blob: 5214730a0fea09641b19ca73c1e85608ef99c06b [file] [log] [blame] [edit]
// SPDX-License-Identifier: GPL-2.0+
/*
*
* Copyright (C) 2004-2007, 2012 Freescale Semiconductor, Inc.
* TsiChung Liew (Tsi-Chung.Liew@freescale.com)
*/
#include <common.h>
#include <asm/processor.h>
#include <asm/immap.h>
#include <asm/io.h>
DECLARE_GLOBAL_DATA_PTR;
/*
* Low Power Divider specifications
*/
#define CLOCK_LPD_MIN (1 << 0) /* Divider (decoded) */
#define CLOCK_LPD_MAX (1 << 15) /* Divider (decoded) */
#define CLOCK_PLL_FVCO_MAX 540000000
#define CLOCK_PLL_FVCO_MIN 300000000
#define CLOCK_PLL_FSYS_MAX 266666666
#define CLOCK_PLL_FSYS_MIN 100000000
#define MHZ 1000000
void clock_enter_limp(int lpdiv)
{
ccm_t *ccm = (ccm_t *)MMAP_CCM;
int i, j;
/* Check bounds of divider */
if (lpdiv < CLOCK_LPD_MIN)
lpdiv = CLOCK_LPD_MIN;
if (lpdiv > CLOCK_LPD_MAX)
lpdiv = CLOCK_LPD_MAX;
/* Round divider down to nearest power of two */
for (i = 0, j = lpdiv; j != 1; j >>= 1, i++) ;
#ifdef CONFIG_MCF5445x
/* Apply the divider to the system clock */
clrsetbits_be16(&ccm->cdr, 0x0f00, CCM_CDR_LPDIV(i));
#endif
/* Enable Limp Mode */
setbits_be16(&ccm->misccr, CCM_MISCCR_LIMP);
}
/*
* brief Exit Limp mode
* warning The PLL should be set and locked prior to exiting Limp mode
*/
void clock_exit_limp(void)
{
ccm_t *ccm = (ccm_t *)MMAP_CCM;
pll_t *pll = (pll_t *)MMAP_PLL;
/* Exit Limp mode */
clrbits_be16(&ccm->misccr, CCM_MISCCR_LIMP);
/* Wait for the PLL to lock */
while (!(in_be32(&pll->psr) & PLL_PSR_LOCK))
;
}
#ifdef CONFIG_MCF5441x
void setup_5441x_clocks(void)
{
ccm_t *ccm = (ccm_t *)MMAP_CCM;
pll_t *pll = (pll_t *)MMAP_PLL;
int temp, vco = 0, bootmod_ccr, pdr;
bootmod_ccr = (in_be16(&ccm->ccr) & CCM_CCR_BOOTMOD) >> 14;
switch (bootmod_ccr) {
case 0:
out_be32(&pll->pcr, 0x00000013);
out_be32(&pll->pdr, 0x00e70c61);
clock_exit_limp();
break;
case 2:
break;
case 3:
break;
}
/*Change frequency for Modelo SER1 USB host*/
#ifdef CONFIG_LOW_MCFCLK
temp = in_be32(&pll->pcr);
temp &= ~0x3f;
temp |= 5;
out_be32(&pll->pcr, temp);
temp = in_be32(&pll->pdr);
temp &= ~0x001f0000;
temp |= 0x00040000;
out_be32(&pll->pdr, temp);
__asm__("tpf");
#endif
setbits_be16(&ccm->misccr2, 0x02);
vco = ((in_be32(&pll->pcr) & PLL_CR_FBKDIV_BITS) + 1) *
CONFIG_SYS_INPUT_CLKSRC;
gd->arch.vco_clk = vco;
gd->arch.inp_clk = CONFIG_SYS_INPUT_CLKSRC; /* Input clock */
pdr = in_be32(&pll->pdr);
temp = (pdr & PLL_DR_OUTDIV1_BITS) + 1;
gd->cpu_clk = vco / temp; /* cpu clock */
gd->arch.flb_clk = vco / temp; /* FlexBus clock */
gd->arch.flb_clk >>= 1;
if (in_be16(&ccm->misccr2) & 2) /* fsys/4 */
gd->arch.flb_clk >>= 1;
temp = ((pdr & PLL_DR_OUTDIV2_BITS) >> 5) + 1;
gd->bus_clk = vco / temp; /* bus clock */
}
#endif
#ifdef CONFIG_MCF5445x
void setup_5445x_clocks(void)
{
ccm_t *ccm = (ccm_t *)MMAP_CCM;
pll_t *pll = (pll_t *)MMAP_PLL;
int pllmult_nopci[] = { 20, 10, 24, 18, 12, 6, 16, 8 };
int pllmult_pci[] = { 12, 6, 16, 8 };
int vco = 0, temp, fbtemp, pcrvalue;
int *pPllmult = NULL;
u16 fbpll_mask;
#ifdef CONFIG_PCI
int bPci;
#endif
#ifdef CONFIG_M54455EVB
u8 *cpld = (u8 *)(CONFIG_SYS_CS2_BASE + 3);
#endif
u8 bootmode;
/* To determine PCI is present or not */
if (((in_be16(&ccm->ccr) & CCM_CCR_360_FBCONFIG_MASK) == 0x00e0) ||
((in_be16(&ccm->ccr) & CCM_CCR_360_FBCONFIG_MASK) == 0x0060)) {
pPllmult = &pllmult_pci[0];
fbpll_mask = 3; /* 11b */
#ifdef CONFIG_PCI
bPci = 1;
#endif
} else {
pPllmult = &pllmult_nopci[0];
fbpll_mask = 7; /* 111b */
#ifdef CONFIG_PCI
gd->pci_clk = 0;
bPci = 0;
#endif
}
#ifdef CONFIG_M54455EVB
bootmode = (in_8(cpld) & 0x03);
if (bootmode != 3) {
/* Temporary read from CCR- fixed fb issue, must be the same clock
as pci or input clock, causing cpld/fpga read inconsistancy */
fbtemp = pPllmult[ccm->ccr & fbpll_mask];
/* Break down into small pieces, code still in flex bus */
pcrvalue = in_be32(&pll->pcr) & 0xFFFFF0FF;
temp = fbtemp - 1;
pcrvalue |= PLL_PCR_OUTDIV3(temp);
out_be32(&pll->pcr, pcrvalue);
}
#endif
#ifdef CONFIG_M54451EVB
/* No external logic to read the bootmode, hard coded from built */
#ifdef CONFIG_CF_SBF
bootmode = 3;
#else
bootmode = 2;
/* default value is 16 mul, set to 20 mul */
pcrvalue = (in_be32(&pll->pcr) & 0x00FFFFFF) | 0x14000000;
out_be32(&pll->pcr, pcrvalue);
while ((in_be32(&pll->psr) & PLL_PSR_LOCK) != PLL_PSR_LOCK)
;
#endif
#endif
if (bootmode == 0) {
/* RCON mode */
vco = pPllmult[ccm->rcon & fbpll_mask] * CONFIG_SYS_INPUT_CLKSRC;
if ((vco < CLOCK_PLL_FVCO_MIN) || (vco > CLOCK_PLL_FVCO_MAX)) {
/* invaild range, re-set in PCR */
int temp = ((in_be32(&pll->pcr) & PLL_PCR_OUTDIV2_MASK) >> 4) + 1;
int i, j, bus;
j = (in_be32(&pll->pcr) & 0xFF000000) >> 24;
for (i = j; i < 0xFF; i++) {
vco = i * CONFIG_SYS_INPUT_CLKSRC;
if (vco >= CLOCK_PLL_FVCO_MIN) {
bus = vco / temp;
if (bus <= CLOCK_PLL_FSYS_MIN - MHZ)
continue;
else
break;
}
}
pcrvalue = in_be32(&pll->pcr) & 0x00FF00FF;
fbtemp = ((i - 1) << 8) | ((i - 1) << 12);
pcrvalue |= ((i << 24) | fbtemp);
out_be32(&pll->pcr, pcrvalue);
}
gd->arch.vco_clk = vco; /* Vco clock */
} else if (bootmode == 2) {
/* Normal mode */
vco = ((in_be32(&pll->pcr) & 0xFF000000) >> 24) * CONFIG_SYS_INPUT_CLKSRC;
if ((vco < CLOCK_PLL_FVCO_MIN) || (vco > CLOCK_PLL_FVCO_MAX)) {
/* Default value */
pcrvalue = (in_be32(&pll->pcr) & 0x00FFFFFF);
pcrvalue |= pPllmult[in_be16(&ccm->ccr) & fbpll_mask] << 24;
out_be32(&pll->pcr, pcrvalue);
vco = ((in_be32(&pll->pcr) & 0xFF000000) >> 24) * CONFIG_SYS_INPUT_CLKSRC;
}
gd->arch.vco_clk = vco; /* Vco clock */
} else if (bootmode == 3) {
/* serial mode */
vco = ((in_be32(&pll->pcr) & 0xFF000000) >> 24) * CONFIG_SYS_INPUT_CLKSRC;
gd->arch.vco_clk = vco; /* Vco clock */
}
if ((in_be16(&ccm->ccr) & CCM_MISCCR_LIMP) == CCM_MISCCR_LIMP) {
/* Limp mode */
} else {
gd->arch.inp_clk = CONFIG_SYS_INPUT_CLKSRC; /* Input clock */
temp = (in_be32(&pll->pcr) & PLL_PCR_OUTDIV1_MASK) + 1;
gd->cpu_clk = vco / temp; /* cpu clock */
temp = ((in_be32(&pll->pcr) & PLL_PCR_OUTDIV2_MASK) >> 4) + 1;
gd->bus_clk = vco / temp; /* bus clock */
temp = ((in_be32(&pll->pcr) & PLL_PCR_OUTDIV3_MASK) >> 8) + 1;
gd->arch.flb_clk = vco / temp; /* FlexBus clock */
#ifdef CONFIG_PCI
if (bPci) {
temp = ((in_be32(&pll->pcr) & PLL_PCR_OUTDIV4_MASK) >> 12) + 1;
gd->pci_clk = vco / temp; /* PCI clock */
}
#endif
}
#ifdef CONFIG_SYS_I2C_FSL
gd->arch.i2c1_clk = gd->bus_clk;
#endif
}
#endif
/* get_clocks() fills in gd->cpu_clock and gd->bus_clk */
int get_clocks(void)
{
#ifdef CONFIG_MCF5441x
setup_5441x_clocks();
#endif
#ifdef CONFIG_MCF5445x
setup_5445x_clocks();
#endif
#ifdef CONFIG_SYS_FSL_I2C
gd->arch.i2c1_clk = gd->bus_clk;
#endif
return (0);
}