| menu "mpc8xx CPU" | |
| depends on MPC8xx | |
| config SYS_CPU | |
| default "mpc8xx" | |
| choice | |
| prompt "Target select" | |
| optional | |
| config TARGET_MCR3000 | |
| bool "Support MCR3000 board from CSSI" | |
| config TARGET_CMPC885 | |
| bool "Support CMPC885 board from CSSI" | |
| endchoice | |
| choice | |
| prompt "CPU select" | |
| default MPC866 | |
| config MPC866 | |
| bool "MPC866" | |
| select SYS_CACHE_SHIFT_4 | |
| config MPC885 | |
| bool "MPC885" | |
| select SYS_CACHE_SHIFT_4 | |
| endchoice | |
| choice | |
| prompt "Microcode patch selection" | |
| default NO_UCODE_PATCH | |
| help | |
| This allows loading of CPM microcode. | |
| Only one microcode can be loaded at a time. | |
| config NO_UCODE_PATCH | |
| bool "None" | |
| config USB_SOF_UCODE_PATCH | |
| bool "USB SOF patch" | |
| depends on MPC885 | |
| help | |
| This microcode fixes CPM15 errata: | |
| When the USB controller is configured in Host mode, and the | |
| SOF generation (SFTE=1 in USMOD register) is being used, | |
| there may be false CRC error indication in other SCCs. | |
| Although the data is received correctly, the CRC result | |
| will be corrupted. | |
| config SMC_UCODE_PATCH | |
| bool "SMC relocation patch" | |
| help | |
| This microcode relocates SMC1 and SMC2 parameter RAMs to allow | |
| extended parameter RAM for SCC3 and SCC4 (ex: for QMC mode) | |
| config SMC1_RPBASE | |
| hex "SMC1 relocation offset" | |
| depends on SMC_UCODE_PATCH | |
| default 0x1e80 | |
| help | |
| Offset of SMC1 parameter RAM to be written to RPBASE register. | |
| config SMC2_RPBASE | |
| hex "SMC2 relocation offset" | |
| depends on SMC_UCODE_PATCH | |
| default 0x1f80 | |
| help | |
| Offset of SMC2 parameter RAM to be written to RPBASE register. | |
| endchoice | |
| comment "Specific commands" | |
| config CMD_IMMAP | |
| bool "Enable various commands to dump IMMR information" | |
| help | |
| This enables various commands such as: | |
| siuinfo - print System Interface Unit (SIU) registers | |
| memcinfo - print Memory Controller registers | |
| comment "Configuration Registers" | |
| config SYS_SIUMCR | |
| hex "SIUMCR register" | |
| help | |
| SIU Module Configuration (11-6) | |
| config SYS_SYPCR | |
| hex "SYPCR register" if !WDT_MPC8xxx | |
| default 0x0 | |
| help | |
| System Protection Control (11-9) | |
| config SYS_TBSCR | |
| hex "TBSCR register" | |
| help | |
| Time Base Status and Control (11-26) | |
| config SYS_PISCR | |
| hex "PISCR register" | |
| help | |
| Periodic Interrupt Status and Control (11-31) | |
| config SYS_PLPRCR_BOOL | |
| bool "Customise PLPRCR" | |
| config SYS_PLPRCR | |
| hex "PLPRCR register" | |
| depends on SYS_PLPRCR_BOOL | |
| help | |
| PLL, Low-Power, and Reset Control Register (15-30) | |
| config SYS_SCCR | |
| hex "SCCR register" | |
| help | |
| System Clock and reset Control Register (15-27) | |
| config SYS_SCCR_MASK | |
| hex "MASK for setting SCCR register" | |
| config SYS_DER | |
| hex "DER register" | |
| help | |
| Debug Event Register (37-47) | |
| source "board/cssi/mcr3000/Kconfig" | |
| source "board/cssi/cmpc885/Kconfig" | |
| endmenu |