| source "drivers/net/phy/Kconfig" | |
| source "drivers/net/pfe_eth/Kconfig" | |
| config DM_ETH | |
| bool "Enable Driver Model for Ethernet drivers" | |
| depends on DM | |
| help | |
| Enable driver model for Ethernet. | |
| The eth_*() interface will be implemented by the UC_ETH class | |
| This is currently implemented in net/eth.c | |
| Look in include/net.h for details. | |
| config DRIVER_TI_CPSW | |
| bool "TI Common Platform Ethernet Switch" | |
| select PHYLIB | |
| help | |
| This driver supports the TI three port switch gigabit ethernet | |
| subsystem found in the TI SoCs. | |
| menuconfig NETDEVICES | |
| bool "Network device support" | |
| depends on NET | |
| default y if DM_ETH | |
| help | |
| You must select Y to enable any network device support | |
| Generally if you have any networking support this is a given | |
| If unsure, say Y | |
| if NETDEVICES | |
| config PHY_GIGE | |
| bool "Enable GbE PHY status parsing and configuration" | |
| help | |
| Enables support for parsing the status output and for | |
| configuring GbE PHYs (affects the inner workings of some | |
| commands and miiphyutil.c). | |
| config AG7XXX | |
| bool "Atheros AG7xxx Ethernet MAC support" | |
| depends on DM_ETH && ARCH_ATH79 | |
| select PHYLIB | |
| help | |
| This driver supports the Atheros AG7xxx Ethernet MAC. This MAC is | |
| present in the Atheros AR7xxx, AR9xxx and QCA9xxx MIPS chips. | |
| config ALTERA_TSE | |
| bool "Altera Triple-Speed Ethernet MAC support" | |
| depends on DM_ETH | |
| select PHYLIB | |
| help | |
| This driver supports the Altera Triple-Speed (TSE) Ethernet MAC. | |
| Please find details on the "Triple-Speed Ethernet MegaCore Function | |
| Resource Center" of Altera. | |
| config BCM_SF2_ETH | |
| bool "Broadcom SF2 (Starfighter2) Ethernet support" | |
| select PHYLIB | |
| help | |
| This is an abstract framework which provides a generic interface | |
| to MAC and DMA management for multiple Broadcom SoCs such as | |
| Cygnus, NSP and bcm28155_ap platforms. | |
| config BCM_SF2_ETH_DEFAULT_PORT | |
| int "Broadcom SF2 (Starfighter2) Ethernet default port number" | |
| depends on BCM_SF2_ETH | |
| default 0 | |
| help | |
| Default port number for the Starfighter2 ethernet driver. | |
| config BCM_SF2_ETH_GMAC | |
| bool "Broadcom SF2 (Starfighter2) GMAC Ethernet support" | |
| depends on BCM_SF2_ETH | |
| help | |
| This flag enables the ethernet support for Broadcom platforms with | |
| GMAC such as Cygnus. This driver is based on the framework provided | |
| by the BCM_SF2_ETH driver. | |
| Say Y to any bcmcygnus based platforms. | |
| config DWC_ETH_QOS | |
| bool "Synopsys DWC Ethernet QOS device support" | |
| depends on DM_ETH | |
| select PHYLIB | |
| help | |
| This driver supports the Synopsys Designware Ethernet QOS (Quality | |
| Of Service) IP block. The IP supports many options for bus type, | |
| clocking/reset structure, and feature list. This driver currently | |
| supports the specific configuration used in NVIDIA's Tegra186 chip, | |
| but should be extensible to other combinations quite easily. | |
| config E1000 | |
| bool "Intel PRO/1000 Gigabit Ethernet support" | |
| help | |
| This driver supports Intel(R) PRO/1000 gigabit ethernet family of | |
| adapters. For more information on how to identify your adapter, go | |
| to the Adapter & Driver ID Guide at: | |
| <http://support.intel.com/support/network/adapter/pro100/21397.htm> | |
| config E1000_SPI_GENERIC | |
| bool "Allow access to the Intel 8257x SPI bus" | |
| depends on E1000 | |
| help | |
| Allow generic access to the SPI bus on the Intel 8257x, for | |
| example with the "sspi" command. | |
| config E1000_SPI | |
| bool "Enable SPI bus utility code" | |
| depends on E1000 | |
| help | |
| Utility code for direct access to the SPI bus on Intel 8257x. | |
| This does not do anything useful unless you set at least one | |
| of CONFIG_CMD_E1000 or CONFIG_E1000_SPI_GENERIC. | |
| config CMD_E1000 | |
| bool "Enable the e1000 command" | |
| depends on E1000 | |
| help | |
| This enables the 'e1000' management command for E1000 devices. When | |
| used on devices with SPI support you can reprogram the EEPROM from | |
| U-Boot. | |
| config ETH_SANDBOX | |
| depends on DM_ETH && SANDBOX | |
| default y | |
| bool "Sandbox: Mocked Ethernet driver" | |
| help | |
| This driver simply responds with fake ARP replies and ping | |
| replies that are used to verify network stack functionality | |
| This driver is particularly useful in the test/dm/eth.c tests | |
| config ETH_SANDBOX_RAW | |
| depends on DM_ETH && SANDBOX | |
| default y | |
| bool "Sandbox: Bridge to Linux Raw Sockets" | |
| help | |
| This driver is a bridge from the bottom of the network stack | |
| in U-Boot to the RAW AF_PACKET API in Linux. This allows real | |
| network traffic to be tested from within sandbox. See | |
| board/sandbox/README.sandbox for more details. | |
| config ETH_DESIGNWARE | |
| bool "Synopsys Designware Ethernet MAC" | |
| select PHYLIB | |
| help | |
| This MAC is present in SoCs from various vendors. It supports | |
| 100Mbit and 1 Gbit operation. You must enable CONFIG_PHYLIB to | |
| provide the PHY (physical media interface). | |
| config ETHOC | |
| bool "OpenCores 10/100 Mbps Ethernet MAC" | |
| help | |
| This MAC is present in OpenRISC and Xtensa XTFPGA boards. | |
| config FEC_MXC_SHARE_MDIO | |
| bool "Share the MDIO bus for FEC controller" | |
| depends on FEC_MXC | |
| config FEC_MXC_MDIO_BASE | |
| hex "MDIO base address for the FEC controller" | |
| depends on FEC_MXC_SHARE_MDIO | |
| help | |
| This specifies the MDIO registers base address. It is used when | |
| two FEC controllers share MDIO bus. | |
| config FEC_MXC | |
| bool "FEC Ethernet controller" | |
| depends on MX5 || MX6 || MX7 | |
| help | |
| This driver supports the 10/100 Fast Ethernet controller for | |
| NXP i.MX processors. | |
| config FTMAC100 | |
| bool "Ftmac100 Ethernet Support" | |
| help | |
| This MAC is present in Andestech SoCs. | |
| config MVNETA | |
| bool "Marvell Armada XP/385/3700 network interface support" | |
| depends on ARMADA_XP || ARMADA_38X || ARMADA_3700 | |
| select PHYLIB | |
| help | |
| This driver supports the network interface units in the | |
| Marvell ARMADA XP, ARMADA 38X and ARMADA 3700 SoCs | |
| config MVPP2 | |
| bool "Marvell Armada 375/7K/8K network interface support" | |
| depends on ARMADA_375 || ARMADA_8K | |
| select PHYLIB | |
| help | |
| This driver supports the network interface units in the | |
| Marvell ARMADA 375, 7K and 8K SoCs. | |
| config MACB | |
| bool "Cadence MACB/GEM Ethernet Interface" | |
| depends on DM_ETH | |
| select PHYLIB | |
| help | |
| The Cadence MACB ethernet interface is found on many Atmel | |
| AT91 and SAMA5 parts. This driver also supports the Cadence | |
| GEM (Gigabit Ethernet MAC) found in some ARM SoC devices. | |
| Say Y to include support for the MACB/GEM chip. | |
| config MACB_ZYNQ | |
| bool "Cadence MACB/GEM Ethernet Interface for Xilinx Zynq" | |
| depends on MACB | |
| help | |
| The Cadence MACB ethernet interface was used on Zynq platform. | |
| Say Y to enable support for the MACB/GEM in Zynq chip. | |
| config PCH_GBE | |
| bool "Intel Platform Controller Hub EG20T GMAC driver" | |
| depends on DM_ETH && DM_PCI | |
| select PHYLIB | |
| help | |
| This MAC is present in Intel Platform Controller Hub EG20T. It | |
| supports 10/100/1000 Mbps operation. | |
| config RGMII | |
| bool "Enable RGMII" | |
| help | |
| Enable the support of the Reduced Gigabit Media-Independent | |
| Interface (RGMII). | |
| config RTL8139 | |
| bool "Realtek 8139 series Ethernet controller driver" | |
| help | |
| This driver supports Realtek 8139 series fast ethernet family of | |
| PCI chipsets/adapters. | |
| config RTL8169 | |
| bool "Realtek 8169 series Ethernet controller driver" | |
| help | |
| This driver supports Realtek 8169 series gigabit ethernet family of | |
| PCI/PCIe chipsets/adapters. | |
| config SMC911X | |
| bool "SMSC LAN911x and LAN921x controller driver" | |
| if SMC911X | |
| config SMC911X_BASE | |
| hex "SMC911X Base Address" | |
| help | |
| Define this to hold the physical address | |
| of the device (I/O space) | |
| choice | |
| prompt "SMC911X bus width" | |
| default SMC911X_16_BIT | |
| config SMC911X_32_BIT | |
| bool "Enable 32-bit interface" | |
| config SMC911X_16_BIT | |
| bool "Enable 16-bit interface" | |
| help | |
| Define this if data bus is 16 bits. If your processor | |
| automatically converts one 32 bit word to two 16 bit | |
| words you may also try CONFIG_SMC911X_32_BIT. | |
| endchoice | |
| endif #SMC911X | |
| config SUN7I_GMAC | |
| bool "Enable Allwinner GMAC Ethernet support" | |
| help | |
| Enable the support for Sun7i GMAC Ethernet controller | |
| config SUN7I_GMAC_FORCE_TXERR | |
| bool "Force PA17 as gmac function" | |
| depends on SUN7I_GMAC | |
| help | |
| Some ethernet phys needs TXERR control. Since the GMAC | |
| doesn't have such signal, setting PA17 as GMAC function | |
| makes the pin output low, which enables data transmission. | |
| config SUN4I_EMAC | |
| bool "Allwinner Sun4i Ethernet MAC support" | |
| depends on DM_ETH | |
| select PHYLIB | |
| help | |
| This driver supports the Allwinner based SUN4I Ethernet MAC. | |
| config SUN8I_EMAC | |
| bool "Allwinner Sun8i Ethernet MAC support" | |
| depends on DM_ETH | |
| select PHYLIB | |
| select PHY_GIGE | |
| help | |
| This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC. | |
| It can be found in H3/A64/A83T based SoCs and compatible with both | |
| External and Internal PHYs. | |
| config SH_ETHER | |
| bool "Renesas SH Ethernet MAC" | |
| select PHYLIB | |
| help | |
| This driver supports the Ethernet for Renesas SH and ARM SoCs. | |
| config XILINX_AXIEMAC | |
| depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP) | |
| select PHYLIB | |
| select MII | |
| bool "Xilinx AXI Ethernet" | |
| help | |
| This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs. | |
| config XILINX_EMACLITE | |
| depends on DM_ETH && (MICROBLAZE || ARCH_ZYNQ || ARCH_ZYNQMP || MIPS) | |
| select PHYLIB | |
| select MII | |
| bool "Xilinx Ethernetlite" | |
| help | |
| This MAC is present in Xilinx Microblaze, Zynq and ZynqMP SoCs. | |
| config ZYNQ_GEM | |
| depends on DM_ETH && (ARCH_ZYNQ || ARCH_ZYNQMP) | |
| select PHYLIB | |
| bool "Xilinx Ethernet GEM" | |
| help | |
| This MAC is present in Xilinx Zynq and ZynqMP SoCs. | |
| config PIC32_ETH | |
| bool "Microchip PIC32 Ethernet Support" | |
| depends on DM_ETH && MACH_PIC32 | |
| select PHYLIB | |
| help | |
| This driver implements 10/100 Mbps Ethernet and MAC layer for | |
| Microchip PIC32 microcontrollers. | |
| config GMAC_ROCKCHIP | |
| bool "Rockchip Synopsys Designware Ethernet MAC" | |
| depends on DM_ETH && ETH_DESIGNWARE | |
| help | |
| This driver provides Rockchip SoCs network support based on the | |
| Synopsys Designware driver. | |
| config RENESAS_RAVB | |
| bool "Renesas Ethernet AVB MAC" | |
| depends on DM_ETH && RCAR_GEN3 | |
| select PHYLIB | |
| help | |
| This driver implements support for the Ethernet AVB block in | |
| Renesas M3 and H3 SoCs. | |
| config MPC8XX_FEC | |
| bool "Fast Ethernet Controller on MPC8XX" | |
| depends on MPC8xx | |
| select MII | |
| help | |
| This driver implements support for the Fast Ethernet Controller | |
| on MPC8XX | |
| config ETHER_ON_FEC1 | |
| bool "FEC1" | |
| depends on MPC8XX_FEC | |
| default y | |
| config FEC1_PHY | |
| int "FEC1 PHY" | |
| depends on ETHER_ON_FEC1 | |
| default -1 | |
| help | |
| Define to the hardcoded PHY address which corresponds | |
| to the given FEC; i. e. | |
| #define CONFIG_FEC1_PHY 4 | |
| means that the PHY with address 4 is connected to FEC1 | |
| When set to -1, means to probe for first available. | |
| config PHY_NORXERR | |
| bool "PHY_NORXERR" | |
| depends on ETHER_ON_FEC1 | |
| default n | |
| help | |
| The PHY does not have a RXERR line (RMII only). | |
| (so program the FEC to ignore it). | |
| config ETHER_ON_FEC2 | |
| bool "FEC2" | |
| depends on MPC8XX_FEC && MPC885 | |
| default y | |
| config FEC2_PHY | |
| int "FEC2 PHY" | |
| depends on ETHER_ON_FEC2 | |
| default -1 | |
| help | |
| Define to the hardcoded PHY address which corresponds | |
| to the given FEC; i. e. | |
| #define CONFIG_FEC1_PHY 4 | |
| means that the PHY with address 4 is connected to FEC1 | |
| When set to -1, means to probe for first available. | |
| config FEC2_PHY_NORXERR | |
| bool "PHY_NORXERR" | |
| depends on ETHER_ON_FEC2 | |
| default n | |
| help | |
| The PHY does not have a RXERR line (RMII only). | |
| (so program the FEC to ignore it). | |
| config SYS_DPAA_QBMAN | |
| bool "Device tree fixup for QBMan on freescale SOCs" | |
| depends on (ARM || PPC) && !SPL_BUILD | |
| default y if ARCH_B4860 || \ | |
| ARCH_B4420 || \ | |
| ARCH_P1023 || \ | |
| ARCH_P2041 || \ | |
| ARCH_T1023 || \ | |
| ARCH_T1024 || \ | |
| ARCH_T1040 || \ | |
| ARCH_T1042 || \ | |
| ARCH_T2080 || \ | |
| ARCH_T2081 || \ | |
| ARCH_T4240 || \ | |
| ARCH_T4160 || \ | |
| ARCH_P4080 || \ | |
| ARCH_P3041 || \ | |
| ARCH_P5040 || \ | |
| ARCH_P5020 || \ | |
| ARCH_LS1043A || \ | |
| ARCH_LS1046A | |
| help | |
| QBman fixups to allow deep sleep in DPAA 1 SOCs | |
| config TSEC_ENET | |
| select PHYLIB | |
| bool "Enable Three-Speed Ethernet Controller" | |
| help | |
| This driver implements support for the (Enhanced) Three-Speed | |
| Ethernet Controller found on Freescale SoCs. | |
| endif # NETDEVICES |