| // SPDX-License-Identifier: GPL-2.0+ | |
| /* | |
| * Copyright (C) 2013 Freescale Semiconductor, Inc. | |
| * Copyright (C) 2015 ECA Sinters | |
| * | |
| * Author: Fabio Estevam <fabio.estevam@freescale.com> | |
| * Modified by: Boris Brezillon <boris.brezillon@free-electrons.com> | |
| */ | |
| #include <asm/arch/clock.h> | |
| #include <asm/arch/imx-regs.h> | |
| #include <asm/arch/iomux.h> | |
| #include <asm/arch/mx6-pins.h> | |
| #include <linux/errno.h> | |
| #include <asm/gpio.h> | |
| #include <asm/mach-imx/iomux-v3.h> | |
| #include <asm/mach-imx/boot_mode.h> | |
| #include <malloc.h> | |
| #include <mmc.h> | |
| #include <fsl_esdhc.h> | |
| #include <miiphy.h> | |
| #include <netdev.h> | |
| #include <asm/arch/mxc_hdmi.h> | |
| #include <asm/arch/crm_regs.h> | |
| #include <linux/fb.h> | |
| #include <ipu_pixfmt.h> | |
| #include <asm/io.h> | |
| #include <asm/arch/sys_proto.h> | |
| #include <micrel.h> | |
| #include <asm/mach-imx/mxc_i2c.h> | |
| #include <i2c.h> | |
| #include "../common/mx6.h" | |
| DECLARE_GLOBAL_DATA_PTR; | |
| int dram_init(void) | |
| { | |
| gd->ram_size = get_ram_size((void *)PHYS_SDRAM, PHYS_SDRAM_SIZE); | |
| return 0; | |
| } | |
| int board_early_init_f(void) | |
| { | |
| seco_mx6_setup_uart_iomux(); | |
| return 0; | |
| } | |
| int board_phy_config(struct phy_device *phydev) | |
| { | |
| seco_mx6_rgmii_rework(phydev); | |
| if (phydev->drv->config) | |
| phydev->drv->config(phydev); | |
| return 0; | |
| } | |
| int board_eth_init(bd_t *bis) | |
| { | |
| uint32_t base = IMX_FEC_BASE; | |
| struct mii_dev *bus = NULL; | |
| struct phy_device *phydev = NULL; | |
| int ret = 0; | |
| seco_mx6_setup_enet_iomux(); | |
| #ifdef CONFIG_FEC_MXC | |
| bus = fec_get_miibus(base, -1); | |
| if (!bus) | |
| return -ENOMEM; | |
| /* scan phy 4,5,6,7 */ | |
| phydev = phy_find_by_mask(bus, (0xf << 4), PHY_INTERFACE_MODE_RGMII); | |
| if (!phydev) { | |
| free(bus); | |
| return -ENOMEM; | |
| } | |
| printf("using phy at %d\n", phydev->addr); | |
| ret = fec_probe(bis, -1, base, bus, phydev); | |
| if (ret) { | |
| free(phydev); | |
| free(bus); | |
| printf("FEC MXC: %s:failed\n", __func__); | |
| } | |
| #endif | |
| return ret; | |
| } | |
| #define USDHC4_CD_GPIO IMX_GPIO_NR(2, 6) | |
| static struct fsl_esdhc_cfg usdhc_cfg[2] = { | |
| {USDHC3_BASE_ADDR, 0, 4}, | |
| {USDHC4_BASE_ADDR, 0, 4}, | |
| }; | |
| int board_mmc_getcd(struct mmc *mmc) | |
| { | |
| struct fsl_esdhc_cfg *cfg = (struct fsl_esdhc_cfg *)mmc->priv; | |
| int ret = 0; | |
| switch (cfg->esdhc_base) { | |
| case USDHC3_BASE_ADDR: | |
| ret = 1; /* Assume eMMC is always present */ | |
| break; | |
| case USDHC4_BASE_ADDR: | |
| ret = !gpio_get_value(USDHC4_CD_GPIO); | |
| break; | |
| } | |
| return ret; | |
| } | |
| int board_mmc_init(bd_t *bis) | |
| { | |
| u32 index = 0; | |
| int ret; | |
| /* | |
| * Following map is done: | |
| * (U-Boot device node) (Physical Port) | |
| * mmc0 eMMC on Board | |
| * mmc1 Ext SD | |
| */ | |
| for (index = 0; index < CONFIG_SYS_FSL_USDHC_NUM; ++index) { | |
| switch (index) { | |
| case 0: | |
| seco_mx6_setup_usdhc_iomux(3); | |
| usdhc_cfg[0].sdhc_clk = mxc_get_clock(MXC_ESDHC3_CLK); | |
| break; | |
| case 1: | |
| seco_mx6_setup_usdhc_iomux(4); | |
| usdhc_cfg[1].sdhc_clk = mxc_get_clock(MXC_ESDHC4_CLK); | |
| break; | |
| default: | |
| printf("Warning: %d exceed maximum number of SD ports %d\n", | |
| index + 1, CONFIG_SYS_FSL_USDHC_NUM); | |
| return -EINVAL; | |
| } | |
| ret = fsl_esdhc_initialize(bis, &usdhc_cfg[index]); | |
| if (ret) | |
| return ret; | |
| } | |
| return 0; | |
| } | |
| int board_init(void) | |
| { | |
| /* address of boot parameters */ | |
| gd->bd->bi_boot_params = PHYS_SDRAM + 0x100; | |
| imx_iomux_v3_setup_pad(MX6_PAD_NANDF_D4__GPIO2_IO04 | | |
| MUX_PAD_CTRL(NO_PAD_CTRL)); | |
| gpio_direction_output(IMX_GPIO_NR(2, 4), 0); | |
| /* Set Low */ | |
| gpio_set_value(IMX_GPIO_NR(2, 4), 0); | |
| udelay(1000); | |
| /* Set High */ | |
| gpio_set_value(IMX_GPIO_NR(2, 4), 1); | |
| return 0; | |
| } | |
| int checkboard(void) | |
| { | |
| puts("Board: SECO uQ7\n"); | |
| return 0; | |
| } |