| /* |
| * Copyright (C) 2015 Hardkernel Co,. Ltd |
| * Dongjin Kim <tobetter@gmail.com> |
| * |
| * Configuration settings for ODROID-C2 (AMLogic S905) board, |
| * cloned from include/configs/gxb_p200_v1.h |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #ifndef __ODROID_C2_H__ |
| #define __ODROID_C2_H__ |
| |
| #include <linux/sizes.h> |
| |
| #define CONFIG_MACH_ODROIDC2 1 |
| |
| #ifndef __SUSPEND_FIRMWARE__ |
| #include <asm/arch/cpu.h> |
| #endif /* for compile problem of A53 and m3 */ |
| |
| #define CONFIG_SYS_GENERIC_BOARD 1 |
| #ifndef __SUSPEND_FIRMWARE__ |
| #ifndef CONFIG_AML_MESON |
| #warning "include warning" |
| #endif |
| #endif /* for compile problem of A53 and m3 */ |
| |
| /* CPU */ |
| /* Clock rnage : 600~1800MHz, should be multiple of 24 */ |
| #define CONFIG_CPU_CLK 1536 |
| |
| /* SMP Definitinos */ |
| #define CPU_RELEASE_ADDR secondary_boot_func |
| |
| /* DDR */ |
| #define CONFIG_DDR_SIZE (1024 + 512) // MB |
| |
| /* Clock range : 384~1200MHz, should be multiple of 24 */ |
| #define CONFIG_DDR_CLK 912 |
| #define CONFIG_DDR_TYPE CONFIG_DDR_TYPE_DDR3 |
| |
| /* DDR channel setting, please refer hardware design. |
| * CONFIG_DDR0_RANK0_ONLY : one channel |
| * CONFIG_DDR0_RANK01_SAME : one channel use two rank with same setting |
| * CONFIG_DDR01_SHARE_AC : two channels |
| */ |
| #define CONFIG_DDR_CHANNEL_SET CONFIG_DDR0_RANK01_SAME |
| #define CONFIG_DDR_FULL_TEST 0 // 1 for ddr full test |
| #define CONFIG_NR_DRAM_BANKS 1 |
| |
| /* DDR power saving */ |
| #define CONFIG_DDR_ZQ_POWER_DOWN 1 |
| #define CONFIG_DDR_POWER_DOWN_PHY_VREF 1 |
| |
| /* DDR detection */ |
| #define CONFIG_DDR_SIZE_AUTO_DETECT 1 |
| |
| /* Platform power init config */ |
| #define CONFIG_PLATFORM_POWER_INIT |
| #define CONFIG_VCCK_INIT_VOLTAGE 1100 |
| #define CONFIG_VDDEE_INIT_VOLTAGE 1050 // voltage for power up |
| #define CONFIG_VDDEE_SLEEP_VOLTAGE 850 // voltage for suspend |
| |
| /* CEC */ |
| #define CONFIG_CEC_OSD_NAME "ODROID-C2" |
| #define CONFIG_CEC_WAKEUP |
| |
| /* Serial config */ |
| #define CONFIG_CONS_INDEX 2 |
| #define CONFIG_BAUDRATE 115200 |
| #define CONFIG_AML_MESON_SERIAL 1 |
| #define CONFIG_SERIAL_MULTI 1 |
| //for detect remote key |
| #define CONFIG_IR_REMOTE 1 |
| //Enable ir remote wake up for bl30 |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_CNT 3 |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL1 0XE51AFB04 //amlogic tv ir --- power |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL2 0XBB44FB04 //amlogic tv ir --- ch+ |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL3 0xF20DFE01 //amlogic tv ir --- ch- |
| #define CONFIG_IR_REMOTE_POWER_UP_KEY_VAL4 0xFFFFFFFF |
| |
| #define CONFIG_BOOTDELAY 1 // Seconds |
| |
| /* args/envs */ |
| #define CONFIG_SYS_MAXARGS 64 |
| |
| #define CONFIG_EXTRA_ENV_SETTINGS \ |
| "boardname=ODROIDC2\0" \ |
| "loadaddr=0x10800000\0" \ |
| "dtb_mem_addr=0x1000000\0" \ |
| "fdt_high=0x20000000\0" \ |
| "display_layer=osd1\0" \ |
| "fb_addr=0x3d800000\0" \ |
| "outputmode=720p60hz\0" \ |
| "bootargs=root=/dev/mmcblk0p1 init=/sbin/init console=ttyS0,115200 logo=${display_layer},loaded,${fb_addr},${outputmode} vout=${outputmode}, hdmimode=720p60hz androidboot.hardware=odroidc2 earlyprintk=aml-uart,0xc81004c0\0" \ |
| "bootcmd=ext4load mmc 0 ${loadaddr} boot.img; bootm ${loadaddr}\0" |
| |
| #define CONFIG_PREBOOT |
| #define CONFIG_BOOTCOMMAND |
| |
| //#define CONFIG_ENV_IS_NOWHERE 1 |
| #define CONFIG_ENV_SIZE (64 * SZ_1K) /* 32kB */ |
| #define CONFIG_ENV_OFFSET (1024 * SZ_1K) /* FIXME: should be |
| close to U-boot image |
| size to save space */ |
| #define CONFIG_FIT 1 |
| #define CONFIG_OF_LIBFDT 1 |
| #define CONFIG_ANDROID_BOOT_IMAGE 1 |
| #define CONFIG_ANDROID_IMG 1 |
| #define CONFIG_SYS_BOOTM_LEN (64 << 20) /* Increase max gunzip size*/ |
| |
| /* Support commands */ |
| #define CONFIG_CMD_SAVEENV 1 |
| #define CONFIG_CMD_CACHE 1 |
| #define CONFIG_CMD_BOOTI 1 |
| #define CONFIG_CMD_EFUSE 1 |
| //#define CONFIG_CMD_I2C 1 |
| #define CONFIG_CMD_MEMORY 1 |
| #define CONFIG_CMD_FAT 1 |
| #define CONFIG_CMD_EXT4 1 |
| #define CONFIG_CMD_GPIO 1 |
| #define CONFIG_CMD_RUN 1 |
| #define CONFIG_CMD_REBOOT 1 |
| #define CONFIG_CMD_ECHO 1 |
| #define CONFIG_CMD_JTAG 1 |
| #define CONFIG_CMD_AUTOSCRIPT 1 |
| #define CONFIG_CMD_BMP 1 |
| #define CONFIG_CMD_USB 1 |
| #define CONFIG_CMD_NET 1 |
| #define CONFIG_CMD_MISC 1 |
| #define CONFIG_CMD_ITEST 1 |
| #define CONFIG_CMD_CPU_TEMP 1 |
| #define CONFIG_CMD_MEMTEST 1 |
| //#define CONFIG_CMD_USB_MASS_STORAGE 1 |
| //#define CONFIG_CMD_FASTBOOT 1 |
| //#define CONFIG_CMD_INI 1 |
| |
| #if defined(CONFIG_CMD_USB_MASS_STORAGE) |
| #define CONFIG_USB_GADGET 1 |
| #define CONFIG_USB_GADGET_MASS_STORAGE 1 |
| #define CONFIG_USBDOWNLOAD_GADGET 1 |
| #endif |
| |
| #if defined(CONFIG_USB_GADGET) |
| #define CONFIG_USB_GADGET_DUALSPEED 1 |
| #define CONFIG_USB_GADGET_S3C_UDC_OTG 1 |
| #define CONFIG_USB_GADGET_VBUS_DRAW 0 |
| #define CONFIG_SYS_CACHELINE_SIZE 64 |
| #endif |
| |
| #if defined(CONFIG_USBDOWNLOAD_GADGET) |
| #define CONFIG_G_DNL_VENDOR_NUM 0x18d1 |
| #define CONFIG_G_DNL_PRODUCT_NUM 0x0002 |
| #define CONFIG_G_DNL_MANUFACTURER "Hardkernel Co., Ltd" |
| #endif |
| |
| #if defined(CONFIG_CMD_FASTBOOT) |
| #define CONFIG_USB_FASTBOOT_BUF_ADDR CONFIG_SYS_LOAD_ADDR |
| #define CONFIG_USB_FASTBOOT_BUF_SIZE SZ_512M |
| #define CONFIG_FASTBOOT_FLASH 1 |
| #if defined(CONFIG_FASTBOOT_FLASH) |
| #define CONFIG_FASTBOOT_FLASH_MMC_DEV 0 |
| #endif |
| #endif |
| |
| #if defined(CONFIG_CMD_MEMTEST) |
| #define CONFIG_SYS_MEMTEST_START CONFIG_SYS_LOAD_ADDR |
| #define CONFIG_SYS_MEMTEST_END \ |
| (PHYS_SDRAM_1_SIZE - CONFIG_SYS_MEMTEST_START) |
| #define CONFIG_SYS_ALT_MEMTEST 1 |
| #endif |
| |
| /* File systems */ |
| #define CONFIG_DOS_PARTITION 1 |
| #define CONFIG_MMC 1 |
| #define CONFIG_FS_FAT 1 |
| #define CONFIG_FS_EXT4 1 |
| #define CONFIG_LZO 1 |
| |
| /* storage: emmc/nand/sd */ |
| #define CONFIG_AML_NAND 1 |
| #define CONFIG_ENV_OVERWRITE |
| #define CONFIG_ENV_IS_IN_MMC 1 |
| #define CONFIG_SYS_MMC_ENV_DEV 0 |
| #define CONFIG_AML_SD_EMMC 1 |
| |
| #if defined(CONFIG_AML_SD_EMMC) |
| #define CONFIG_GENERIC_MMC 1 |
| #define CONFIG_CMD_MMC 1 |
| #endif |
| |
| #define CONFIG_PARTITIONS 1 |
| #define CONFIG_SYS_NO_FLASH 1 |
| |
| /* VPU */ |
| #define CONFIG_AML_VPU 1 |
| |
| #if defined(CONFIG_AML_VPU) |
| #define CONFIG_VPU_PRESET 1 |
| #endif |
| |
| /* DISPLAY & HDMITX */ |
| #define CONFIG_AML_HDMITX20 1 |
| #define CONFIG_AML_CANVAS 1 |
| #define CONFIG_AML_VOUT 1 |
| #define CONFIG_AML_OSD 1 |
| #define CONFIG_OSD_SCALE_ENABLE 1 |
| |
| #if defined(CONFIG_AML_VOUT) |
| #define CONFIG_AML_CVBS 1 |
| #endif |
| |
| /* USB |
| * Enable CONFIG_MUSB_HCD for Host functionalities MSC, keyboard |
| * Enable CONFIG_MUSB_UDD for Device functionalities. |
| */ |
| /* #define CONFIG_MUSB_UDC 1 */ |
| |
| #if defined(CONFIG_CMD_USB) |
| #define CONFIG_M8_USBPORT_BASE_A 0xc9000000 |
| #define CONFIG_M8_USBPORT_BASE_B 0xc9100000 |
| #define CONFIG_USB_STORAGE 1 |
| #define CONFIG_USB_DWC_OTG_HCD 1 |
| #define CONFIG_USB_DWC_OTG_294 1 |
| #endif |
| |
| /* NETWORK */ |
| #if defined(CONFIG_CMD_NET) |
| #define CONFIG_AML_ETHERNET 1 |
| #define CONFIG_NET_MULTI 1 |
| #define CONFIG_CMD_PING 1 |
| #define CONFIG_CMD_DHCP 1 |
| #define CONFIG_CMD_RARP 1 |
| #if 0 |
| #define CONFIG_NET_RGMII 1 |
| #define CONFIG_NET_RMII_CLK_EXTERNAL 1 // Use external 50MHz |
| #endif |
| |
| #define IP101PHY 1 |
| #define CONFIG_HOSTNAME odroidc2 |
| #define CONFIG_ETHADDR 00:15:18:01:81:31 /* MAC address */ |
| #define CONFIG_GATEWAYIP 192.168.0.1 /* Gateway */ |
| #define CONFIG_IPADDR 192.168.0.2 /* IP */ |
| #define CONFIG_NETMASK 255.255.255.0 /* Netmask */ |
| #define CONFIG_SERVERIP 192.168.0.10 /* TFTP server */ |
| #endif |
| |
| /* I2C */ |
| #if defined(CONFIG_CMD_I2C) |
| #define CONFIG_SYS_I2C_AML 1 |
| #define CONFIG_SYS_I2C_SPEED 400000 // kHz |
| #endif |
| |
| /* MISC */ |
| #define CONFIG_EFUSE 1 |
| #define CONFIG_NEED_BL301 1 |
| #define CONFIG_SYS_LONGHELP 1 |
| #define CONFIG_SYS_MEM_TOP_HIDE 0x08000000 /* Hide 128MB for |
| kernel reserve */ |
| //#define CONFIG_DISPLAY_LOGO 1 |
| //#ifdef CONFIG_DISPLAY_LOGO |
| //#define CONFIG_VIDEO_BMP_GZIP 1 |
| //#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (3 << 20) /* for decompressed img */ |
| //#endif |
| |
| /* ODROID reboot reasons */ |
| #define ODROID_REBOOT_CMD_UNKNOWN -1 |
| #define ODROID_REBOOT_CMD_COLD 0x0 |
| #define ODROID_REBOOT_CMD_NORMAL 0x1 |
| #define ODROID_REBOOT_CMD_FASTBOOT 0x5 |
| #define ODROID_REBOOT_CMD_RECOVERY 0x6 |
| |
| #define CONFIG_SECURE_STORAGE 1 |
| |
| //board customer ID |
| #define CONFIG_CUSTOMER_ID (0x8343742714390532) |
| |
| #if defined(CONFIG_CUSTOMER_ID) |
| #undef CONFIG_AML_CUSTOMER_ID |
| #define CONFIG_AML_CUSTOMER_ID CONFIG_CUSTOMER_ID |
| #endif |
| |
| #endif |
