blob: 0f4bd91c645d0be4177fa7cf5855710b1e46cce1 [file] [log] [blame] [edit]
/*
* Copyright (C) 2008, Guennadi Liakhovetski <lg@denx.de>
*
* Configuration settings for the MX31ADS Freescale board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/arch/imx-regs.h>
/* High Level Configuration Options */
#define CONFIG_MX31 1 /* This is a mx31 */
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_SYS_TEXT_BASE 0xA0000000
#define CONFIG_MACH_TYPE MACH_TYPE_MX31ADS
/*
* Disabled for now due to build problems under Debian and a significant increase
* in the final file size: 144260 vs. 109536 Bytes.
*/
#if 0
#define CONFIG_OF_LIBFDT 1
#define CONFIG_FIT 1
#define CONFIG_FIT_VERBOSE 1
#endif
#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS 1
#define CONFIG_INITRD_TAG 1
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 128 * 1024)
/*
* Hardware drivers
*/
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART1_BASE
#define CONFIG_HARD_SPI 1
#define CONFIG_MXC_SPI 1
#define CONFIG_DEFAULT_SPI_BUS 1
#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
#define CONFIG_MXC_GPIO
/* PMIC Controller */
#define CONFIG_POWER
#define CONFIG_POWER_SPI
#define CONFIG_POWER_FSL
#define CONFIG_FSL_PMIC_BUS 1
#define CONFIG_FSL_PMIC_CS 0
#define CONFIG_FSL_PMIC_CLK 1000000
#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
#define CONFIG_FSL_PMIC_BITLEN 32
#define CONFIG_RTC_MC13XXX
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
/***********************************************************
* Command definition
***********************************************************/
#include <config_cmd_default.h>
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_SPI
#define CONFIG_CMD_DATE
#define CONFIG_BOOTDELAY 3
#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"uboot_addr=0xa0000000\0" \
"uboot=mx31ads/u-boot.bin\0" \
"kernel=mx31ads/uImage\0" \
"nfsroot=/opt/eldk/arm\0" \
"bootargs_base=setenv bootargs console=ttymxc0,115200\0" \
"bootargs_nfs=setenv bootargs ${bootargs} root=/dev/nfs " \
"ip=dhcp nfsroot=${serverip}:${nfsroot},v3,tcp\0" \
"bootcmd=run bootcmd_net\0" \
"bootcmd_net=run bootargs_base bootargs_nfs; " \
"tftpboot ${loadaddr} ${kernel}; bootm\0" \
"prg_uboot=tftpboot ${loadaddr} ${uboot}; " \
"protect off ${uboot_addr} 0xa003ffff; " \
"erase ${uboot_addr} 0xa003ffff; " \
"cp.b ${loadaddr} ${uboot_addr} ${filesize}; " \
"setenv filesize; saveenv\0"
#define CONFIG_CS8900
#define CONFIG_CS8900_BASE 0xb4020300
#define CONFIG_CS8900_BUS16 1 /* follow the Linux driver */
/*
* The MX31ADS board seems to have a hardware "peculiarity" confirmed under
* U-Boot, RedBoot and Linux: the ethernet Rx signal is reaching the CS8900A
* controller inverted. The controller is capable of detecting and correcting
* this, but it needs 4 network packets for that. Which means, at startup, you
* will not receive answers to the first 4 packest, unless there have been some
* broadcasts on the network, or your board is on a hub. Reducing the ARP
* timeout from default 5 seconds to 200ms we speed up the initial TFTP
* transfer, should the user wish one, significantly.
*/
#define CONFIG_ARP_TIMEOUT 200UL
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x10000
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_CMDLINE_EDITING 1
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 CSD0_BASE
#define PHYS_SDRAM_1_SIZE (128 * 1024 * 1024)
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM_1
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - \
GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + \
CONFIG_SYS_GBL_DATA_OFFSET)
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
#define CONFIG_SYS_FLASH_BASE CS0_BASE
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 262 /* max number of sectors on one chip */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE /* Monitor at beginning of flash */
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256KiB */
#define CONFIG_ENV_IS_IN_FLASH 1
#define CONFIG_ENV_SECT_SIZE (128 * 1024)
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE + CONFIG_SYS_MONITOR_LEN)
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
/*-----------------------------------------------------------------------
* CFI FLASH driver setup
*/
#define CONFIG_SYS_FLASH_CFI 1 /* Flash memory is CFI compliant */
#define CONFIG_FLASH_CFI_DRIVER 1 /* Use drivers/cfi_flash.c */
#define CONFIG_FLASH_SPANSION_S29WS_N 1 /* A non-standard buffered write algorithm */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* Use buffered writes (~10x faster) */
#define CONFIG_SYS_FLASH_PROTECTION 1 /* Use hardware sector protection */
/*
* JFFS2 partitions
*/
#undef CONFIG_CMD_MTDPARTS
#define CONFIG_JFFS2_DEV "nor0"
#endif /* __CONFIG_H */