blob: 8d6d86d2b0a1728aaf832b321b9e2352b4d72b5f [file] [log] [blame] [edit]
// SPDX-License-Identifier: GPL-2.0+
/*
* Copyright (c) 2006 Ben Warren, Qstreams Networks Inc.
* With help from the common/soft_spi and arch/powerpc/cpu/mpc8260 drivers
*/
#include <common.h>
#include <malloc.h>
#include <spi.h>
#include <asm/mpc8xxx_spi.h>
#define SPI_EV_NE (0x80000000 >> 22) /* Receiver Not Empty */
#define SPI_EV_NF (0x80000000 >> 23) /* Transmitter Not Full */
#define SPI_MODE_LOOP (0x80000000 >> 1) /* Loopback mode */
#define SPI_MODE_REV (0x80000000 >> 5) /* Reverse mode - MSB first */
#define SPI_MODE_MS (0x80000000 >> 6) /* Always master */
#define SPI_MODE_EN (0x80000000 >> 7) /* Enable interface */
#define SPI_TIMEOUT 1000
struct spi_slave *spi_setup_slave(unsigned int bus, unsigned int cs,
unsigned int max_hz, unsigned int mode)
{
struct spi_slave *slave;
if (!spi_cs_is_valid(bus, cs))
return NULL;
slave = spi_alloc_slave_base(bus, cs);
if (!slave)
return NULL;
/*
* TODO: Some of the code in spi_init() should probably move
* here, or into spi_claim_bus() below.
*/
return slave;
}
void spi_free_slave(struct spi_slave *slave)
{
free(slave);
}
void spi_init(void)
{
volatile spi8xxx_t *spi = &((immap_t *) (CONFIG_SYS_IMMR))->spi;
/*
* SPI pins on the MPC83xx are not muxed, so all we do is initialize
* some registers
*/
spi->mode = SPI_MODE_REV | SPI_MODE_MS | SPI_MODE_EN;
spi->mode = (spi->mode & 0xfff0ffff) | BIT(16); /* Use SYSCLK / 8
(16.67MHz typ.) */
spi->event = 0xffffffff; /* Clear all SPI events */
spi->mask = 0x00000000; /* Mask all SPI interrupts */
spi->com = 0; /* LST bit doesn't do anything, so disregard */
}
int spi_claim_bus(struct spi_slave *slave)
{
return 0;
}
void spi_release_bus(struct spi_slave *slave)
{
}
int spi_xfer(struct spi_slave *slave, unsigned int bitlen, const void *dout,
void *din, unsigned long flags)
{
volatile spi8xxx_t *spi = &((immap_t *) (CONFIG_SYS_IMMR))->spi;
unsigned int tmpdout, tmpdin, event;
int numBlks = DIV_ROUND_UP(bitlen, 32);
int tm, isRead = 0;
unsigned char charSize = 32;
debug("spi_xfer: slave %u:%u dout %08X din %08X bitlen %u\n",
slave->bus, slave->cs, *(uint *) dout, *(uint *) din, bitlen);
if (flags & SPI_XFER_BEGIN)
spi_cs_activate(slave);
spi->event = 0xffffffff; /* Clear all SPI events */
/* handle data in 32-bit chunks */
while (numBlks--) {
tmpdout = 0;
charSize = (bitlen >= 32 ? 32 : bitlen);
/* Shift data so it's msb-justified */
tmpdout = *(u32 *) dout >> (32 - charSize);
/* The LEN field of the SPMODE register is set as follows:
*
* Bit length setting
* len <= 4 3
* 4 < len <= 16 len - 1
* len > 16 0
*/
spi->mode &= ~SPI_MODE_EN;
if (bitlen <= 16) {
if (bitlen <= 4)
spi->mode = (spi->mode & 0xff0fffff) |
(3 << 20);
else
spi->mode = (spi->mode & 0xff0fffff) |
((bitlen - 1) << 20);
} else {
spi->mode = (spi->mode & 0xff0fffff);
/* Set up the next iteration if sending > 32 bits */
bitlen -= 32;
dout += 4;
}
spi->mode |= SPI_MODE_EN;
spi->tx = tmpdout; /* Write the data out */
debug("*** spi_xfer: ... %08x written\n", tmpdout);
/*
* Wait for SPI transmit to get out
* or time out (1 second = 1000 ms)
* The NE event must be read and cleared first
*/
for (tm = 0, isRead = 0; tm < SPI_TIMEOUT; ++tm) {
event = spi->event;
if (event & SPI_EV_NE) {
tmpdin = spi->rx;
spi->event |= SPI_EV_NE;
isRead = 1;
*(u32 *) din = (tmpdin << (32 - charSize));
if (charSize == 32) {
/* Advance output buffer by 32 bits */
din += 4;
}
}
/*
* Only bail when we've had both NE and NF events.
* This will cause timeouts on RO devices, so maybe
* in the future put an arbitrary delay after writing
* the device. Arbitrary delays suck, though...
*/
if (isRead && (event & SPI_EV_NF))
break;
}
if (tm >= SPI_TIMEOUT)
puts("*** spi_xfer: Time out during SPI transfer");
debug("*** spi_xfer: transfer ended. Value=%08x\n", tmpdin);
}
if (flags & SPI_XFER_END)
spi_cs_deactivate(slave);
return 0;
}