blob: 33d38cfc5493ff683e482dce2af41cc1e2e7bf26 [file] [log] [blame] [edit]
/*
* DENX M28 module
*
* Copyright (C) 2011 Marek Vasut <marek.vasut@gmail.com>
* on behalf of DENX Software Engineering GmbH
*
* SPDX-License-Identifier: GPL-2.0+
*/
#include <common.h>
#include <asm/gpio.h>
#include <asm/io.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux-mx28.h>
#include <asm/arch/clock.h>
#include <asm/arch/sys_proto.h>
#include <linux/mii.h>
#include <miiphy.h>
#include <netdev.h>
#include <errno.h>
DECLARE_GLOBAL_DATA_PTR;
/*
* Functions
*/
int board_early_init_f(void)
{
/* IO0 clock at 480MHz */
mxs_set_ioclk(MXC_IOCLK0, 480000);
/* IO1 clock at 480MHz */
mxs_set_ioclk(MXC_IOCLK1, 480000);
/* SSP0 clock at 96MHz */
mxs_set_sspclk(MXC_SSPCLK0, 96000, 0);
/* SSP2 clock at 160MHz */
mxs_set_sspclk(MXC_SSPCLK2, 160000, 0);
#ifdef CONFIG_CMD_USB
mxs_iomux_setup_pad(MX28_PAD_SSP2_SS1__USB1_OVERCURRENT);
mxs_iomux_setup_pad(MX28_PAD_AUART3_TX__GPIO_3_13 |
MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP);
gpio_direction_output(MX28_PAD_AUART3_TX__GPIO_3_13, 0);
mxs_iomux_setup_pad(MX28_PAD_AUART3_RX__GPIO_3_12 |
MXS_PAD_12MA | MXS_PAD_3V3 | MXS_PAD_PULLUP);
gpio_direction_output(MX28_PAD_AUART3_RX__GPIO_3_12, 0);
#endif
return 0;
}
int board_init(void)
{
/* Adress of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM_1 + 0x100;
return 0;
}
int dram_init(void)
{
return mxs_dram_init();
}
#ifdef CONFIG_CMD_MMC
static int m28_mmc_wp(int id)
{
if (id != 0) {
printf("MXS MMC: Invalid card selected (card id = %d)\n", id);
return 1;
}
return gpio_get_value(MX28_PAD_AUART2_CTS__GPIO_3_10);
}
int board_mmc_init(bd_t *bis)
{
/* Configure WP as input. */
gpio_direction_input(MX28_PAD_AUART2_CTS__GPIO_3_10);
/* Turn on the power to the card. */
gpio_direction_output(MX28_PAD_PWM3__GPIO_3_28, 0);
return mxsmmc_initialize(bis, 0, m28_mmc_wp, NULL);
}
#endif
#ifdef CONFIG_CMD_NET
#define MII_OPMODE_STRAP_OVERRIDE 0x16
#define MII_PHY_CTRL1 0x1e
#define MII_PHY_CTRL2 0x1f
int fecmxc_mii_postcall(int phy)
{
#if defined(CONFIG_DENX_M28_V11) || defined(CONFIG_DENX_M28_V10)
/* KZ8031 PHY on old boards. */
const uint32_t freq = 0x0080;
#else
/* KZ8021 PHY on new boards. */
const uint32_t freq = 0x0000;
#endif
miiphy_write("FEC1", phy, MII_BMCR, 0x9000);
miiphy_write("FEC1", phy, MII_OPMODE_STRAP_OVERRIDE, 0x0202);
if (phy == 3)
miiphy_write("FEC1", 3, MII_PHY_CTRL2, 0x8100 | freq);
return 0;
}
int board_eth_init(bd_t *bis)
{
struct mxs_clkctrl_regs *clkctrl_regs =
(struct mxs_clkctrl_regs *)MXS_CLKCTRL_BASE;
struct eth_device *dev;
int ret;
ret = cpu_eth_init(bis);
if (ret)
return ret;
clrsetbits_le32(&clkctrl_regs->hw_clkctrl_enet,
CLKCTRL_ENET_TIME_SEL_MASK | CLKCTRL_ENET_CLK_OUT_EN,
CLKCTRL_ENET_TIME_SEL_RMII_CLK);
#if !defined(CONFIG_DENX_M28_V11) && !defined(CONFIG_DENX_M28_V10)
/* Reset the new PHY */
gpio_direction_output(MX28_PAD_AUART2_RTS__GPIO_3_11, 0);
udelay(10000);
gpio_set_value(MX28_PAD_AUART2_RTS__GPIO_3_11, 1);
udelay(10000);
#endif
ret = fecmxc_initialize_multi(bis, 0, 0, MXS_ENET0_BASE);
if (ret) {
printf("FEC MXS: Unable to init FEC0\n");
return ret;
}
ret = fecmxc_initialize_multi(bis, 1, 3, MXS_ENET1_BASE);
if (ret) {
printf("FEC MXS: Unable to init FEC1\n");
return ret;
}
dev = eth_get_dev_by_name("FEC0");
if (!dev) {
printf("FEC MXS: Unable to get FEC0 device entry\n");
return -EINVAL;
}
ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
if (ret) {
printf("FEC MXS: Unable to register FEC0 mii postcall\n");
return ret;
}
dev = eth_get_dev_by_name("FEC1");
if (!dev) {
printf("FEC MXS: Unable to get FEC1 device entry\n");
return -EINVAL;
}
ret = fecmxc_register_mii_postcall(dev, fecmxc_mii_postcall);
if (ret) {
printf("FEC MXS: Unable to register FEC1 mii postcall\n");
return ret;
}
return ret;
}
#endif