blob: e3edd10e29c038a65dc855d9a652b29624e6e48f [file] [log] [blame]
// SPDX-License-Identifier: GPL-2.0+
/*
* drivers/usb/gadget/dwc2_udc_otg.c
* Designware DWC2 on-chip full/high speed USB OTG 2.0 device controllers
*
* Copyright (C) 2008 for Samsung Electronics
*
* BSP Support for Samsung's UDC driver
* available at:
* git://git.kernel.org/pub/scm/linux/kernel/git/kki_ap/linux-2.6-samsung.git
*
* State machine bugfixes:
* Marek Szyprowski <m.szyprowski@samsung.com>
*
* Ported to u-boot:
* Marek Szyprowski <m.szyprowski@samsung.com>
* Lukasz Majewski <l.majewski@samsumg.com>
*/
#undef DEBUG
#include <common.h>
#include <linux/errno.h>
#include <linux/list.h>
#include <malloc.h>
#include <linux/usb/ch9.h>
#include <linux/usb/gadget.h>
#include <asm/byteorder.h>
#include <asm/unaligned.h>
#include <asm/io.h>
#include <asm/mach-types.h>
#include "dwc2_udc_otg_regs.h"
#include "dwc2_udc_otg_priv.h"
#include <usb/lin_gadget_compat.h>
/***********************************************************/
#define OTG_DMA_MODE 1
#define DEBUG_SETUP 0
#define DEBUG_EP0 0
#define DEBUG_ISR 0
#define DEBUG_OUT_EP 0
#define DEBUG_IN_EP 0
#include <usb/dwc2_udc.h>
#define EP0_CON 0
#define EP_MASK 0xF
static char *state_names[] = {
"WAIT_FOR_SETUP",
"DATA_STATE_XMIT",
"DATA_STATE_NEED_ZLP",
"WAIT_FOR_OUT_STATUS",
"DATA_STATE_RECV",
"WAIT_FOR_COMPLETE",
"WAIT_FOR_OUT_COMPLETE",
"WAIT_FOR_IN_COMPLETE",
"WAIT_FOR_NULL_COMPLETE",
};
#define DRIVER_VERSION "15 March 2009"
struct dwc2_udc *the_controller;
static const char driver_name[] = "dwc2-udc";
static const char ep0name[] = "ep0-control";
/* Max packet size*/
static unsigned int ep0_fifo_size = 64;
static unsigned int ep_fifo_size = 512;
static unsigned int ep_fifo_size2 = 1024;
static int reset_available = 1;
static struct usb_ctrlrequest *usb_ctrl;
static dma_addr_t usb_ctrl_dma_addr;
/*
Local declarations.
*/
static int dwc2_ep_enable(struct usb_ep *ep,
const struct usb_endpoint_descriptor *);
static int dwc2_ep_disable(struct usb_ep *ep);
static struct usb_request *dwc2_alloc_request(struct usb_ep *ep,
gfp_t gfp_flags);
static void dwc2_free_request(struct usb_ep *ep, struct usb_request *);
static int dwc2_queue(struct usb_ep *ep, struct usb_request *, gfp_t gfp_flags);
static int dwc2_dequeue(struct usb_ep *ep, struct usb_request *);
static int dwc2_fifo_status(struct usb_ep *ep);
static void dwc2_fifo_flush(struct usb_ep *ep);
static void dwc2_ep0_read(struct dwc2_udc *dev);
static void dwc2_ep0_kick(struct dwc2_udc *dev, struct dwc2_ep *ep);
static void dwc2_handle_ep0(struct dwc2_udc *dev);
static int dwc2_ep0_write(struct dwc2_udc *dev);
static int write_fifo_ep0(struct dwc2_ep *ep, struct dwc2_request *req);
static void done(struct dwc2_ep *ep, struct dwc2_request *req, int status);
static void stop_activity(struct dwc2_udc *dev,
struct usb_gadget_driver *driver);
static int udc_enable(struct dwc2_udc *dev);
static void udc_set_address(struct dwc2_udc *dev, unsigned char address);
static void reconfig_usbd(struct dwc2_udc *dev);
static void set_max_pktsize(struct dwc2_udc *dev, enum usb_device_speed speed);
static void nuke(struct dwc2_ep *ep, int status);
static int dwc2_udc_set_halt(struct usb_ep *_ep, int value);
static void dwc2_udc_set_nak(struct dwc2_ep *ep);
void set_udc_gadget_private_data(void *p)
{
debug_cond(DEBUG_SETUP != 0,
"%s: the_controller: 0x%p, p: 0x%p\n", __func__,
the_controller, p);
the_controller->gadget.dev.device_data = p;
}
void *get_udc_gadget_private_data(struct usb_gadget *gadget)
{
return gadget->dev.device_data;
}
static struct usb_ep_ops dwc2_ep_ops = {
.enable = dwc2_ep_enable,
.disable = dwc2_ep_disable,
.alloc_request = dwc2_alloc_request,
.free_request = dwc2_free_request,
.queue = dwc2_queue,
.dequeue = dwc2_dequeue,
.set_halt = dwc2_udc_set_halt,
.fifo_status = dwc2_fifo_status,
.fifo_flush = dwc2_fifo_flush,
};
#define create_proc_files() do {} while (0)
#define remove_proc_files() do {} while (0)
/***********************************************************/
void __iomem *regs_otg;
struct dwc2_usbotg_reg *reg;
bool dfu_usb_get_reset(void)
{
return !!(readl(&reg->gintsts) & INT_RESET);
}
__weak void otg_phy_init(struct dwc2_udc *dev) {}
__weak void otg_phy_off(struct dwc2_udc *dev) {}
/***********************************************************/
#include "dwc2_udc_otg_xfer_dma.c"
/*
* udc_disable - disable USB device controller
*/
static void udc_disable(struct dwc2_udc *dev)
{
debug_cond(DEBUG_SETUP != 0, "%s: %p\n", __func__, dev);
udc_set_address(dev, 0);
dev->ep0state = WAIT_FOR_SETUP;
dev->gadget.speed = USB_SPEED_UNKNOWN;
dev->usb_address = 0;
otg_phy_off(dev);
}
/*
* udc_reinit - initialize software state
*/
static void udc_reinit(struct dwc2_udc *dev)
{
unsigned int i;
debug_cond(DEBUG_SETUP != 0, "%s: %p\n", __func__, dev);
/* device/ep0 records init */
INIT_LIST_HEAD(&dev->gadget.ep_list);
INIT_LIST_HEAD(&dev->gadget.ep0->ep_list);
dev->ep0state = WAIT_FOR_SETUP;
/* basic endpoint records init */
for (i = 0; i < DWC2_MAX_ENDPOINTS; i++) {
struct dwc2_ep *ep = &dev->ep[i];
if (i != 0)
list_add_tail(&ep->ep.ep_list, &dev->gadget.ep_list);
ep->desc = 0;
ep->stopped = 0;
INIT_LIST_HEAD(&ep->queue);
ep->pio_irqs = 0;
}
/* the rest was statically initialized, and is read-only */
}
#define BYTES2MAXP(x) (x / 8)
#define MAXP2BYTES(x) (x * 8)
/* until it's enabled, this UDC should be completely invisible
* to any USB host.
*/
static int udc_enable(struct dwc2_udc *dev)
{
debug_cond(DEBUG_SETUP != 0, "%s: %p\n", __func__, dev);
otg_phy_init(dev);
reconfig_usbd(dev);
debug_cond(DEBUG_SETUP != 0,
"DWC2 USB 2.0 OTG Controller Core Initialized : 0x%x\n",
readl(&reg->gintmsk));
dev->gadget.speed = USB_SPEED_UNKNOWN;
return 0;
}
/*
Register entry point for the peripheral controller driver.
*/
int usb_gadget_register_driver(struct usb_gadget_driver *driver)
{
struct dwc2_udc *dev = the_controller;
int retval = 0;
unsigned long flags = 0;
debug_cond(DEBUG_SETUP != 0, "%s: %s\n", __func__, "no name");
if (!driver
|| (driver->speed != USB_SPEED_FULL
&& driver->speed != USB_SPEED_HIGH)
|| !driver->bind || !driver->disconnect || !driver->setup)
return -EINVAL;
if (!dev)
return -ENODEV;
if (dev->driver)
return -EBUSY;
spin_lock_irqsave(&dev->lock, flags);
/* first hook up the driver ... */
dev->driver = driver;
spin_unlock_irqrestore(&dev->lock, flags);
if (retval) { /* TODO */
printf("target device_add failed, error %d\n", retval);
return retval;
}
retval = driver->bind(&dev->gadget);
if (retval) {
debug_cond(DEBUG_SETUP != 0,
"%s: bind to driver --> error %d\n",
dev->gadget.name, retval);
dev->driver = 0;
return retval;
}
enable_irq(IRQ_OTG);
debug_cond(DEBUG_SETUP != 0,
"Registered gadget driver %s\n", dev->gadget.name);
udc_enable(dev);
return 0;
}
/*
* Unregister entry point for the peripheral controller driver.
*/
int usb_gadget_unregister_driver(struct usb_gadget_driver *driver)
{
struct dwc2_udc *dev = the_controller;
unsigned long flags = 0;
if (!dev)
return -ENODEV;
if (!driver || driver != dev->driver)
return -EINVAL;
spin_lock_irqsave(&dev->lock, flags);
dev->driver = 0;
stop_activity(dev, driver);
spin_unlock_irqrestore(&dev->lock, flags);
driver->unbind(&dev->gadget);
disable_irq(IRQ_OTG);
udc_disable(dev);
return 0;
}
/*
* done - retire a request; caller blocked irqs
*/
static void done(struct dwc2_ep *ep, struct dwc2_request *req, int status)
{
unsigned int stopped = ep->stopped;
debug("%s: %s %p, req = %p, stopped = %d\n",
__func__, ep->ep.name, ep, &req->req, stopped);
list_del_init(&req->queue);
if (likely(req->req.status == -EINPROGRESS))
req->req.status = status;
else
status = req->req.status;
if (status && status != -ESHUTDOWN) {
debug("complete %s req %p stat %d len %u/%u\n",
ep->ep.name, &req->req, status,
req->req.actual, req->req.length);
}
/* don't modify queue heads during completion callback */
ep->stopped = 1;
#ifdef DEBUG
printf("calling complete callback\n");
{
int i, len = req->req.length;
printf("pkt[%d] = ", req->req.length);
if (len > 64)
len = 64;
for (i = 0; i < len; i++) {
printf("%02x", ((u8 *)req->req.buf)[i]);
if ((i & 7) == 7)
printf(" ");
}
printf("\n");
}
#endif
spin_unlock(&ep->dev->lock);
req->req.complete(&ep->ep, &req->req);
spin_lock(&ep->dev->lock);
debug("callback completed\n");
ep->stopped = stopped;
}
/*
* nuke - dequeue ALL requests
*/
static void nuke(struct dwc2_ep *ep, int status)
{
struct dwc2_request *req;
debug("%s: %s %p\n", __func__, ep->ep.name, ep);
/* called with irqs blocked */
while (!list_empty(&ep->queue)) {
req = list_entry(ep->queue.next, struct dwc2_request, queue);
done(ep, req, status);
}
}
static void stop_activity(struct dwc2_udc *dev,
struct usb_gadget_driver *driver)
{
int i;
/* don't disconnect drivers more than once */
if (dev->gadget.speed == USB_SPEED_UNKNOWN)
driver = 0;
dev->gadget.speed = USB_SPEED_UNKNOWN;
/* prevent new request submissions, kill any outstanding requests */
for (i = 0; i < DWC2_MAX_ENDPOINTS; i++) {
struct dwc2_ep *ep = &dev->ep[i];
ep->stopped = 1;
nuke(ep, -ESHUTDOWN);
}
/* report disconnect; the driver is already quiesced */
if (driver) {
spin_unlock(&dev->lock);
driver->disconnect(&dev->gadget);
spin_lock(&dev->lock);
}
/* re-init driver-visible data structures */
udc_reinit(dev);
}
static void reconfig_usbd(struct dwc2_udc *dev)
{
/* 2. Soft-reset OTG Core and then unreset again. */
int i;
unsigned int uTemp = writel(CORE_SOFT_RESET, &reg->grstctl);
uint32_t dflt_gusbcfg;
uint32_t rx_fifo_sz, tx_fifo_sz, np_tx_fifo_sz;
debug("Reseting OTG controller\n");
dflt_gusbcfg =
0<<15 /* PHY Low Power Clock sel*/
|1<<14 /* Non-Periodic TxFIFO Rewind Enable*/
|0x5<<10 /* Turnaround time*/
|0<<9 | 0<<8 /* [0:HNP disable,1:HNP enable][ 0:SRP disable*/
/* 1:SRP enable] H1= 1,1*/
|0<<7 /* Ulpi DDR sel*/
|0<<6 /* 0: high speed utmi+, 1: full speed serial*/
|0<<4 /* 0: utmi+, 1:ulpi*/
#ifdef CONFIG_USB_GADGET_DWC2_OTG_PHY_BUS_WIDTH_8
|0<<3 /* phy i/f 0:8bit, 1:16bit*/
#else
|1<<3 /* phy i/f 0:8bit, 1:16bit*/
#endif
|0x7<<0; /* HS/FS Timeout**/
if (dev->pdata->usb_gusbcfg)
dflt_gusbcfg = dev->pdata->usb_gusbcfg;
writel(dflt_gusbcfg, &reg->gusbcfg);
/* 3. Put the OTG device core in the disconnected state.*/
uTemp = readl(&reg->dctl);
uTemp |= SOFT_DISCONNECT;
writel(uTemp, &reg->dctl);
udelay(20);
/* 4. Make the OTG device core exit from the disconnected state.*/
uTemp = readl(&reg->dctl);
uTemp = uTemp & ~SOFT_DISCONNECT;
writel(uTemp, &reg->dctl);
/* 5. Configure OTG Core to initial settings of device mode.*/
/* [][1: full speed(30Mhz) 0:high speed]*/
writel(EP_MISS_CNT(1) | DEV_SPEED_HIGH_SPEED_20, &reg->dcfg);
mdelay(1);
/* 6. Unmask the core interrupts*/
writel(GINTMSK_INIT, &reg->gintmsk);
/* 7. Set NAK bit of EP0, EP1, EP2*/
writel(DEPCTL_EPDIS|DEPCTL_SNAK, &reg->out_endp[EP0_CON].doepctl);
writel(DEPCTL_EPDIS|DEPCTL_SNAK, &reg->in_endp[EP0_CON].diepctl);
for (i = 1; i < DWC2_MAX_ENDPOINTS; i++) {
writel(DEPCTL_EPDIS|DEPCTL_SNAK, &reg->out_endp[i].doepctl);
writel(DEPCTL_EPDIS|DEPCTL_SNAK, &reg->in_endp[i].diepctl);
}
/* 8. Unmask EPO interrupts*/
writel(((1 << EP0_CON) << DAINT_OUT_BIT)
| (1 << EP0_CON), &reg->daintmsk);
/* 9. Unmask device OUT EP common interrupts*/
writel(DOEPMSK_INIT, &reg->doepmsk);
/* 10. Unmask device IN EP common interrupts*/
writel(DIEPMSK_INIT, &reg->diepmsk);
rx_fifo_sz = RX_FIFO_SIZE;
np_tx_fifo_sz = NPTX_FIFO_SIZE;
tx_fifo_sz = PTX_FIFO_SIZE;
if (dev->pdata->rx_fifo_sz)
rx_fifo_sz = dev->pdata->rx_fifo_sz;
if (dev->pdata->np_tx_fifo_sz)
np_tx_fifo_sz = dev->pdata->np_tx_fifo_sz;
if (dev->pdata->tx_fifo_sz)
tx_fifo_sz = dev->pdata->tx_fifo_sz;
/* 11. Set Rx FIFO Size (in 32-bit words) */
writel(rx_fifo_sz, &reg->grxfsiz);
/* 12. Set Non Periodic Tx FIFO Size */
writel((np_tx_fifo_sz << 16) | rx_fifo_sz,
&reg->gnptxfsiz);
for (i = 1; i < DWC2_MAX_HW_ENDPOINTS; i++)
writel((rx_fifo_sz + np_tx_fifo_sz + tx_fifo_sz*(i-1)) |
tx_fifo_sz << 16, &reg->dieptxf[i-1]);
/* Flush the RX FIFO */
writel(RX_FIFO_FLUSH, &reg->grstctl);
while (readl(&reg->grstctl) & RX_FIFO_FLUSH)
debug("%s: waiting for DWC2_UDC_OTG_GRSTCTL\n", __func__);
/* Flush all the Tx FIFO's */
writel(TX_FIFO_FLUSH_ALL, &reg->grstctl);
writel(TX_FIFO_FLUSH_ALL | TX_FIFO_FLUSH, &reg->grstctl);
while (readl(&reg->grstctl) & TX_FIFO_FLUSH)
debug("%s: waiting for DWC2_UDC_OTG_GRSTCTL\n", __func__);
/* 13. Clear NAK bit of EP0, EP1, EP2*/
/* For Slave mode*/
/* EP0: Control OUT */
writel(DEPCTL_EPDIS | DEPCTL_CNAK,
&reg->out_endp[EP0_CON].doepctl);
/* 14. Initialize OTG Link Core.*/
writel(GAHBCFG_INIT, &reg->gahbcfg);
}
static void set_max_pktsize(struct dwc2_udc *dev, enum usb_device_speed speed)
{
unsigned int ep_ctrl;
int i;
if (speed == USB_SPEED_HIGH) {
ep0_fifo_size = 64;
ep_fifo_size = 512;
ep_fifo_size2 = 1024;
dev->gadget.speed = USB_SPEED_HIGH;
} else {
ep0_fifo_size = 64;
ep_fifo_size = 64;
ep_fifo_size2 = 64;
dev->gadget.speed = USB_SPEED_FULL;
}
dev->ep[0].ep.maxpacket = ep0_fifo_size;
for (i = 1; i < DWC2_MAX_ENDPOINTS; i++)
dev->ep[i].ep.maxpacket = ep_fifo_size;
/* EP0 - Control IN (64 bytes)*/
ep_ctrl = readl(&reg->in_endp[EP0_CON].diepctl);
writel(ep_ctrl|(0<<0), &reg->in_endp[EP0_CON].diepctl);
/* EP0 - Control OUT (64 bytes)*/
ep_ctrl = readl(&reg->out_endp[EP0_CON].doepctl);
writel(ep_ctrl|(0<<0), &reg->out_endp[EP0_CON].doepctl);
}
static int dwc2_ep_enable(struct usb_ep *_ep,
const struct usb_endpoint_descriptor *desc)
{
struct dwc2_ep *ep;
struct dwc2_udc *dev;
unsigned long flags = 0;
debug("%s: %p\n", __func__, _ep);
ep = container_of(_ep, struct dwc2_ep, ep);
if (!_ep || !desc || ep->desc || _ep->name == ep0name
|| desc->bDescriptorType != USB_DT_ENDPOINT
|| ep->bEndpointAddress != desc->bEndpointAddress
|| ep_maxpacket(ep) <
le16_to_cpu(get_unaligned(&desc->wMaxPacketSize))) {
debug("%s: bad ep or descriptor\n", __func__);
return -EINVAL;
}
/* xfer types must match, except that interrupt ~= bulk */
if (ep->bmAttributes != desc->bmAttributes
&& ep->bmAttributes != USB_ENDPOINT_XFER_BULK
&& desc->bmAttributes != USB_ENDPOINT_XFER_INT) {
debug("%s: %s type mismatch\n", __func__, _ep->name);
return -EINVAL;
}
/* hardware _could_ do smaller, but driver doesn't */
if ((desc->bmAttributes == USB_ENDPOINT_XFER_BULK &&
le16_to_cpu(get_unaligned(&desc->wMaxPacketSize)) >
ep_maxpacket(ep)) || !get_unaligned(&desc->wMaxPacketSize)) {
debug("%s: bad %s maxpacket\n", __func__, _ep->name);
return -ERANGE;
}
dev = ep->dev;
if (!dev->driver || dev->gadget.speed == USB_SPEED_UNKNOWN) {
debug("%s: bogus device state\n", __func__);
return -ESHUTDOWN;
}
ep->stopped = 0;
ep->desc = desc;
ep->pio_irqs = 0;
ep->ep.maxpacket = le16_to_cpu(get_unaligned(&desc->wMaxPacketSize));
/* Reset halt state */
dwc2_udc_set_nak(ep);
dwc2_udc_set_halt(_ep, 0);
spin_lock_irqsave(&ep->dev->lock, flags);
dwc2_udc_ep_activate(ep);
spin_unlock_irqrestore(&ep->dev->lock, flags);
debug("%s: enabled %s, stopped = %d, maxpacket = %d\n",
__func__, _ep->name, ep->stopped, ep->ep.maxpacket);
return 0;
}
/*
* Disable EP
*/
static int dwc2_ep_disable(struct usb_ep *_ep)
{
struct dwc2_ep *ep;
unsigned long flags = 0;
debug("%s: %p\n", __func__, _ep);
ep = container_of(_ep, struct dwc2_ep, ep);
if (!_ep || !ep->desc) {
debug("%s: %s not enabled\n", __func__,
_ep ? ep->ep.name : NULL);
return -EINVAL;
}
spin_lock_irqsave(&ep->dev->lock, flags);
/* Nuke all pending requests */
nuke(ep, -ESHUTDOWN);
ep->desc = 0;
ep->stopped = 1;
spin_unlock_irqrestore(&ep->dev->lock, flags);
debug("%s: disabled %s\n", __func__, _ep->name);
return 0;
}
static struct usb_request *dwc2_alloc_request(struct usb_ep *ep,
gfp_t gfp_flags)
{
struct dwc2_request *req;
debug("%s: %s %p\n", __func__, ep->name, ep);
req = memalign(CONFIG_SYS_CACHELINE_SIZE, sizeof(*req));
if (!req)
return 0;
memset(req, 0, sizeof *req);
INIT_LIST_HEAD(&req->queue);
return &req->req;
}
static void dwc2_free_request(struct usb_ep *ep, struct usb_request *_req)
{
struct dwc2_request *req;
debug("%s: %p\n", __func__, ep);
req = container_of(_req, struct dwc2_request, req);
WARN_ON(!list_empty(&req->queue));
kfree(req);
}
/* dequeue JUST ONE request */
static int dwc2_dequeue(struct usb_ep *_ep, struct usb_request *_req)
{
struct dwc2_ep *ep;
struct dwc2_request *req;
unsigned long flags = 0;
debug("%s: %p\n", __func__, _ep);
ep = container_of(_ep, struct dwc2_ep, ep);
if (!_ep || ep->ep.name == ep0name)
return -EINVAL;
spin_lock_irqsave(&ep->dev->lock, flags);
/* make sure it's actually queued on this endpoint */
list_for_each_entry(req, &ep->queue, queue) {
if (&req->req == _req)
break;
}
if (&req->req != _req) {
spin_unlock_irqrestore(&ep->dev->lock, flags);
return -EINVAL;
}
done(ep, req, -ECONNRESET);
spin_unlock_irqrestore(&ep->dev->lock, flags);
return 0;
}
/*
* Return bytes in EP FIFO
*/
static int dwc2_fifo_status(struct usb_ep *_ep)
{
int count = 0;
struct dwc2_ep *ep;
ep = container_of(_ep, struct dwc2_ep, ep);
if (!_ep) {
debug("%s: bad ep\n", __func__);
return -ENODEV;
}
debug("%s: %d\n", __func__, ep_index(ep));
/* LPD can't report unclaimed bytes from IN fifos */
if (ep_is_in(ep))
return -EOPNOTSUPP;
return count;
}
/*
* Flush EP FIFO
*/
static void dwc2_fifo_flush(struct usb_ep *_ep)
{
struct dwc2_ep *ep;
ep = container_of(_ep, struct dwc2_ep, ep);
if (unlikely(!_ep || (!ep->desc && ep->ep.name != ep0name))) {
debug("%s: bad ep\n", __func__);
return;
}
debug("%s: %d\n", __func__, ep_index(ep));
}
static const struct usb_gadget_ops dwc2_udc_ops = {
/* current versions must always be self-powered */
};
static struct dwc2_udc memory = {
.usb_address = 0,
.gadget = {
.ops = &dwc2_udc_ops,
.ep0 = &memory.ep[0].ep,
.name = driver_name,
},
/* control endpoint */
.ep[0] = {
.ep = {
.name = ep0name,
.ops = &dwc2_ep_ops,
.maxpacket = EP0_FIFO_SIZE,
},
.dev = &memory,
.bEndpointAddress = 0,
.bmAttributes = 0,
.ep_type = ep_control,
},
/* first group of endpoints */
.ep[1] = {
.ep = {
.name = "ep1in-bulk",
.ops = &dwc2_ep_ops,
.maxpacket = EP_FIFO_SIZE,
},
.dev = &memory,
.bEndpointAddress = USB_DIR_IN | 1,
.bmAttributes = USB_ENDPOINT_XFER_BULK,
.ep_type = ep_bulk_out,
.fifo_num = 1,
},
.ep[2] = {
.ep = {
.name = "ep2out-bulk",
.ops = &dwc2_ep_ops,
.maxpacket = EP_FIFO_SIZE,
},
.dev = &memory,
.bEndpointAddress = USB_DIR_OUT | 2,
.bmAttributes = USB_ENDPOINT_XFER_BULK,
.ep_type = ep_bulk_in,
.fifo_num = 2,
},
.ep[3] = {
.ep = {
.name = "ep3in-int",
.ops = &dwc2_ep_ops,
.maxpacket = EP_FIFO_SIZE,
},
.dev = &memory,
.bEndpointAddress = USB_DIR_IN | 3,
.bmAttributes = USB_ENDPOINT_XFER_INT,
.ep_type = ep_interrupt,
.fifo_num = 3,
},
};
/*
* probe - binds to the platform device
*/
int dwc2_udc_probe(struct dwc2_plat_otg_data *pdata)
{
struct dwc2_udc *dev = &memory;
int retval = 0;
debug("%s: %p\n", __func__, pdata);
dev->pdata = pdata;
reg = (struct dwc2_usbotg_reg *)pdata->regs_otg;
/* regs_otg = (void *)pdata->regs_otg; */
dev->gadget.is_dualspeed = 1; /* Hack only*/
dev->gadget.is_otg = 0;
dev->gadget.is_a_peripheral = 0;
dev->gadget.b_hnp_enable = 0;
dev->gadget.a_hnp_support = 0;
dev->gadget.a_alt_hnp_support = 0;
the_controller = dev;
usb_ctrl = memalign(CONFIG_SYS_CACHELINE_SIZE,
ROUND(sizeof(struct usb_ctrlrequest),
CONFIG_SYS_CACHELINE_SIZE));
if (!usb_ctrl) {
pr_err("No memory available for UDC!\n");
return -ENOMEM;
}
usb_ctrl_dma_addr = (dma_addr_t) usb_ctrl;
udc_reinit(dev);
return retval;
}
int usb_gadget_handle_interrupts(int index)
{
u32 intr_status = readl(&reg->gintsts);
u32 gintmsk = readl(&reg->gintmsk);
if (intr_status & gintmsk)
return dwc2_udc_irq(1, (void *)the_controller);
return 0;
}