blob: 225567bd90112a0996461502cd08e9f3f65e52da [file] [log] [blame] [edit]
/*
* (C) Copyright 2005-2006
* Stefan Roese, DENX Software Engineering, sr@denx.de.
*
* (C) Copyright 2002 Scott McNutt <smcnutt@artesyncp.com>
*
* SPDX-License-Identifier: GPL-2.0+
*/
/************************************************************************
* board/config_p3p440.h - configuration for Prodrive P3P440
***********************************************************************/
#ifndef __CONFIG_H
#define __CONFIG_H
/*-----------------------------------------------------------------------
* High Level Configuration Options
*----------------------------------------------------------------------*/
#define CONFIG_P3P440 1 /* Board is P3P440 */
#define CONFIG_440GP 1 /* Specifc GP support */
#define CONFIG_440 1 /* ... PPC440 family */
#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call board_early_init_f */
#define CONFIG_MISC_INIT_R 1 /* Call misc_init_r */
#define CONFIG_SYS_TEXT_BASE 0xFFFC0000
#define CONFIG_SYS_CLK_FREQ 33333333 /* external freq to pll */
/*-----------------------------------------------------------------------
* Base addresses -- Note these are effective addresses where the
* actual resources get mapped (not physical addresses)
*----------------------------------------------------------------------*/
#define CONFIG_SYS_SDRAM_BASE 0x00000000 /* _must_ be 0 */
#define CONFIG_SYS_FLASH_BASE 0xff800000 /* start of FLASH */
#define CONFIG_SYS_MONITOR_BASE 0xfffc0000 /* start of monitor */
#define CONFIG_SYS_PCI_MEMBASE 0x80000000 /* mapped pci memory */
#define CONFIG_SYS_ISRAM_BASE 0xc0000000 /* internal SRAM */
#define CONFIG_SYS_PCI_BASE 0xd0000000 /* internal PCI regs */
#define CONFIG_SYS_USB_BASE (CONFIG_SYS_PERIPHERAL_BASE + 0x00000000)
/*-----------------------------------------------------------------------
* Initial RAM & stack pointer (placed in internal SRAM)
*----------------------------------------------------------------------*/
#define CONFIG_SYS_INIT_RAM_ADDR CONFIG_SYS_ISRAM_BASE /* Initial RAM address */
#define CONFIG_SYS_INIT_RAM_SIZE 0x2000 /* Size of used area in RAM */
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /* Reserve 256 kB for Mon*/
#define CONFIG_SYS_MALLOC_LEN (128 * 1024) /* Reserve 128 kB for malloc*/
/*-----------------------------------------------------------------------
* DDR SDRAM
*----------------------------------------------------------------------*/
#define CONFIG_SDRAM_BANK0 1 /* init onboard DDR SDRAM bank 0*/
#define CONFIG_SDRAM_ECC /* enable ECC support */
#define CONFIG_SYS_SDRAM_TABLE { \
{(256 << 20), 13, 0x000C4001}, /* 256MB mode 3, 13x10(4)*/ \
{(64 << 20), 12, 0x00082001}} /* 64MB mode 2, 12x9(4) */
/*-----------------------------------------------------------------------
* Serial Port
*----------------------------------------------------------------------*/
#define CONFIG_CONS_INDEX 1 /* Use UART0 */
#define CONFIG_SYS_NS16550
#define CONFIG_SYS_NS16550_SERIAL
#define CONFIG_SYS_NS16550_REG_SIZE 1
#define CONFIG_SYS_NS16550_CLK get_serial_clock()
#undef CONFIG_SYS_EXT_SERIAL_CLOCK
#define CONFIG_BAUDRATE 115200
#define CONFIG_SYS_BAUDRATE_TABLE \
{ 300, 600, 1200, 2400, 4800, 9600, 19200, 38400, \
57600, 115200, 230400, 460800, 921600 }
/*-----------------------------------------------------------------------
* I2C
*----------------------------------------------------------------------*/
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_PPC4XX
#define CONFIG_SYS_I2C_PPC4XX_CH0
#define CONFIG_SYS_I2C_PPC4XX_SPEED_0 100000
#define CONFIG_SYS_I2C_PPC4XX_SLAVE_0 0x7F
#define CONFIG_SYS_I2C_NOPROBES { {0, 0x69} } /* Don't probe these addrs */
/*-----------------------------------------------------------------------
* I2C RTC
*----------------------------------------------------------------------*/
#define CONFIG_RTC_MAX6900 1 /* MAX6900 RTC */
/*-----------------------------------------------------------------------
* I2C EEPROM (PCF8594C) for environment
*----------------------------------------------------------------------*/
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x54 /* EEPROM PCF8594C */
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1 /* Bytes of address */
/* mask of address bits that overflow into the "EEPROM chip address" */
#define CONFIG_SYS_I2C_EEPROM_ADDR_OVERFLOW 0x07
#define CONFIG_SYS_EEPROM_PAGE_WRITE_BITS 3 /* The Philips PCF8594C has */
/* 8 byte page write mode using */
/* last 3 bits of the address */
#define CONFIG_SYS_EEPROM_PAGE_WRITE_DELAY_MS 40 /* and takes up to 40 msec */
/*-----------------------------------------------------------------------
* Default configuration (environment varibles...)
*----------------------------------------------------------------------*/
#define CONFIG_PREBOOT "echo;" \
"echo Type \\\"run flash_nfs\\\" to mount root filesystem over NFS;" \
"echo"
#undef CONFIG_BOOTARGS
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"hostname=p3p440\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs} console=ttyS0,${baudrate}\0"\
"flash_nfs=run nfsargs addip addtty;" \
"bootm ${kernel_addr}\0" \
"flash_self=run ramargs addip addtty;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"net_nfs=tftp 200000 ${bootfile};run nfsargs addip addtty;" \
"bootm\0" \
"rootpath=/opt/eldk/ppc_4xx\0" \
"bootfile=/tftpboot/p3p440/uImage\0" \
"kernel_addr=ff800000\0" \
"ramdisk_addr=ff810000\0" \
"load=tftp 100000 /tftpboot/p3p440/u-boot.bin\0" \
"update=protect off fffc0000 ffffffff;era fffc0000 ffffffff;" \
"cp.b 100000 fffc0000 40000;" \
"setenv filesize;saveenv\0" \
"upd=run load update\0" \
"unlock=yes\0" \
""
#define CONFIG_BOOTCOMMAND "run net_nfs"
#define CONFIG_BOOTDELAY 5 /* autoboot after 5 seconds */
#define CONFIG_BAUDRATE 115200
#define CONFIG_LOADS_ECHO 1 /* echo on for serial download */
#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /* allow baudrate change */
#define CONFIG_PPC4xx_EMAC
#define CONFIG_MII 1 /* MII PHY management */
#define CONFIG_PHY_ADDR 0x1c /* PHY address */
#define CONFIG_HAS_ETH1
#define CONFIG_PHY1_ADDR 0x1d /* EMAC1 PHY address */
#define CONFIG_SYS_RX_ETH_BUFFER 32 /* Number of ethernet rx buffers & descriptors */
#define CONFIG_NETCONSOLE /* include NetConsole support */
/*
* BOOTP options
*/
#define CONFIG_BOOTP_BOOTFILESIZE
#define CONFIG_BOOTP_BOOTPATH
#define CONFIG_BOOTP_GATEWAY
#define CONFIG_BOOTP_HOSTNAME
/*
* Command line configuration.
*/
#include <config_cmd_default.h>
#define CONFIG_CMD_ASKENV
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_DIAG
#define CONFIG_CMD_ELF
#define CONFIG_CMD_I2C
#define CONFIG_CMD_IRQ
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#define CONFIG_CMD_NFS
#define CONFIG_CMD_PCI
#define CONFIG_CMD_PING
#define CONFIG_CMD_REGINFO
#define CONFIG_CMD_EEPROM
#define CONFIG_CMD_SNTP
#undef CONFIG_WATCHDOG /* watchdog disabled */
/*-----------------------------------------------------------------------
* Miscellaneous configurable options
*----------------------------------------------------------------------*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CONFIG_SYS_CBSIZE 256 /* Console I/O Buffer Size */
#endif
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE+sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE /* Boot Argument Buffer Size */
#define CONFIG_SYS_MEMTEST_START 0x0400000 /* memtest works on */
#define CONFIG_SYS_MEMTEST_END 0x0C00000 /* 4 ... 12 MB in DRAM */
#define CONFIG_SYS_LOAD_ADDR 0x100000 /* default load address */
#define CONFIG_SYS_EXTBDINFO 1 /* To use extended board_into (bd_t) */
#define CONFIG_AUTO_COMPLETE 1 /* add autocompletion support */
#define CONFIG_LOOPW 1 /* enable loopw command */
#define CONFIG_ZERO_BOOTDELAY_CHECK /* check for keypress on bootdelay==0 */
#define CONFIG_VERSION_VARIABLE 1 /* include version env variable */
/*-----------------------------------------------------------------------
* PCI stuff
*----------------------------------------------------------------------*/
/* General PCI */
#define CONFIG_PCI /* include pci support */
#define CONFIG_PCI_INDIRECT_BRIDGE 1 /* indirect PCI bridge support */
#define CONFIG_PCI_PNP /* do pci plug-and-play */
#define CONFIG_PCI_SCAN_SHOW /* show pci devices on startup */
#define CONFIG_SYS_PCI_TARGBASE 0x80000000 /* PCIaddr mapped to CONFIG_SYS_PCI_MEMBASE */
/* Board-specific PCI */
#define CONFIG_SYS_PCI_TARGET_INIT /* let board init pci target */
#define CONFIG_DISABLE_PISE_TEST /* disable PISE test (PCIX only)*/
#define CONFIG_SYS_PCI_SUBSYS_VENDORID 0x10e8 /* AMCC */
#define CONFIG_SYS_PCI_SUBSYS_DEVICEID 0xcafe /* Whatever */
/*-----------------------------------------------------------------------
* External Bus Controller (EBC) Setup
*----------------------------------------------------------------------*/
#define CONFIG_SYS_FLASH0 0xFF800000
#define CONFIG_SYS_FLASH1 0xFF000000
#define CONFIG_SYS_FLASH2 0xFE800000
#define CONFIG_SYS_FLASH3 0xFE000000
#define CONFIG_SYS_USB 0xF0000000
/* Memory Bank 0 (Flash Bank 0, NOR-FLASH) initialization */
#define CONFIG_SYS_EBC_PB0AP 0x03050200
#define CONFIG_SYS_EBC_PB0CR (CONFIG_SYS_FLASH0 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */
/* Memory Bank 1 (Flash Bank 1, NOR-FLASH) initialization */
#define CONFIG_SYS_EBC_PB1AP 0x03050200
#define CONFIG_SYS_EBC_PB1CR (CONFIG_SYS_FLASH1 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */
/* Memory Bank 2 (Flash Bank 2, NOR-FLASH) initialization */
#define CONFIG_SYS_EBC_PB2AP 0x03050200
#define CONFIG_SYS_EBC_PB2CR (CONFIG_SYS_FLASH2 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */
/* Memory Bank 3 (Flash Bank 3, NOR-FLASH) initialization */
#define CONFIG_SYS_EBC_PB3AP 0x03050200
#define CONFIG_SYS_EBC_PB3CR (CONFIG_SYS_FLASH3 | 0x7A000) /* BAS=0xFF8,BS=8MB,BU=R/W,BW=16bit */
/* Memory Bank 7 (USB controller) initialization */
#define CONFIG_SYS_EBC_PB7AP 0x02015000
#define CONFIG_SYS_EBC_PB7CR (CONFIG_SYS_USB | 0xFE000) /* BAS=0xF00,BS=128MB,BU=R/W,BW=16bit*/
/*-----------------------------------------------------------------------
* FLASH related
*----------------------------------------------------------------------*/
#define CONFIG_SYS_FLASH_CFI /* The flash is CFI compatible */
#define CONFIG_FLASH_CFI_DRIVER /* Use common CFI driver */
#define CONFIG_SYS_FLASH_BANKS_LIST { CONFIG_SYS_FLASH3, CONFIG_SYS_FLASH2, CONFIG_SYS_FLASH1, CONFIG_SYS_FLASH0 }
#define CONFIG_SYS_MAX_FLASH_BANKS 4 /* max number of memory banks */
#define CONFIG_SYS_MAX_FLASH_SECT 512 /* max number of sectors on one chip */
#define CONFIG_SYS_FLASH_ERASE_TOUT 120000 /* Timeout for Flash Erase (in ms) */
#define CONFIG_SYS_FLASH_WRITE_TOUT 500 /* Timeout for Flash Write (in ms) */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1 /* use buffered writes (20x faster) */
#define CONFIG_SYS_FLASH_PROTECTION 1 /* use hardware flash protection */
#define CONFIG_SYS_FLASH_EMPTY_INFO /* print 'E' for empty sector on flinfo */
#define CONFIG_SYS_FLASH_QUIET_TEST 1 /* don't warn upon unknown flash */
#define CONFIG_ENV_IS_IN_FLASH 1 /* use FLASH for environment vars */
#define CONFIG_ENV_SECT_SIZE 0x20000 /* size of one complete sector */
#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE 0x2000 /* Total Size of Environment Sector */
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_ADDR_REDUND (CONFIG_ENV_ADDR-CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SIZE_REDUND (CONFIG_ENV_SIZE)
/*
* For booting Linux, the board info and command line data
* have to be in the first 8 MB of memory, since this is
* the maximum mapped by the Linux kernel during initialization.
*/
#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /* Initial Memory map for Linux */
#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#endif
#endif /* __CONFIG_H */