blob: e54a4cacfabe2d3c8736a0c50b158644c01d7fa7 [file] [log] [blame]
/*
* (C) Copyright 2002
* Wolfgang Denk, DENX Software Engineering, wd@denx.de.
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
/*
* UART test
*
* The Serial Management Controllers (SMC) and the Serial Communication
* Controllers (SCC) listed in ctlr_list array below are tested in
* the loopback UART mode.
* The controllers are configured accordingly and several characters
* are transmitted. The configurable test parameters are:
* MIN_PACKET_LENGTH - minimum size of packet to transmit
* MAX_PACKET_LENGTH - maximum size of packet to transmit
* TEST_NUM - number of tests
*/
#include <post.h>
#if CONFIG_POST & CONFIG_SYS_POST_UART
#if defined(CONFIG_8xx)
#include <commproc.h>
#elif defined(CONFIG_MPC8260)
#include <asm/cpm_8260.h>
#else
#error "Apparently a bad configuration, please fix."
#endif
#include <command.h>
#include <serial.h>
DECLARE_GLOBAL_DATA_PTR;
#define CTLR_SMC 0
#define CTLR_SCC 1
/* The list of controllers to test */
#if defined(CONFIG_MPC823)
static int ctlr_list[][2] =
{ {CTLR_SMC, 0}, {CTLR_SMC, 1}, {CTLR_SCC, 1} };
#else
static int ctlr_list[][2] = { };
#endif
static struct {
void (*init) (int index);
void (*halt) (int index);
void (*putc) (int index, const char c);
int (*getc) (int index);
} ctlr_proc[2];
static char *ctlr_name[2] = { "SMC", "SCC" };
static int proff_smc[] = { PROFF_SMC1, PROFF_SMC2 };
static int proff_scc[] =
{ PROFF_SCC1, PROFF_SCC2, PROFF_SCC3, PROFF_SCC4 };
/*
* SMC callbacks
*/
static void smc_init (int smc_index)
{
static int cpm_cr_ch[] = { CPM_CR_CH_SMC1, CPM_CR_CH_SMC2 };
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
volatile smc_t *sp;
volatile smc_uart_t *up;
volatile cbd_t *tbdf, *rbdf;
volatile cpm8xx_t *cp = &(im->im_cpm);
uint dpaddr;
/* initialize pointers to SMC */
sp = (smc_t *) & (cp->cp_smc[smc_index]);
up = (smc_uart_t *) & cp->cp_dparam[proff_smc[smc_index]];
/* Disable transmitter/receiver.
*/
sp->smc_smcmr &= ~(SMCMR_REN | SMCMR_TEN);
/* Enable SDMA.
*/
im->im_siu_conf.sc_sdcr = 1;
/* clear error conditions */
#ifdef CONFIG_SYS_SDSR
im->im_sdma.sdma_sdsr = CONFIG_SYS_SDSR;
#else
im->im_sdma.sdma_sdsr = 0x83;
#endif
/* clear SDMA interrupt mask */
#ifdef CONFIG_SYS_SDMR
im->im_sdma.sdma_sdmr = CONFIG_SYS_SDMR;
#else
im->im_sdma.sdma_sdmr = 0x00;
#endif
/* Set the physical address of the host memory buffers in
* the buffer descriptors.
*/
#ifdef CONFIG_SYS_ALLOC_DPRAM
dpaddr = dpram_alloc_align (sizeof (cbd_t) * 2 + 2, 8);
#else
dpaddr = CPM_POST_BASE;
#endif
/* Allocate space for two buffer descriptors in the DP ram.
* For now, this address seems OK, but it may have to
* change with newer versions of the firmware.
* damm: allocating space after the two buffers for rx/tx data
*/
rbdf = (cbd_t *) & cp->cp_dpmem[dpaddr];
rbdf->cbd_bufaddr = (uint) (rbdf + 2);
rbdf->cbd_sc = 0;
tbdf = rbdf + 1;
tbdf->cbd_bufaddr = ((uint) (rbdf + 2)) + 1;
tbdf->cbd_sc = 0;
/* Set up the uart parameters in the parameter ram.
*/
up->smc_rbase = dpaddr;
up->smc_tbase = dpaddr + sizeof (cbd_t);
up->smc_rfcr = SMC_EB;
up->smc_tfcr = SMC_EB;
/* Set UART mode, 8 bit, no parity, one stop.
* Enable receive and transmit.
* Set local loopback mode.
*/
sp->smc_smcmr = smcr_mk_clen (9) | SMCMR_SM_UART | (ushort) 0x0004;
/* Mask all interrupts and remove anything pending.
*/
sp->smc_smcm = 0;
sp->smc_smce = 0xff;
/* Set up the baud rate generator.
*/
cp->cp_simode = 0x00000000;
cp->cp_brgc1 =
(((gd->cpu_clk / 16 / gd->baudrate) -
1) << 1) | CPM_BRG_EN;
/* Make the first buffer the only buffer.
*/
tbdf->cbd_sc |= BD_SC_WRAP;
rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
/* Single character receive.
*/
up->smc_mrblr = 1;
up->smc_maxidl = 0;
/* Initialize Tx/Rx parameters.
*/
while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
;
cp->cp_cpcr =
mk_cr_cmd (cpm_cr_ch[smc_index], CPM_CR_INIT_TRX) | CPM_CR_FLG;
while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
;
/* Enable transmitter/receiver.
*/
sp->smc_smcmr |= SMCMR_REN | SMCMR_TEN;
}
static void smc_halt(int smc_index)
{
}
static void smc_putc (int smc_index, const char c)
{
volatile cbd_t *tbdf;
volatile char *buf;
volatile smc_uart_t *up;
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
volatile cpm8xx_t *cpmp = &(im->im_cpm);
up = (smc_uart_t *) & cpmp->cp_dparam[proff_smc[smc_index]];
tbdf = (cbd_t *) & cpmp->cp_dpmem[up->smc_tbase];
/* Wait for last character to go.
*/
buf = (char *) tbdf->cbd_bufaddr;
#if 0
__asm__ ("eieio");
while (tbdf->cbd_sc & BD_SC_READY)
__asm__ ("eieio");
#endif
*buf = c;
tbdf->cbd_datlen = 1;
tbdf->cbd_sc |= BD_SC_READY;
__asm__ ("eieio");
#if 1
while (tbdf->cbd_sc & BD_SC_READY)
__asm__ ("eieio");
#endif
}
static int smc_getc (int smc_index)
{
volatile cbd_t *rbdf;
volatile unsigned char *buf;
volatile smc_uart_t *up;
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
volatile cpm8xx_t *cpmp = &(im->im_cpm);
unsigned char c;
int i;
up = (smc_uart_t *) & cpmp->cp_dparam[proff_smc[smc_index]];
rbdf = (cbd_t *) & cpmp->cp_dpmem[up->smc_rbase];
/* Wait for character to show up.
*/
buf = (unsigned char *) rbdf->cbd_bufaddr;
#if 0
while (rbdf->cbd_sc & BD_SC_EMPTY);
#else
for (i = 100; i > 0; i--) {
if (!(rbdf->cbd_sc & BD_SC_EMPTY))
break;
udelay (1000);
}
if (i == 0)
return -1;
#endif
c = *buf;
rbdf->cbd_sc |= BD_SC_EMPTY;
return (c);
}
/*
* SCC callbacks
*/
static void scc_init (int scc_index)
{
static int cpm_cr_ch[] = {
CPM_CR_CH_SCC1,
CPM_CR_CH_SCC2,
CPM_CR_CH_SCC3,
CPM_CR_CH_SCC4,
};
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
volatile scc_t *sp;
volatile scc_uart_t *up;
volatile cbd_t *tbdf, *rbdf;
volatile cpm8xx_t *cp = &(im->im_cpm);
uint dpaddr;
/* initialize pointers to SCC */
sp = (scc_t *) & (cp->cp_scc[scc_index]);
up = (scc_uart_t *) & cp->cp_dparam[proff_scc[scc_index]];
/* Disable transmitter/receiver.
*/
sp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT);
/* Allocate space for two buffer descriptors in the DP ram.
*/
#ifdef CONFIG_SYS_ALLOC_DPRAM
dpaddr = dpram_alloc_align (sizeof (cbd_t) * 2 + 2, 8);
#else
dpaddr = CPM_POST_BASE;
#endif
/* Enable SDMA.
*/
im->im_siu_conf.sc_sdcr = 0x0001;
/* Set the physical address of the host memory buffers in
* the buffer descriptors.
*/
rbdf = (cbd_t *) & cp->cp_dpmem[dpaddr];
rbdf->cbd_bufaddr = (uint) (rbdf + 2);
rbdf->cbd_sc = 0;
tbdf = rbdf + 1;
tbdf->cbd_bufaddr = ((uint) (rbdf + 2)) + 1;
tbdf->cbd_sc = 0;
/* Set up the baud rate generator.
*/
cp->cp_sicr &= ~(0x000000FF << (8 * scc_index));
/* no |= needed, since BRG1 is 000 */
cp->cp_brgc1 =
(((gd->cpu_clk / 16 / gd->baudrate) -
1) << 1) | CPM_BRG_EN;
/* Set up the uart parameters in the parameter ram.
*/
up->scc_genscc.scc_rbase = dpaddr;
up->scc_genscc.scc_tbase = dpaddr + sizeof (cbd_t);
/* Initialize Tx/Rx parameters.
*/
while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
;
cp->cp_cpcr =
mk_cr_cmd (cpm_cr_ch[scc_index], CPM_CR_INIT_TRX) | CPM_CR_FLG;
while (cp->cp_cpcr & CPM_CR_FLG) /* wait if cp is busy */
;
up->scc_genscc.scc_rfcr = SCC_EB | 0x05;
up->scc_genscc.scc_tfcr = SCC_EB | 0x05;
up->scc_genscc.scc_mrblr = 1; /* Single character receive */
up->scc_maxidl = 0; /* disable max idle */
up->scc_brkcr = 1; /* send one break character on stop TX */
up->scc_parec = 0;
up->scc_frmec = 0;
up->scc_nosec = 0;
up->scc_brkec = 0;
up->scc_uaddr1 = 0;
up->scc_uaddr2 = 0;
up->scc_toseq = 0;
up->scc_char1 = 0x8000;
up->scc_char2 = 0x8000;
up->scc_char3 = 0x8000;
up->scc_char4 = 0x8000;
up->scc_char5 = 0x8000;
up->scc_char6 = 0x8000;
up->scc_char7 = 0x8000;
up->scc_char8 = 0x8000;
up->scc_rccm = 0xc0ff;
/* Set low latency / small fifo.
*/
sp->scc_gsmrh = SCC_GSMRH_RFW;
/* Set UART mode
*/
sp->scc_gsmrl &= ~0xF;
sp->scc_gsmrl |= SCC_GSMRL_MODE_UART;
/* Set local loopback mode.
*/
sp->scc_gsmrl &= ~SCC_GSMRL_DIAG_LE;
sp->scc_gsmrl |= SCC_GSMRL_DIAG_LOOP;
/* Set clock divider 16 on Tx and Rx
*/
sp->scc_gsmrl |= (SCC_GSMRL_TDCR_16 | SCC_GSMRL_RDCR_16);
sp->scc_psmr |= SCU_PSMR_CL;
/* Mask all interrupts and remove anything pending.
*/
sp->scc_sccm = 0;
sp->scc_scce = 0xffff;
sp->scc_dsr = 0x7e7e;
sp->scc_psmr = 0x3000;
/* Make the first buffer the only buffer.
*/
tbdf->cbd_sc |= BD_SC_WRAP;
rbdf->cbd_sc |= BD_SC_EMPTY | BD_SC_WRAP;
/* Enable transmitter/receiver.
*/
sp->scc_gsmrl |= (SCC_GSMRL_ENR | SCC_GSMRL_ENT);
}
static void scc_halt(int scc_index)
{
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
volatile cpm8xx_t *cp = &(im->im_cpm);
volatile scc_t *sp = (scc_t *) & (cp->cp_scc[scc_index]);
sp->scc_gsmrl &= ~(SCC_GSMRL_ENR | SCC_GSMRL_ENT | SCC_GSMRL_DIAG_LE);
}
static void scc_putc (int scc_index, const char c)
{
volatile cbd_t *tbdf;
volatile char *buf;
volatile scc_uart_t *up;
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
volatile cpm8xx_t *cpmp = &(im->im_cpm);
up = (scc_uart_t *) & cpmp->cp_dparam[proff_scc[scc_index]];
tbdf = (cbd_t *) & cpmp->cp_dpmem[up->scc_genscc.scc_tbase];
/* Wait for last character to go.
*/
buf = (char *) tbdf->cbd_bufaddr;
#if 0
__asm__ ("eieio");
while (tbdf->cbd_sc & BD_SC_READY)
__asm__ ("eieio");
#endif
*buf = c;
tbdf->cbd_datlen = 1;
tbdf->cbd_sc |= BD_SC_READY;
__asm__ ("eieio");
#if 1
while (tbdf->cbd_sc & BD_SC_READY)
__asm__ ("eieio");
#endif
}
static int scc_getc (int scc_index)
{
volatile cbd_t *rbdf;
volatile unsigned char *buf;
volatile scc_uart_t *up;
volatile immap_t *im = (immap_t *) CONFIG_SYS_IMMR;
volatile cpm8xx_t *cpmp = &(im->im_cpm);
unsigned char c;
int i;
up = (scc_uart_t *) & cpmp->cp_dparam[proff_scc[scc_index]];
rbdf = (cbd_t *) & cpmp->cp_dpmem[up->scc_genscc.scc_rbase];
/* Wait for character to show up.
*/
buf = (unsigned char *) rbdf->cbd_bufaddr;
#if 0
while (rbdf->cbd_sc & BD_SC_EMPTY);
#else
for (i = 100; i > 0; i--) {
if (!(rbdf->cbd_sc & BD_SC_EMPTY))
break;
udelay (1000);
}
if (i == 0)
return -1;
#endif
c = *buf;
rbdf->cbd_sc |= BD_SC_EMPTY;
return (c);
}
/*
* Test routines
*/
static int test_ctlr (int ctlr, int index)
{
int res = -1;
char test_str[] = "*** UART Test String ***\r\n";
int i;
ctlr_proc[ctlr].init (index);
for (i = 0; i < sizeof (test_str) - 1; i++) {
ctlr_proc[ctlr].putc (index, test_str[i]);
if (ctlr_proc[ctlr].getc (index) != test_str[i])
goto Done;
}
res = 0;
Done:
ctlr_proc[ctlr].halt (index);
if (res != 0) {
post_log ("uart %s%d test failed\n",
ctlr_name[ctlr], index + 1);
}
return res;
}
int uart_post_test (int flags)
{
int res = 0;
int i;
ctlr_proc[CTLR_SMC].init = smc_init;
ctlr_proc[CTLR_SMC].halt = smc_halt;
ctlr_proc[CTLR_SMC].putc = smc_putc;
ctlr_proc[CTLR_SMC].getc = smc_getc;
ctlr_proc[CTLR_SCC].init = scc_init;
ctlr_proc[CTLR_SCC].halt = scc_halt;
ctlr_proc[CTLR_SCC].putc = scc_putc;
ctlr_proc[CTLR_SCC].getc = scc_getc;
for (i = 0; i < ARRAY_SIZE(ctlr_list); i++) {
if (test_ctlr (ctlr_list[i][0], ctlr_list[i][1]) != 0) {
res = -1;
}
}
#if !defined(CONFIG_8xx_CONS_NONE)
serial_reinit_all ();
#endif
return res;
}
#endif /* CONFIG_POST & CONFIG_SYS_POST_UART */