blob: a099687d4636ac4821da9213fe7c58eff8345827 [file] [log] [blame] [edit]
/*
* Copyright (C) 2013, 2014 Markus Niebel <Markus.Niebel@tq-group.com>
*
* Configuration settings for the TQ Systems TQMa6<Q,S> module.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#ifndef __CONFIG_H
#define __CONFIG_H
#define CONFIG_MX6
/* SPL */
/* #if defined(CONFIG_SPL_BUILD) */
#define CONFIG_SPL_MMC_SUPPORT
#define CONFIG_SPL_SPI_SUPPORT
#define CONFIG_SPL_FAT_SUPPORT
#define CONFIG_SPL_EXT_SUPPORT
/* common IMX6 SPL configuration */
#include "imx6_spl.h"
/* #endif */
#include "mx6_common.h"
#include <asm/arch/imx-regs.h>
#include <asm/imx-common/gpio.h>
#include <linux/sizes.h>
#if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
#define PHYS_SDRAM_SIZE (512u * SZ_1M)
#elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
#define PHYS_SDRAM_SIZE (1024u * SZ_1M)
#endif
#if defined(CONFIG_MBA6)
#if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
#define CONFIG_DEFAULT_FDT_FILE "imx6dl-mba6x.dtb"
#elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6Q)
#define CONFIG_DEFAULT_FDT_FILE "imx6q-mba6x.dtb"
#endif
#endif
#define CONFIG_DISPLAY_CPUINFO
#define CONFIG_DISPLAY_BOARDINFO
#define CONFIG_SYS_GENERIC_BOARD
#define CONFIG_CMDLINE_TAG
#define CONFIG_SETUP_MEMORY_TAGS
#define CONFIG_INITRD_TAG
#define CONFIG_REVISION_TAG
#define CONFIG_BOARD_EARLY_INIT_F
#define CONFIG_BOARD_LATE_INIT
#define CONFIG_MXC_GPIO
#define CONFIG_MXC_UART
/* SPI */
#define CONFIG_CMD_SPI
#define CONFIG_MXC_SPI
/* SPI Flash */
#define CONFIG_SPI_FLASH
#define CONFIG_SPI_FLASH_STMICRO
#define TQMA6_SPI_FLASH_SECTOR_SIZE SZ_64K
#define CONFIG_CMD_SF
#define CONFIG_SF_DEFAULT_BUS 0
#define CONFIG_SF_DEFAULT_CS 0
#define CONFIG_SF_DEFAULT_SPEED 50000000
#define CONFIG_SF_DEFAULT_MODE (SPI_MODE_0)
/* I2C Configs */
#define CONFIG_CMD_I2C
#define CONFIG_SYS_I2C
#define CONFIG_SYS_I2C_MXC
#define CONFIG_I2C_MULTI_BUS
#define CONFIG_SYS_I2C_SPEED 100000
/* I2C SYSMON (LM75) */
#define CONFIG_DTT_LM75
#if defined(CONFIG_MBA6)
#define CONFIG_DTT_SENSORS { 0, 1 }
#else
#define CONFIG_DTT_SENSORS { 0 }
#endif
#define CONFIG_DTT_MAX_TEMP 70
#define CONFIG_DTT_MIN_TEMP -30
#define CONFIG_DTT_HYSTERESIS 3
#define CONFIG_CMD_DTT
/* I2C EEPROM (M24C64) */
#define CONFIG_SYS_I2C_EEPROM_ADDR 0x50
#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 2
#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_BITS 5 /* 32 Bytes */
#define CONFIG_SYS_I2C_EEPROM_PAGE_WRITE_DELAY_MS 20
#define CONFIG_CMD_EEPROM
#define CONFIG_POWER
#define CONFIG_POWER_I2C
#define CONFIG_POWER_PFUZE100
#define CONFIG_POWER_PFUZE100_I2C_ADDR 0x08
#define TQMA6_PFUZE100_I2C_BUS 2
/* MMC Configs */
#define CONFIG_FSL_ESDHC
#define CONFIG_FSL_USDHC
#define CONFIG_SYS_FSL_ESDHC_ADDR 0
#define CONFIG_MMC
#define CONFIG_CMD_MMC
#define CONFIG_GENERIC_MMC
#define CONFIG_BOUNCE_BUFFER
/* USB Configs */
#define CONFIG_CMD_USB
#define CONFIG_USB_EHCI
#define CONFIG_USB_EHCI_MX6
#define CONFIG_USB_STORAGE
#define CONFIG_USB_HOST_ETHER
#define CONFIG_USB_ETHER_SMSC95XX
#define CONFIG_MXC_USB_PORT 1
#define CONFIG_MXC_USB_PORTSC (PORT_PTS_UTMI | PORT_PTS_PTW)
#define CONFIG_MXC_USB_FLAGS 0
/* Fuses */
#define CONFIG_MXC_OCOTP
#define CONFIG_CMD_FUSE
#define CONFIG_CMD_EXT2
#define CONFIG_CMD_FAT
#define CONFIG_DOS_PARTITION
#define CONFIG_CMD_PING
#define CONFIG_CMD_DHCP
#define CONFIG_CMD_MII
#define CONFIG_CMD_NET
#define CONFIG_FEC_MXC
#define IMX_FEC_BASE ENET_BASE_ADDR
#define CONFIG_PHYLIB
#define CONFIG_MII
#if defined(CONFIG_MBA6)
#define CONFIG_FEC_XCV_TYPE RGMII
#define CONFIG_ETHPRIME "FEC"
#define CONFIG_FEC_MXC_PHYADDR 0x03
#define CONFIG_PHY_MICREL
#define CONFIG_PHY_KSZ9031
#else
#error "define PHY to use for your baseboard"
#endif
#define CONFIG_ARP_TIMEOUT 200UL
/* Network config - Allow larger/faster download for TFTP/NFS */
#define CONFIG_IP_DEFRAG
#define CONFIG_TFTP_BLOCKSIZE 4096
#define CONFIG_NFS_READ_SIZE 4096
#if defined(CONFIG_MBA6)
#define CONFIG_MXC_UART_BASE UART2_BASE
#define CONFIG_CONSOLE_DEV "ttymxc1"
#else
#error "define baseboard specific things (uart, number of SD-card slots)"
#endif
/* allow to overwrite serial and ethaddr */
#define CONFIG_ENV_OVERWRITE
#define CONFIG_CONS_INDEX 1
#define CONFIG_BAUDRATE 115200
/* Command definition */
#include <config_cmd_default.h>
#define CONFIG_CMD_BMODE
#define CONFIG_CMD_BOOTZ
#define CONFIG_CMD_ITEST
#define CONFIG_CMD_SETEXPR
#undef CONFIG_CMD_IMLS
#define CONFIG_BOOTDELAY 3
#define CONFIG_LOADADDR 0x12000000
/* place code in last 4 MiB of RAM */
#if defined(CONFIG_MX6DL) || defined(CONFIG_MX6S)
#define CONFIG_SYS_TEXT_BASE 0x2fc00000
#elif defined(CONFIG_MX6Q) || defined(CONFIG_MX6D)
#define CONFIG_SYS_TEXT_BASE 0x4fc00000
#endif
#define CONFIG_ENV_SIZE (SZ_8K)
/* Size of malloc() pool */
#define CONFIG_SYS_MALLOC_LEN (CONFIG_ENV_SIZE + 2 * SZ_1M)
#if defined(CONFIG_TQMA6X_MMC_BOOT)
#define CONFIG_ENV_IS_IN_MMC
#define TQMA6_UBOOT_OFFSET SZ_1K
#define TQMA6_UBOOT_SECTOR_START 0x2
#define TQMA6_UBOOT_SECTOR_COUNT 0x7fe
#define CONFIG_ENV_OFFSET SZ_1M
#define CONFIG_SYS_MMC_ENV_DEV 0
#define TQMA6_FDT_OFFSET (2 * SZ_1M)
#define TQMA6_FDT_SECTOR_START 0x1000
#define TQMA6_FDT_SECTOR_COUNT 0x800
#define TQMA6_KERNEL_SECTOR_START 0x2000
#define TQMA6_KERNEL_SECTOR_COUNT 0x2000
#define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \
"uboot_start="__stringify(TQMA6_UBOOT_SECTOR_START)"\0" \
"uboot_size="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0" \
"fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0" \
"fdt_size="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0" \
"kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0" \
"kernel_size="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0" \
"mmcdev="__stringify(CONFIG_SYS_MMC_ENV_DEV)"\0" \
"loadimage=mmc dev ${mmcdev}; " \
"mmc read ${loadaddr} ${kernel_start} ${kernel_size};\0" \
"loadfdt=mmc dev ${mmcdev}; " \
"mmc read ${fdt_addr} ${fdt_start} ${fdt_size};\0" \
"update_uboot=if tftp ${uboot}; then " \
"if itest ${filesize} > 0; then " \
"mmc dev ${mmcdev}; mmc rescan; " \
"setexpr blkc ${filesize} / 0x200; " \
"setexpr blkc ${blkc} + 1; " \
"if itest ${blkc} <= ${uboot_size}; then " \
"mmc write ${loadaddr} ${uboot_start} " \
"${blkc}; " \
"fi; " \
"fi; fi; " \
"setenv filesize; setenv blkc \0" \
"update_kernel=run kernel_name; " \
"if tftp ${kernel}; then " \
"if itest ${filesize} > 0; then " \
"mmc dev ${mmcdev}; mmc rescan; " \
"setexpr blkc ${filesize} / 0x200; " \
"setexpr blkc ${blkc} + 1; " \
"if itest ${blkc} <= ${kernel_size}; then " \
"mmc write ${loadaddr} " \
"${kernel_start} ${blkc}; " \
"fi; " \
"fi; " \
"fi; " \
"setenv filesize; setenv blkc \0" \
"update_fdt=if tftp ${fdt_file}; then " \
"if itest ${filesize} > 0; then " \
"mmc dev ${mmcdev}; mmc rescan; " \
"setexpr blkc ${filesize} / 0x200; " \
"setexpr blkc ${blkc} + 1; " \
"if itest ${blkc} <= ${fdt_size}; then " \
"mmc write ${loadaddr} ${fdt_start} ${blkc}; " \
"fi; " \
"fi; fi; " \
"setenv filesize; setenv blkc \0" \
#define CONFIG_BOOTCOMMAND \
"run mmcboot; run netboot; run panicboot"
#elif defined(CONFIG_TQMA6X_SPI_BOOT)
#define TQMA6_UBOOT_OFFSET 0x400
#define TQMA6_UBOOT_SECTOR_START 0x0
/* max u-boot size: 512k */
#define TQMA6_UBOOT_SECTOR_SIZE TQMA6_SPI_FLASH_SECTOR_SIZE
#define TQMA6_UBOOT_SECTOR_COUNT 0x8
#define TQMA6_UBOOT_SIZE (TQMA6_UBOOT_SECTOR_SIZE * \
TQMA6_UBOOT_SECTOR_COUNT)
#define CONFIG_ENV_IS_IN_SPI_FLASH
#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
#define CONFIG_ENV_OFFSET (TQMA6_UBOOT_SIZE)
#define CONFIG_ENV_SECT_SIZE TQMA6_SPI_FLASH_SECTOR_SIZE
#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + \
CONFIG_ENV_SECT_SIZE)
#define CONFIG_ENV_SPI_BUS (CONFIG_SF_DEFAULT_BUS)
#define CONFIG_ENV_SPI_CS (CONFIG_SF_DEFAULT_CS)
#define CONFIG_ENV_SPI_MAX_HZ (CONFIG_SF_DEFAULT_SPEED)
#define CONFIG_ENV_SPI_MODE (CONFIG_SF_DEFAULT_MODE)
#define TQMA6_FDT_OFFSET (CONFIG_ENV_OFFSET_REDUND + \
CONFIG_ENV_SECT_SIZE)
#define TQMA6_FDT_SECT_SIZE (TQMA6_SPI_FLASH_SECTOR_SIZE)
#define TQMA6_FDT_SECTOR_START 0x0a /* 8 Sector u-boot, 2 Sector env */
#define TQMA6_FDT_SECTOR_COUNT 0x01
#define TQMA6_KERNEL_SECTOR_START 0x10
#define TQMA6_KERNEL_SECTOR_COUNT 0x60
#define TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \
"mmcblkdev=0\0" \
"uboot_offset="__stringify(TQMA6_UBOOT_OFFSET)"\0" \
"uboot_sectors="__stringify(TQMA6_UBOOT_SECTOR_COUNT)"\0" \
"fdt_start="__stringify(TQMA6_FDT_SECTOR_START)"\0" \
"fdt_sectors="__stringify(TQMA6_FDT_SECTOR_COUNT)"\0" \
"kernel_start="__stringify(TQMA6_KERNEL_SECTOR_START)"\0" \
"kernel_sectors="__stringify(TQMA6_KERNEL_SECTOR_COUNT)"\0" \
"update_uboot=if tftp ${uboot}; then " \
"if itest ${filesize} > 0; then " \
"setexpr blkc ${filesize} + " \
__stringify(TQMA6_UBOOT_OFFSET) "; " \
"setexpr size ${uboot_sectors} * " \
__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
"if itest ${blkc} <= ${size}; then " \
"sf probe; " \
"sf erase 0 ${size}; " \
"sf write ${loadaddr} ${uboot_offset} " \
"${filesize}; " \
"fi; " \
"fi; fi; " \
"setenv filesize 0; setenv blkc; setenv size \0" \
"update_kernel=run kernel_name; if tftp ${kernel}; then " \
"if itest ${filesize} > 0; then " \
"setexpr size ${kernel_sectors} * " \
__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
"setexpr offset ${kernel_start} * " \
__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
"if itest ${filesize} <= ${size}; then " \
"sf probe; " \
"sf erase ${offset} ${size}; " \
"sf write ${loadaddr} ${offset} " \
"${filesize}; " \
"fi; " \
"fi; fi; " \
"setenv filesize 0; setenv size ; setenv offset\0" \
"update_fdt=if tftp ${fdt_file}; then " \
"if itest ${filesize} > 0; then " \
"setexpr size ${fdt_sectors} * " \
__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
"setexpr offset ${fdt_start} * " \
__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
"if itest ${filesize} <= ${size}; then " \
"sf probe; " \
"sf erase ${offset} ${size}; " \
"sf write ${loadaddr} ${offset} " \
"${filesize}; " \
"fi; " \
"fi; fi; " \
"setenv filesize 0; setenv size ; setenv offset\0" \
"loadimage=sf probe; " \
"setexpr size ${kernel_sectors} * " \
__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
"setexpr offset ${kernel_start} * " \
__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
"sf read ${loadaddr} ${offset} ${size}; " \
"setenv size ; setenv offset\0" \
"loadfdt=sf probe; " \
"setexpr size ${fdt_sectors} * " \
__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
"setexpr offset ${fdt_start} * " \
__stringify(TQMA6_SPI_FLASH_SECTOR_SIZE)"; " \
"sf read ${${fdt_addr}} ${offset} ${size}; " \
"setenv size ; setenv offset\0" \
#define CONFIG_BOOTCOMMAND \
"sf probe; run mmcboot; run netboot; run panicboot" \
#else
#error "need to define boot source"
#endif
/* 128 MiB offset as in ARM related docu for linux suggested */
#define TQMA6_FDT_ADDRESS 0x18000000
#define CONFIG_EXTRA_ENV_SETTINGS \
"board=tqma6\0" \
"uimage=uImage\0" \
"zimage=zImage\0" \
"boot_type=bootz\0" \
"kernel_name=if test \"${boot_type}\" != bootz; then " \
"setenv kernel ${uimage}; " \
"else setenv kernel ${zimage}; fi\0" \
"uboot=u-boot.imx\0" \
"fdt_file=" CONFIG_DEFAULT_FDT_FILE "\0" \
"fdt_addr="__stringify(TQMA6_FDT_ADDRESS)"\0" \
"console=" CONFIG_CONSOLE_DEV "\0" \
"fdt_high=0xffffffff\0" \
"initrd_high=0xffffffff\0" \
"addtty=setenv bootargs ${bootargs} console=${console},${baudrate}\0" \
"addfb=setenv bootargs ${bootargs} " \
"imx-fbdev.legacyfb_depth=32 consoleblank=0\0" \
"mmcpart=2\0" \
"mmcblkdev=0\0" \
"mmcargs=run addmmc addtty addfb\0" \
"addmmc=setenv bootargs ${bootargs} " \
"root=/dev/mmcblk${mmcblkdev}p${mmcpart} rw rootwait\0" \
"mmcboot=echo Booting from mmc ...; " \
"setenv bootargs; " \
"run mmcargs; " \
"run loadimage; " \
"if run loadfdt; then " \
"echo boot device tree kernel ...; " \
"${boot_type} ${loadaddr} - ${fdt_addr}; " \
"else " \
"${boot_type}; " \
"fi;\0" \
"setenv bootargs \0" \
"netdev=eth0\0" \
"rootpath=/srv/nfs/tqma6\0" \
"ipmode=static\0" \
"netargs=run addnfs addip addtty addfb\0" \
"addnfs=setenv bootargs ${bootargs} " \
"root=/dev/nfs rw " \
"nfsroot=${serverip}:${rootpath},v3,tcp;\0" \
"addip_static=setenv bootargs ${bootargs} " \
"ip=${ipaddr}:${serverip}:${gatewayip}:${netmask}:" \
"${hostname}:${netdev}:off\0" \
"addip_dynamic=setenv bootargs ${bootargs} ip=dhcp\0" \
"addip=if test \"${ipmode}\" != static; then " \
"run addip_dynamic; else run addip_static; fi\0" \
"set_getcmd=if test \"${ipmode}\" != static; then " \
"setenv getcmd dhcp; setenv autoload yes; " \
"else setenv getcmd tftp; setenv autoload no; fi\0" \
"netboot=echo Booting from net ...; " \
"run kernel_name; " \
"run set_getcmd; " \
"setenv bootargs; " \
"run netargs; " \
"if ${getcmd} ${kernel}; then " \
"if ${getcmd} ${fdt_addr} ${fdt_file}; then " \
"${boot_type} ${loadaddr} - ${fdt_addr}; " \
"fi; " \
"fi; " \
"echo ... failed\0" \
"panicboot=echo No boot device !!! reset\0" \
TQMA6_EXTRA_BOOTDEV_ENV_SETTINGS \
/* Miscellaneous configurable options */
#define CONFIG_SYS_LONGHELP
#define CONFIG_SYS_HUSH_PARSER
#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
#define CONFIG_AUTO_COMPLETE
#define CONFIG_SYS_CBSIZE 512
/* Print Buffer Size */
#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE + \
sizeof(CONFIG_SYS_PROMPT) + 16)
#define CONFIG_SYS_MAXARGS 16
#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
#define CONFIG_SYS_LOAD_ADDR CONFIG_LOADADDR
#define CONFIG_CMDLINE_EDITING
#define CONFIG_STACKSIZE (128u * SZ_1K)
/* Physical Memory Map */
#define CONFIG_NR_DRAM_BANKS 1
#define PHYS_SDRAM MMDC0_ARB_BASE_ADDR
#define CONFIG_SYS_SDRAM_BASE PHYS_SDRAM
#define CONFIG_SYS_INIT_RAM_ADDR IRAM_BASE_ADDR
#define CONFIG_SYS_INIT_RAM_SIZE IRAM_SIZE
#define CONFIG_SYS_INIT_SP_OFFSET \
(CONFIG_SYS_INIT_RAM_SIZE - GENERATED_GBL_DATA_SIZE)
#define CONFIG_SYS_INIT_SP_ADDR \
(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
/* FLASH and environment organization */
#define CONFIG_SYS_NO_FLASH
#define CONFIG_OF_LIBFDT
#define CONFIG_OF_BOARD_SETUP
#define CONFIG_FIT
#define CONFIG_FIT_VERBOSE
#ifndef CONFIG_SYS_DCACHE_OFF
#define CONFIG_CMD_CACHE
#endif
#endif /* __CONFIG_H */