blob: 72eafc5699b57f5dc578fad441a733f4a66b21e5 [file] [log] [blame] [edit]
/*
* U-boot - Configuration file for cm-bf548 board
*/
#ifndef __CONFIG_CM_BF548_H__
#define __CONFIG_CM_BF548_H__
#include <asm/config-pre.h>
/*
* Processor Settings
*/
#define CONFIG_BFIN_CPU bf548-0.0
#define CONFIG_BFIN_BOOT_MODE BFIN_BOOT_PARA
/*
* Clock Settings
* CCLK = (CLKIN * VCO_MULT) / CCLK_DIV
* SCLK = (CLKIN * VCO_MULT) / SCLK_DIV
*/
/* CONFIG_CLKIN_HZ is any value in Hz */
#define CONFIG_CLKIN_HZ 25000000
/* CLKIN_HALF controls the DF bit in PLL_CTL 0 = CLKIN */
/* 1 = CLKIN / 2 */
#define CONFIG_CLKIN_HALF 0
/* PLL_BYPASS controls the BYPASS bit in PLL_CTL 0 = do not bypass */
/* 1 = bypass PLL */
#define CONFIG_PLL_BYPASS 0
/* VCO_MULT controls the MSEL (multiplier) bits in PLL_CTL */
/* Values can range from 0-63 (where 0 means 64) */
#define CONFIG_VCO_MULT 21
/* CCLK_DIV controls the core clock divider */
/* Values can be 1, 2, 4, or 8 ONLY */
#define CONFIG_CCLK_DIV 1
/* SCLK_DIV controls the system clock divider */
/* Values can range from 1-15 */
#define CONFIG_SCLK_DIV 4
/* Decrease core voltage */
#define CONFIG_VR_CTL_VAL (VLEV_115 | GAIN_20 | FREQ_1000)
/*
* Memory Settings
*/
#define CONFIG_MEM_ADD_WDTH 10
#define CONFIG_MEM_SIZE 64
#define CONFIG_EBIU_DDRCTL0_VAL 0x218A83FE
#define CONFIG_EBIU_DDRCTL1_VAL 0x20022222
#define CONFIG_EBIU_DDRCTL2_VAL 0x00000021
/* Default bank mapping:
* Async Bank 0 - 32MB Burst Flash
* Async Bank 1 - Ethernet
* Async Bank 2 - Nothing
* Async Bank 3 - Nothing
*/
#define CONFIG_EBIU_AMGCTL_VAL 0xFF
#define CONFIG_EBIU_AMBCTL0_VAL 0x7BB07BB0
#define CONFIG_EBIU_AMBCTL1_VAL 0xFFC27BB0
#define CONFIG_EBIU_FCTL_VAL (BCLK_4)
#define CONFIG_EBIU_MODE_VAL (B0MODE_FLASH)
#define CONFIG_SYS_MONITOR_LEN (512 * 1024)
#define CONFIG_SYS_MALLOC_LEN (640 * 1024)
/*
* Network Settings
*/
#define ADI_CMDS_NETWORK 1
#define CONFIG_SMC911X 1
#define CONFIG_SMC911X_BASE 0x24000000
#define CONFIG_SMC911X_16_BIT
#define CONFIG_HOSTNAME cm-bf548
/* Uncomment next line to use fixed MAC address */
/* #define CONFIG_ETHADDR 02:80:ad:24:31:91 */
/*
* Flash Settings
*/
#define CONFIG_FLASH_CFI_DRIVER
#define CONFIG_SYS_FLASH_BASE 0x20000000
#define CONFIG_SYS_FLASH_CFI
#define CONFIG_SYS_FLASH_PROTECTION
#define CONFIG_SYS_MAX_FLASH_BANKS 1
#define CONFIG_SYS_MAX_FLASH_SECT 259
/*
* Env Storage Settings
*/
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_ADDR 0x20008000
#define CONFIG_ENV_OFFSET 0x8000
#define CONFIG_ENV_SIZE 0x8000
#define CONFIG_ENV_IS_EMBEDDED_IN_LDR
/*
* I2C Settings
*/
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_ADI
/*
* Misc Settings
*/
#define CONFIG_BAUDRATE 115200
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_RTC_BFIN
#define CONFIG_UART_CONSOLE 1
#define CONFIG_BOOTCOMMAND "run flashboot"
#define FLASHBOOT_ENV_SETTINGS "flashboot=bootm 0x20040000\0"
#define CONFIG_ADI_GPIO2
#ifndef __ADSPBF542__
/* Don't waste time transferring a logo over the UART */
# if (CONFIG_BFIN_BOOT_MODE != BFIN_BOOT_UART)
# define CONFIG_VIDEO
# define EASYLOGO_HEADER <asm/bfin_logo_230x230_gzip.h>
# endif
# define CONFIG_DEB_DMA_URGENT
#endif
/* Define if want to do post memory test */
#undef CONFIG_POST
#ifdef CONFIG_POST
#define FLASH_START_POST_BLOCK 11 /* Should > = 11 */
#define FLASH_END_POST_BLOCK 71 /* Should < = 71 */
#endif
/*
* Pull in common ADI header for remaining command/environment setup
*/
#include <configs/bfin_adi_common.h>
#endif