blob: c88b9fc8c0efff84a9d7d15c2d689940c86cc8d0 [file] [log] [blame] [edit]
// SPDX-License-Identifier: GPL-2.0+
/*
* (C) Copyright 2014
* Heiko Schocher, DENX Software Engineering, hs@denx.de.
*
* Based on:
* Copyright (C) 2012 Freescale Semiconductor, Inc.
*
* Author: Fabio Estevam <fabio.estevam@freescale.com>
*/
#include <asm/arch/clock.h>
#include <asm/arch/imx-regs.h>
#include <asm/arch/iomux.h>
#include <asm/arch/mx6-pins.h>
#include <linux/errno.h>
#include <asm/gpio.h>
#include <asm/mach-imx/iomux-v3.h>
#include <asm/mach-imx/boot_mode.h>
#include <asm/mach-imx/mxc_i2c.h>
#include <asm/mach-imx/video.h>
#include <mmc.h>
#include <fsl_esdhc.h>
#include <miiphy.h>
#include <netdev.h>
#include <asm/arch/mxc_hdmi.h>
#include <asm/arch/crm_regs.h>
#include <linux/fb.h>
#include <ipu_pixfmt.h>
#include <input.h>
#include <asm/io.h>
#include <asm/arch/sys_proto.h>
#include <pwm.h>
DECLARE_GLOBAL_DATA_PTR;
#define UART_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define USDHC_PAD_CTRL (PAD_CTL_PUS_47K_UP | \
PAD_CTL_SPEED_LOW | PAD_CTL_DSE_80ohm | \
PAD_CTL_SRE_FAST | PAD_CTL_HYS)
#define ENET_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS)
#define SPI_PAD_CTRL (PAD_CTL_HYS | PAD_CTL_SPEED_MED | \
PAD_CTL_DSE_40ohm | PAD_CTL_SRE_FAST)
#define I2C_PAD_CTRL (PAD_CTL_PUS_100K_UP | \
PAD_CTL_SPEED_MED | PAD_CTL_DSE_40ohm | PAD_CTL_HYS | \
PAD_CTL_ODE | PAD_CTL_SRE_FAST)
#define PC MUX_PAD_CTRL(I2C_PAD_CTRL)
#define DISP_PAD_CTRL (0x10)
#define ECSPI4_CS1 IMX_GPIO_NR(5, 2)
#if (CONFIG_SYS_BOARD_VERSION == 1)
#include "./aristainetos-v1.c"
#elif ((CONFIG_SYS_BOARD_VERSION == 2) || (CONFIG_SYS_BOARD_VERSION == 3))
#include "./aristainetos-v2.c"
#endif
struct i2c_pads_info i2c_pad_info1 = {
.scl = {
.i2c_mode = MX6_PAD_CSI0_DAT9__I2C1_SCL | PC,
.gpio_mode = MX6_PAD_CSI0_DAT9__GPIO5_IO27 | PC,
.gp = IMX_GPIO_NR(5, 27)
},
.sda = {
.i2c_mode = MX6_PAD_CSI0_DAT8__I2C1_SDA | PC,
.gpio_mode = MX6_PAD_CSI0_DAT8__GPIO5_IO26 | PC,
.gp = IMX_GPIO_NR(5, 26)
}
};
struct i2c_pads_info i2c_pad_info2 = {
.scl = {
.i2c_mode = MX6_PAD_KEY_COL3__I2C2_SCL | PC,
.gpio_mode = MX6_PAD_KEY_COL3__GPIO4_IO12 | PC,
.gp = IMX_GPIO_NR(4, 12)
},
.sda = {
.i2c_mode = MX6_PAD_KEY_ROW3__I2C2_SDA | PC,
.gpio_mode = MX6_PAD_KEY_ROW3__GPIO4_IO13 | PC,
.gp = IMX_GPIO_NR(4, 13)
}
};
iomux_v3_cfg_t const usdhc1_pads[] = {
MX6_PAD_SD1_CLK__SD1_CLK | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_CMD__SD1_CMD | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_DAT0__SD1_DATA0 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_DAT1__SD1_DATA1 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_DAT2__SD1_DATA2 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
MX6_PAD_SD1_DAT3__SD1_DATA3 | MUX_PAD_CTRL(USDHC_PAD_CTRL),
};
int dram_init(void)
{
gd->ram_size = imx_ddr_size();
return 0;
}
#ifdef CONFIG_FSL_ESDHC
struct fsl_esdhc_cfg usdhc_cfg[2] = {
{USDHC1_BASE_ADDR},
{USDHC2_BASE_ADDR},
};
int board_mmc_getcd(struct mmc *mmc)
{
return 1;
}
int board_mmc_init(bd_t *bis)
{
usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC_CLK);
imx_iomux_v3_setup_multiple_pads(usdhc1_pads, ARRAY_SIZE(usdhc1_pads));
#if (CONFIG_SYS_BOARD_VERSION == 2)
/*
* usdhc2 has a levelshifter on the carrier board Rev. DV1,
* that will automatically detect the driving direction.
* During initialisation this isn't working correctly,
* which causes DAT3 to be driven low towards the SD-card.
* This causes a SD-card enetring the SPI-Mode
* and therefore getting inaccessible until next power cycle.
* As workaround we drive the DAT3 line as GPIO and set it high.
* This makes usdhc2 unusable in u-boot, but works for the
* initialisation in Linux
*/
imx_iomux_v3_setup_pad(MX6_PAD_SD2_DAT3__GPIO1_IO12 |
MUX_PAD_CTRL(NO_PAD_CTRL));
gpio_direction_output(IMX_GPIO_NR(1, 12) , 1);
#endif
return fsl_esdhc_initialize(bis, &usdhc_cfg[0]);
}
#endif
/*
* Do not overwrite the console
* Use always serial for U-Boot console
*/
int overwrite_console(void)
{
return 1;
}
struct display_info_t const displays[] = {
{
.bus = -1,
.addr = 0,
.pixfmt = IPU_PIX_FMT_RGB24,
.detect = NULL,
.enable = enable_lvds,
.mode = {
.name = "lb07wv8",
.refresh = 60,
.xres = 800,
.yres = 480,
.pixclock = 30066,
.left_margin = 88,
.right_margin = 88,
.upper_margin = 20,
.lower_margin = 20,
.hsync_len = 80,
.vsync_len = 5,
.sync = FB_SYNC_EXT,
.vmode = FB_VMODE_NONINTERLACED
}
}
#if ((CONFIG_SYS_BOARD_VERSION == 2) || (CONFIG_SYS_BOARD_VERSION == 3))
, {
.bus = -1,
.addr = 0,
.pixfmt = IPU_PIX_FMT_RGB24,
.detect = NULL,
.enable = enable_spi_display,
.mode = {
.name = "lg4573",
.refresh = 57,
.xres = 480,
.yres = 800,
.pixclock = 37037,
.left_margin = 59,
.right_margin = 10,
.upper_margin = 15,
.lower_margin = 15,
.hsync_len = 10,
.vsync_len = 15,
.sync = FB_SYNC_EXT | FB_SYNC_HOR_HIGH_ACT |
FB_SYNC_VERT_HIGH_ACT,
.vmode = FB_VMODE_NONINTERLACED
}
}
#endif
};
size_t display_count = ARRAY_SIZE(displays);
/* no console on this board */
int board_cfb_skip(void)
{
return 1;
}
iomux_v3_cfg_t nfc_pads[] = {
MX6_PAD_NANDF_CLE__NAND_CLE | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_ALE__NAND_ALE | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_WP_B__NAND_WP_B | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_RB0__NAND_READY_B | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_CS0__NAND_CE0_B | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_SD4_CMD__NAND_RE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_SD4_CLK__NAND_WE_B | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D0__NAND_DATA00 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D1__NAND_DATA01 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D2__NAND_DATA02 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D3__NAND_DATA03 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D4__NAND_DATA04 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D5__NAND_DATA05 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D6__NAND_DATA06 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_NANDF_D7__NAND_DATA07 | MUX_PAD_CTRL(NO_PAD_CTRL),
MX6_PAD_SD4_DAT0__NAND_DQS | MUX_PAD_CTRL(NO_PAD_CTRL),
};
static void setup_gpmi_nand(void)
{
struct mxc_ccm_reg *mxc_ccm = (struct mxc_ccm_reg *)CCM_BASE_ADDR;
/* config gpmi nand iomux */
imx_iomux_v3_setup_multiple_pads(nfc_pads,
ARRAY_SIZE(nfc_pads));
/* gate ENFC_CLK_ROOT clock first,before clk source switch */
clrbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
/* config gpmi and bch clock to 100 MHz */
clrsetbits_le32(&mxc_ccm->cs2cdr,
MXC_CCM_CS2CDR_ENFC_CLK_PODF_MASK |
MXC_CCM_CS2CDR_ENFC_CLK_PRED_MASK |
MXC_CCM_CS2CDR_ENFC_CLK_SEL_MASK,
MXC_CCM_CS2CDR_ENFC_CLK_PODF(0) |
MXC_CCM_CS2CDR_ENFC_CLK_PRED(3) |
MXC_CCM_CS2CDR_ENFC_CLK_SEL(3));
/* enable ENFC_CLK_ROOT clock */
setbits_le32(&mxc_ccm->CCGR2, MXC_CCM_CCGR2_IOMUX_IPT_CLK_IO_MASK);
/* enable gpmi and bch clock gating */
setbits_le32(&mxc_ccm->CCGR4,
MXC_CCM_CCGR4_RAWNAND_U_BCH_INPUT_APB_MASK |
MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_BCH_MASK |
MXC_CCM_CCGR4_RAWNAND_U_GPMI_BCH_INPUT_GPMI_IO_MASK |
MXC_CCM_CCGR4_RAWNAND_U_GPMI_INPUT_APB_MASK |
MXC_CCM_CCGR4_PL301_MX6QPER1_BCH_OFFSET);
/* enable apbh clock gating */
setbits_le32(&mxc_ccm->CCGR0, MXC_CCM_CCGR0_APBHDMA_MASK);
}
int board_init(void)
{
struct iomuxc *iomux = (struct iomuxc *)IOMUXC_BASE_ADDR;
/* address of boot parameters */
gd->bd->bi_boot_params = PHYS_SDRAM + 0x100;
setup_spi();
setup_i2c(0, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
&i2c_pad_info1);
setup_i2c(1, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
&i2c_pad_info2);
setup_i2c(2, CONFIG_SYS_I2C_SPEED, CONFIG_SYS_I2C_SLAVE,
&i2c_pad_info3);
setup_i2c4();
/* SPI NOR Flash read only */
gpio_request(CONFIG_GPIO_ENABLE_SPI_FLASH, "ena_spi_nor");
gpio_direction_output(CONFIG_GPIO_ENABLE_SPI_FLASH, 0);
gpio_free(CONFIG_GPIO_ENABLE_SPI_FLASH);
setup_board_gpio();
setup_gpmi_nand();
setup_board_spi();
/* GPIO_1 for USB_OTG_ID */
clrsetbits_le32(&iomux->gpr[1], IOMUXC_GPR1_USB_OTG_ID_SEL_MASK, 0);
imx_iomux_v3_setup_multiple_pads(misc_pads, ARRAY_SIZE(misc_pads));
return 0;
}
int checkboard(void)
{
printf("Board: %s\n", CONFIG_BOARDNAME);
return 0;
}
#ifdef CONFIG_USB_EHCI_MX6
int board_ehci_hcd_init(int port)
{
int ret;
ret = gpio_request(ARISTAINETOS_USB_H1_PWR, "usb-h1-pwr");
if (!ret)
gpio_direction_output(ARISTAINETOS_USB_H1_PWR, 1);
ret = gpio_request(ARISTAINETOS_USB_OTG_PWR, "usb-OTG-pwr");
if (!ret)
gpio_direction_output(ARISTAINETOS_USB_OTG_PWR, 1);
return 0;
}
int board_ehci_power(int port, int on)
{
if (port)
gpio_set_value(ARISTAINETOS_USB_OTG_PWR, on);
else
gpio_set_value(ARISTAINETOS_USB_H1_PWR, on);
return 0;
}
#endif