blob: d383fe878f547ecc58a206ba7b60e6037ca206ef [file] [log] [blame] [edit]
/*
* Copyright (C) 2009, Ilya Yanok, Emcraft Systems, <yanok@emcraft.com>
*
* Configuration settings for the Dave/DENX QongEVB-LITE board.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#include <asm/arch/imx-regs.h>
/* High Level Configuration Options */
#define CONFIG_MX31 /* This is a mx31 */
#define CONFIG_QONG
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_SYS_TEXT_BASE 0xa0000000
#define CONFIG_CMDLINE_TAG /* enable passing of ATAGs */
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
/*
* Size of malloc() pool
*/
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 1536 * 1024)
/*
* Hardware drivers
*/
#define CONFIG_MXC_UART
#define CONFIG_MXC_UART_BASE UART1_BASE
#define CONFIG_MXC_GPIO
#define CONFIG_HW_WATCHDOG
#define CONFIG_IMX_WATCHDOG
#define CONFIG_MXC_SPI
#define CONFIG_DEFAULT_SPI_BUS 1
#define CONFIG_DEFAULT_SPI_MODE (SPI_MODE_0 | SPI_CS_HIGH)
#define CONFIG_RTC_MC13XXX
#define CONFIG_POWER
#define CONFIG_POWER_SPI
#define CONFIG_POWER_FSL
#define CONFIG_FSL_PMIC_BUS 1
#define CONFIG_FSL_PMIC_CS 0
#define CONFIG_FSL_PMIC_CLK 100000
#define CONFIG_FSL_PMIC_MODE (SPI_MODE_0 | SPI_CS_HIGH)
#define CONFIG_FSL_PMIC_BITLEN 32
/* FPGA */
#define CONFIG_FPGA
#define CONFIG_QONG_FPGA
#define CONFIG_FPGA_BASE (CS1_BASE)
#define CONFIG_FPGA_LATTICE
#define CONFIG_FPGA_COUNT 1
#ifdef CONFIG_QONG_FPGA
/* Ethernet */
#define CONFIG_DNET
#define CONFIG_DNET_BASE (CS1_BASE + QONG_FPGA_PERIPH_SIZE)
/* Framebuffer and LCD */
#define CONFIG_VIDEO
#define CONFIG_CFB_CONSOLE
#define CONFIG_VIDEO_MX3
#define CONFIG_VIDEO_LOGO
#define CONFIG_VIDEO_SW_CURSOR
#define CONFIG_VGA_AS_SINGLE_DEVICE
#define CONFIG_SYS_CONSOLE_IS_IN_ENV
#define CONFIG_SPLASH_SCREEN
#define CONFIG_CMD_BMP
#define CONFIG_BMP_16BPP
#define CONFIG_VIDEO_BMP_GZIP
#define CONFIG_SYS_VIDEO_LOGO_MAX_SIZE (512 << 10)
/* USB */
#define CONFIG_CMD_USB
#ifdef CONFIG_CMD_USB
#define CONFIG_USB_EHCI /* Enable EHCI USB support */
#define CONFIG_USB_EHCI_MXC
#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
#define CONFIG_MXC_USB_PORT 2
#define CONFIG_MXC_USB_PORTSC (MXC_EHCI_MODE_ULPI | MXC_EHCI_UTMI_8BIT)
#define CONFIG_MXC_USB_FLAGS MXC_EHCI_POWER_PINS_ENABLED
#define CONFIG_EHCI_IS_TDI
#define CONFIG_USB_STORAGE
#define CONFIG_DOS_PARTITION
#define CONFIG_SUPPORT_VFAT
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#endif /* CONFIG_CMD_USB */
/*
* Reducing the ARP timeout from default 5 seconds to 200ms we speed up the
* initial TFTP transfer, should the user wish one, significantly.
*/
#define CONFIG_ARP_TIMEOUT 200UL
#endif /* CONFIG_QONG_FPGA */
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
/***********************************************************
* Command definition
***********************************************************/
#include <config_cmd_default.h>
#define CONFIG_CMD_CACHE
#define CONFIG_CMD_DATE
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
#define CONFIG_CMD_NAND
#define CONFIG_CMD_NET
#define CONFIG_CMD_PING
#define CONFIG_CMD_SETEXPR
#define CONFIG_CMD_SPI
#define CONFIG_CMD_UNZIP
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_BOOTDELAY 5
#define CONFIG_LOADADDR 0x80800000 /* loadaddr env var */
#define CONFIG_EXTRA_ENV_SETTINGS \
"netdev=eth0\0" \
"nfsargs=setenv bootargs root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath}\0" \
"ramargs=setenv bootargs root=/dev/ram rw\0" \
"addip=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}" \
":${hostname}:${netdev}:off panic=1\0" \
"addtty=setenv bootargs ${bootargs}" \
" console=ttymxc0,${baudrate}\0" \
"addmtd=setenv bootargs ${bootargs} ${mtdparts}\0" \
"addmisc=setenv bootargs ${bootargs}\0" \
"uboot_addr=A0000000\0" \
"kernel_addr=A00C0000\0" \
"ramdisk_addr=A0300000\0" \
"u-boot=qong/u-boot.bin\0" \
"kernel_addr_r=80800000\0" \
"hostname=qong\0" \
"bootfile=qong/uImage\0" \
"rootpath=/opt/eldk-4.2-arm/armVFP\0" \
"flash_self=run ramargs addip addtty addmtd addmisc;" \
"bootm ${kernel_addr} ${ramdisk_addr}\0" \
"flash_nfs=run nfsargs addip addtty addmtd addmisc;" \
"bootm ${kernel_addr}\0" \
"net_nfs=tftp ${kernel_addr_r} ${bootfile};" \
"run nfsargs addip addtty addmtd addmisc;" \
"bootm\0" \
"bootcmd=run flash_self\0" \
"load=tftp ${loadaddr} ${u-boot}\0" \
"update=protect off " __stringify(CONFIG_SYS_MONITOR_BASE) \
" +${filesize};era " __stringify(CONFIG_SYS_MONITOR_BASE)\
" +${filesize};cp.b ${fileaddr} " \
__stringify(CONFIG_SYS_MONITOR_BASE) " ${filesize}\0" \
"upd=run load update\0" \
"videomode=video=ctfb:x:640,y:480,depth:16,mode:0,pclk:40000," \
"le:120,ri:40,up:35,lo:10,hs:30,vs:3,sync:100663296," \
"vmode:0\0" \
/*
* Miscellaneous configurable options
*/
#define CONFIG_SYS_LONGHELP /* undef to save memory */
#define CONFIG_SYS_CBSIZE 512 /* Console I/O Buffer Size */
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 32 /* max number of command args */
/* Boot Argument Buffer Size */
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
/* memtest works on first 255MB of RAM */
#define CONFIG_SYS_MEMTEST_START PHYS_SDRAM_1
#define CONFIG_SYS_MEMTEST_END (PHYS_SDRAM_1 + 0xff000000)
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_CMDLINE_EDITING
#define CONFIG_SYS_HUSH_PARSER /* Use the HUSH parser */
#define CONFIG_MISC_INIT_R
/*-----------------------------------------------------------------------
* Physical Memory Map
*/
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM_1 CSD0_BASE
#define PHYS_SDRAM_1_SIZE 0x10000000 /* 256 MB */
/*
* NAND driver
*/
#ifndef __ASSEMBLY__
extern void qong_nand_plat_init(void *chip);
extern int qong_nand_rdy(void *chip);
#endif
#define CONFIG_NAND_PLAT
#define CONFIG_SYS_MAX_NAND_DEVICE 1
#define CONFIG_SYS_NAND_BASE CS3_BASE
#define NAND_PLAT_INIT() qong_nand_plat_init(nand)
#define QONG_NAND_CLE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 24))
#define QONG_NAND_ALE(chip) ((unsigned long)(chip)->IO_ADDR_W | (1 << 23))
#define QONG_NAND_WRITE(addr, cmd) \
do { \
__REG8(addr) = cmd; \
} while (0)
#define NAND_PLAT_WRITE_CMD(chip, cmd) QONG_NAND_WRITE(QONG_NAND_CLE(chip), cmd)
#define NAND_PLAT_WRITE_ADR(chip, cmd) QONG_NAND_WRITE(QONG_NAND_ALE(chip), cmd)
#define NAND_PLAT_DEV_READY(chip) (qong_nand_rdy(chip))
/*-----------------------------------------------------------------------
* FLASH and environment organization
*/
#define CONFIG_SYS_FLASH_BASE CS0_BASE
#define CONFIG_SYS_MAX_FLASH_BANKS 1 /* max number of memory banks */
/* max number of sectors on one chip */
#define CONFIG_SYS_MAX_FLASH_SECT 1024
/* Monitor at beginning of flash */
#define CONFIG_SYS_MONITOR_BASE CONFIG_SYS_FLASH_BASE
#define CONFIG_SYS_MONITOR_LEN 0x40000 /* Reserve 256KiB */
#define CONFIG_ENV_IS_IN_FLASH
#define CONFIG_ENV_SECT_SIZE 0x20000
#define CONFIG_ENV_SIZE CONFIG_ENV_SECT_SIZE
#define CONFIG_ENV_ADDR (CONFIG_SYS_FLASH_BASE + 0x80000)
/* Address and size of Redundant Environment Sector */
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)
#define CONFIG_ENV_SIZE_REDUND CONFIG_ENV_SIZE
/*-----------------------------------------------------------------------
* CFI FLASH driver setup
*/
/* Flash memory is CFI compliant */
#define CONFIG_SYS_FLASH_CFI
/* Use drivers/cfi_flash.c */
#define CONFIG_FLASH_CFI_DRIVER
/* Use buffered writes (~10x faster) */
#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE
/* Use hardware sector protection */
#define CONFIG_SYS_FLASH_PROTECTION
/*
* Filesystem
*/
#define CONFIG_CMD_JFFS2
#define CONFIG_CMD_UBI
#define CONFIG_CMD_UBIFS
#define CONFIG_RBTREE
#define CONFIG_MTD_PARTITIONS
#define CONFIG_CMD_MTDPARTS
#define CONFIG_LZO
#define CONFIG_MTD_DEVICE /* needed for mtdparts commands */
#define CONFIG_FLASH_CFI_MTD
#define MTDIDS_DEFAULT "nor0=physmap-flash.0," \
"nand0=gen_nand"
#define MTDPARTS_DEFAULT \
"mtdparts=physmap-flash.0:" \
"512k(U-Boot),128k(env1),128k(env2)," \
"2304k(kernel),13m(ramdisk),-(user);" \
"gen_nand:" \
"128m(nand)"
/* additions for new relocation code, must be added to all boards */
#define CONFIG_SYS_SDRAM_BASE 0x80000000
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR (CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_GBL_DATA_OFFSET)
#define CONFIG_BOARD_EARLY_INIT_F
#endif /* __CONFIG_H */