSL_I2C_SPEED 80000
#define CONFIG_SYS_FSL_I2C_SLAVE 0x7F
#define CONFIG_SYS_FSL_I2C_OFFSET 0x58000
#define CONFIG_SYS_IMMR CONFIG_SYS_MBAR
/*
* Defines processor clock - important for correct timings concerning serial
* interface etc.
*/
#define CONFIG_SYS_CLK 80000000
#define CONFIG_SYS_CPU_CLK (CONFIG_SYS_CLK * 3)
#define CONFIG_SYS_SDRAM_SIZE 32 /* SDRAM size in MB */
#define CONFIG_SYS_CORE_SRAM_SIZE 0x8000
#define CONFIG_SYS_CORE_SRAM 0x80000000
#define CONFIG_SYS_UNIFY_CACHE
/*
* Define baudrate for UART1 (console output, tftp, ...)
* default value of CONFIG_BAUDRATE for Sentec board: 19200 baud
* CONFIG_SYS_BAUDRATE_TABLE defines values that can be selected
* in u-boot command interface
*/
#define CONFIG_BAUDRATE 115200
#define CONFIG_MCFUART
#define CONFIG_SYS_UART_PORT (2)
#define CONFIG_SYS_UART2_ALT3_GPIO
/*
* Watchdog configuration; Watchdog is disabled for running from RAM
* and set to highest possible value else. Beware there is no check
* in the watchdog code to validate the timeout value set here!
*/
#ifndef CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_WATCHDOG
#define CONFIG_WATCHDOG_TIMEOUT 3355 /* timeout in milliseconds */
#endif
/*
* Configuration for environment
* Environment is located in the last sector of the flash
*/
#ifndef CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_ENV_OFFSET 0x1FF8000
#define CONFIG_ENV_SECT_SIZE 0x8000
#define CONFIG_ENV_IS_IN_FLASH 1
#else
/*
* environment in RAM - This is used to use a single PC-based application
* to load an image, load U-Boot, load an environment and then start U-Boot
* to execute the commands from the environment. Feedback is done via setting
* and reading memory locations.
*/
#define CONFIG_ENV_ADDR 0x40060000
#define CONFIG_ENV_SECT_SIZE 0x8000
#define CONFIG_ENV_IS_IN_FLASH 1
#endif
/* here we put our FPGA configuration... */
#define CONFIG_MISC_INIT_R 1
/* Define user parameters that have to be customized most likely */
/* AUTOBOOT settings - booting images automatically by u-boot after power on */
/*
* used for autoboot, delay in seconds u-boot will wait before starting
* defined (auto-)boot command, setting to -1 disables delay, setting to
* 0 will too prevent access to u-boot command interface: u-boot then has
* to be reflashed
* beware - watchdog is not serviced during autoboot delay time!
*/
#ifdef CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_BOOTDELAY 1
#else
#define CONFIG_BOOTDELAY 1
#endif
/*
* The following settings will be contained in the environment block ; if you
* want to use a neutral environment all those settings can be manually set in
* u-boot: 'set' command
*/
#define CONFIG_EXTRA_ENV_SETTINGS \
"loaderversion=11\0" \
"card_id="__stringify(ASTRO_ID)"\0" \
"alterafile=0\0" \
"xilinxfile=0\0" \
"xilinxload=imxtract 0x540000 $xilinxfile 0x41000000&&"\
"fpga load 0 0x41000000 $filesize\0" \
"alteraload=imxtract 0x6c0000 $alterafile 0x41000000&&"\
"fpga load 1 0x41000000 $filesize\0" \
"env_default=1\0" \
"env_check=if test $env_default -eq 1;"\
" then setenv env_default 0;saveenv;fi\0"
/*
* "update" is a non-standard command that has to be supplied
* by external update.c; This is not included in mainline because
* it needs non-blocking CFI routines.
*/
#ifdef CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_BOOTCOMMAND "" /* no autoboot in this case */
#else
#if CONFIG_ASTRO_V532
#define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\
"run xilinxload&&run alteraload&&bootm 0x80000;"\
"update;reset"
#else
#define CONFIG_BOOTCOMMAND "protect off 0x80000 0x1ffffff;run env_check;"\
"run xilinxload&&bootm 0x80000;update;reset"
#endif
#endif
/* default bootargs that are considered during boot */
#define CONFIG_BOOTARGS " console=ttyS2,115200 rootfstype=romfs"\
" loaderversion=$loaderversion"
#define CONFIG_SYS_PROMPT "URMEL > "
/* default RAM address for user programs */
#define CONFIG_SYS_LOAD_ADDR 0x20000
#define CONFIG_SYS_LONGHELP
#if (CONFIG_COMMANDS & CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024
#else
#define CONFIG_SYS_CBSIZE 256
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_FPGA_COUNT 1
#define CONFIG_FPGA
#define CONFIG_FPGA_XILINX
#define CONFIG_FPGA_SPARTAN3
#define CONFIG_FPGA_ALTERA
#define CONFIG_FPGA_CYCLON2
#define CONFIG_SYS_FPGA_PROG_FEEDBACK
#define CONFIG_SYS_FPGA_WAIT 1000
/* End of user parameters to be customized */
/* Defines memory range for test */
#define CONFIG_SYS_MEMTEST_START 0x40020000
#define CONFIG_SYS_MEMTEST_END 0x41ffffff
/*
* Low Level Configuration Settings
* (address mappings, register initial values, etc.)
* You should know what you are doing if you make changes here.
*/
/* Base register address */
#define CONFIG_SYS_MBAR 0xFC000000 /* Register Base Addrs */
/* System Conf. Reg. & System Protection Reg. */
#define CONFIG_SYS_SCR 0x0003;
#define CONFIG_SYS_SPR 0xffff;
/*
* Definitions for initial stack pointer and data area (in internal SRAM)
*/
#define CONFIG_SYS_INIT_RAM_ADDR 0x80000000
#define CONFIG_SYS_INIT_RAM_SIZE 0x8000
#define CONFIG_SYS_INIT_RAM_CTRL 0x221
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
/*
* Start addresses for the final memory configuration
* (Set up by the startup code)
* for MCF5373, the allowable range is 0x40000000 to 0x7FF00000
*/
#define CONFIG_SYS_SDRAM_BASE 0x40000000
/*
* Chipselect bank definitions
*
* CS0 - Flash 32MB (first 16MB)
* CS1 - Flash 32MB (second half)
* CS2 - FPGA
* CS3 - FPGA
* CS4 - unused
* CS5 - unused
*/
#define CONFIG_SYS_CS0_BASE 0
#define CONFIG_SYS_CS0_MASK 0x00ff0001
#define CONFIG_SYS_CS0_CTRL 0x00001fc0
#define CONFIG_SYS_CS1_BASE 0x01000000
#define CONFIG_SYS_CS1_MASK 0x00ff0001
#define CONFIG_SYS_CS1_CTRL 0x00001fc0
#define CONFIG_SYS_CS2_BASE 0x20000000
#define CONFIG_SYS_CS2_MASK 0x00ff0001
#define CONFIG_SYS_CS2_CTRL 0x0000fec0
#define CONFIG_SYS_CS3_BASE 0x21000000
#define CONFIG_SYS_CS3_MASK 0x00ff0001
#define CONFIG_SYS_CS3_CTRL 0x0000fec0
#define CONFIG_SYS_FLASH_BASE 0x00000000
#ifdef CONFIG_MONITOR_IS_IN_RAM
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_TEXT_BASE
#else
/* This is mainly used during relocation in start.S */
#define CONFIG_SYS_MONITOR_BASE (CONFIG_SYS_FLASH_BASE + 0x400)
#endif
/* Reserve 256 kB for Monitor */
#define CONFIG_SYS_MONITOR_LEN (256 << 10)
#define CONFIG_SYS_BOOTPARAMS_LEN (64 * 1024)
/* Reserve 128 kB for malloc() */
#define CONFIG_SYS_MALLOC_LEN (128 << 10)
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization ??
*/
#define CONFIG_SYS_BOOTMAPSZ (CONFIG_SYS_SDRAM_BASE + \
(CONFIG_SYS_SDRAM_SIZE << 20))
/* FLASH organization */
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 259
#define CONFIG_SYS_FLASH_ERASE_TOUT 1000
#define CONFIG_SYS_FLASH_CFI 1
#define CONFIG_FLASH_CFI_DRIVER 1
#define CONFIG_SYS_FLASH_SIZE 0x2000000
#define CONFIG_SYS_FLASH_PROTECTION 1
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1
#define CONFIG_SYS_FLASH_CFI_NONBLOCK 1
#if ENABLE_JFFS
/* JFFS Partition offset set */
#define CONFIG_SYS_JFFS2_FIRST_BANK 0
#define CONFIG_SYS_JFFS2_NUM_BANKS 1
/* 512k reserved for u-boot */
#define CONFIG_SYS_JFFS2_FIRST_SECTOR 0x40
#endif
/* Cache Configuration */
#define CONFIG_SYS_CACHELINE_SIZE 16
#define ICACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 8)
#define DCACHE_STATUS (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_INIT_RAM_SIZE - 4)
#define CONFIG_SYS_ICACHE_INV (CF_CACR_CINVA)
#define CONFIG_SYS_CACHE_ACR0 (CONFIG_SYS_SDRAM_BASE | \
CF_ADDRMASK(CONFIG_SYS_SDRAM_SIZE) | \
CF_ACR_EN | CF_ACR_SM_ALL)
#define CONFIG_SYS_CACHE_ICACR (CF_CACR_EC | CF_CACR_CINVA | \
CF_CACR_DCM_P)
#endif /* _CONFIG_ASTRO_MCF5373L_H */