blob: 76f159243f13c6b526b0079e1e237448ba38f0a7 [file] [log] [blame]
# SPDX-License-Identifier: GPL-2.0+
#
# Copyright (C) 2015, Bin Meng <bmeng.cn@gmail.com>
config INTEL_QUARK
bool
select HAVE_RMU
select ARCH_EARLY_INIT_R
select ARCH_MISC_INIT
imply ENABLE_MRC_CACHE
imply ETH_DESIGNWARE
imply ICH_SPI
imply INTEL_ICH6_GPIO
imply MMC
imply MMC_PCI
imply MMC_SDHCI
imply MMC_SDHCI_SDMA
imply SPI_FLASH
imply SYS_NS16550
imply USB
imply USB_EHCI_HCD
if INTEL_QUARK
config HAVE_RMU
bool "Add a Remote Management Unit (RMU) binary"
help
Select this option to add a Remote Management Unit (RMU) binary
to the resulting U-Boot image. It is a data block (up to 64K) of
machine-specific code which must be put in the flash for the RMU
within the Quark SoC processor to access when powered up before
system BIOS is executed.
config RMU_FILE
string "Remote Management Unit (RMU) binary filename"
depends on HAVE_RMU
default "rmu.bin"
help
The filename of the file to use as Remote Management Unit (RMU)
binary in the board directory.
config RMU_ADDR
hex "Remote Management Unit (RMU) binary location"
depends on HAVE_RMU
default 0xfff00000
help
The location of the RMU binary is determined by a strap. It must be
put in flash at a location matching the strap-determined base address.
The default base address of 0xfff00000 indicates that the binary must
be located at offset 0 from the beginning of a 1MB flash device.
config HAVE_CMC
bool
default HAVE_RMU
config CMC_FILE
string
depends on HAVE_CMC
default RMU_FILE
config CMC_ADDR
hex
depends on HAVE_CMC
default RMU_ADDR
config ESRAM_BASE
hex
default 0x80000000
help
Embedded SRAM (eSRAM) memory-mapped base address.
config PCIE_ECAM_BASE
hex
default 0xe0000000
config RCBA_BASE
hex
default 0xfed1c000
help
Root Complex register block memory-mapped base address.
config ACPI_PM1_BASE
hex
default 0x1000
help
ACPI Power Managment 1 (PM1) i/o-mapped base address.
This device is defined in ACPI specification, with 16 bytes in size.
config ACPI_PBLK_BASE
hex
default 0x1010
help
ACPI Processor Block (PBLK) i/o-mapped base address.
This device is defined in ACPI specification, with 16 bytes in size.
config SPI_DMA_BASE
hex
default 0x1020
help
SPI DMA i/o-mapped base address.
config GPIO_BASE
hex
default 0x1080
help
GPIO i/o-mapped base address.
config ACPI_GPE0_BASE
hex
default 0x1100
help
ACPI General Purpose Event 0 (GPE0) i/o-mapped base address.
This device is defined in ACPI specification, with 64 bytes in size.
config WDT_BASE
hex
default 0x1140
help
Watchdog timer i/o-mapped base address.
config SYS_CAR_ADDR
hex
default ESRAM_BASE
config SYS_CAR_SIZE
hex
default 0x8000
help
Space in bytes in eSRAM used as Cache-As-ARM (CAR).
Note this size must not exceed eSRAM's total size.
endif