| Work_92105 from Work Microwave is an LPC3250- based board with the | |
| following features: | |
| - 64MB SDR DRAM | |
| - 1 GB SLC NAND, managed through MLC controller. | |
| - Ethernet | |
| - Ethernet + PHY SMSC8710 | |
| - I2C: | |
| - EEPROM (24M01-compatible) | |
| - RTC (DS1374-compatible) | |
| - Temperature sensor (DS620) | |
| - DACs (2 x MAX518) | |
| - SPI (through SSP interface) | |
| - Port expander MAX6957 | |
| - LCD display (HD44780-compatible), controlled | |
| through the port expander and DACs | |
| Standard SPL and U-Boot binaries | |
| -------------------------------- | |
| The default 'make' (or the 'make all') command will produce the | |
| following files: | |
| 1. spl/u-boot-spl.bin SPL, intended to run from SRAM at address 0. | |
| This file can be loaded in SRAM through a JTAG | |
| debugger or through the LPC32XX Service Boot | |
| mechanism. | |
| 2. u-boot.bin The raw U-Boot image, which can be loaded in | |
| DDR through a JTAG debugger (for instance by | |
| breaking SPL after DDR init), or by a running | |
| U-Boot through e.g. 'loady' or 'tftp' and then | |
| executed with 'go'. | |
| 3. u-boot.img A U-Boot image with a mkimage header prepended. | |
| SPL assumes (even when loaded through JTAG or | |
| Service Boot) that such an image will be found | |
| at offset 0x00040000 in NAND. | |
| NAND cold-boot binaries | |
| ----------------------- | |
| The board can boot entirely from power-on with only SPL and U-Boot in | |
| NAND. The LPC32XX-specific 'make lpc32xx-full.bin' command will produce | |
| (in addition to spl/u-boot-spl.bin and u-boot.img if they were not made | |
| already) the following files: | |
| 4. lpc32xx-spl.img spl/u-boot-spl.bin, with a LPC32XX boot header | |
| prepended. This header is required for the ROM | |
| code to load SPL into SRAM and branch into it. | |
| The content of this file is expected to reside | |
| in NAND at addresses 0x00000000 and 0x00020000 | |
| (two copies). | |
| 5. lpc32xx-boot-0.bin lpc32xx-spl.img, padded with 0xFF bytes to a | |
| size of 0x20000 bytes. This file covers exactly | |
| the reserved area for the first bootloader copy | |
| in NAND. | |
| 6. lpc32xx-boot-1.bin Same as lpc32xx-boot-0.bin. This is intended to | |
| be used as the second bootloader copy. | |
| 7. lpc32xx-full.bin lpc32xx-boot-0.bin, lpc32xx-boot-1.bin and | |
| u-boot.img concatenated. This file represents | |
| the content of whole bootloader as present in | |
| NAND at offset 00x00000000. | |
| Flashing instructions | |
| --------------------- | |
| The following assumes a working U-Boot on the target, with the ability | |
| to load files into DDR. | |
| To update the whole bootloader: | |
| nand erase 0x00000000 0x80000 | |
| (load lpc32xx-full.bin at location $loadaddr) | |
| nand write $loadaddr 0x00000000 $filesize | |
| To update SPL only (note the double nand write) : | |
| nand erase 0x00000000 0x40000 | |
| (load lpc32xx-spl.img or lpc32xx-boot-N.bin at location $loadaddr) | |
| nand write $loadaddr 0x00000000 $filesize | |
| nand write $loadaddr 0x00020000 $filesize | |
| To update U-Boot only: | |
| nand erase 0x00040000 0x40000 | |
| (load u-boot.img at location $loadaddr) | |
| nand write $loadaddr 0x00040000 $filesize |