| if TARGET_MICROBLAZE_GENERIC | |
| config SYS_BOARD | |
| default "microblaze-generic" | |
| config SYS_VENDOR | |
| default "xilinx" | |
| config XILINX_MICROBLAZE0_USE_MSR_INSTR | |
| int "USE_MSR_INSTR range (0:1)" | |
| default 0 | |
| config XILINX_MICROBLAZE0_USE_PCMP_INSTR | |
| int "USE_PCMP_INSTR range (0:1)" | |
| default 0 | |
| config XILINX_MICROBLAZE0_USE_BARREL | |
| int "USE_BARREL range (0:1)" | |
| default 0 | |
| config XILINX_MICROBLAZE0_USE_DIV | |
| int "USE_DIV range (0:1)" | |
| default 0 | |
| config XILINX_MICROBLAZE0_USE_HW_MUL | |
| int "USE_HW_MUL values (0=NONE, 1=MUL32, 2=MUL64)" | |
| default 0 | |
| config XILINX_MICROBLAZE0_HW_VER | |
| string "Core version number" | |
| default "7.10.d" | |
| config XILINX_MICROBLAZE0_FPGA_FAMILY | |
| string "Targeted FPGA family" | |
| default "virtex5" | |
| help | |
| This option contains info about the target FPGA architecture | |
| (Zynq-7000, UltraScale+ Kintex, etc) that the MicroBlaze soft core is | |
| implemented on. It corresponds to the C_FAMILY hdl parameter. | |
| config XILINX_MICROBLAZE0_USR_EXCEP | |
| bool "MicroBlaze user exception support" | |
| default y | |
| help | |
| Enable this option in order to install the user exception handler | |
| (_exception_handler routine from arch/microblaze/cpu/exception.c) in | |
| the exception vector table. The user exception vector is located at | |
| C_BASE_VECTORS + 0x8 address. | |
| config XILINX_MICROBLAZE0_DELAY_SLOT_EXCEP | |
| bool "MicroBlaze delay slot exception support" | |
| default y | |
| help | |
| Enable this option if the MicroBlaze processor supports exceptions | |
| caused by delay slot instructions (processor version >= v5.00). When | |
| enabled, the hw exception handler will print a message indicating | |
| whether the exception was triggered by a delay slot instruction. | |
| config XILINX_MICROBLAZE0_VECTOR_BASE_ADDR | |
| hex "Location of MicroBlaze vectors" | |
| default 0x0 | |
| help | |
| Memory address location of the exception vector table. It is | |
| configurable via the C_BASE_VECTORS hdl parameter. | |
| config XILINX_MICROBLAZE0_USE_WDC | |
| bool "MicroBlaze wdc instruction support" | |
| default y | |
| help | |
| Enable this option if the MicroBlaze processor is configured with | |
| support for the "wdc" (Write to Data Cache) instruction. | |
| config SPL_XILINX_MICROBLAZE0_USE_WDC | |
| bool | |
| default XILINX_MICROBLAZE0_USE_WDC | |
| config XILINX_MICROBLAZE0_USE_WIC | |
| bool "MicroBlaze wic instruction support" | |
| default y | |
| help | |
| Enable this option if the MicroBlaze processor is configured with | |
| support for the "wic" (Write to Instruction Cache) instruction. | |
| config SPL_XILINX_MICROBLAZE0_USE_WIC | |
| bool | |
| default XILINX_MICROBLAZE0_USE_WIC | |
| config XILINX_MICROBLAZE0_DCACHE_SIZE | |
| int "Default data cache size" | |
| default 32768 | |
| help | |
| This fallback size will be used when no dcache info can be found in | |
| the device tree, or when the data cache is flushed very early in the | |
| boot process, before device tree is available. | |
| config XILINX_MICROBLAZE0_ICACHE_SIZE | |
| int "Default instruction cache size" | |
| default 32768 | |
| help | |
| This fallback size will be used when no icache info can be found in | |
| the device tree, or when the instruction cache is flushed very early | |
| in the boot process, before device tree is available. | |
| config XILINX_MICROBLAZE0_PVR | |
| bool "MicroBlaze PVR support" | |
| help | |
| Enables helper functions and macros needed to manipulate PVR | |
| (Processor Version Register) data. Currently, only the microblaze | |
| UCLASS_CPU driver makes use of this feature to retrieve CPU info at | |
| runtime. | |
| endif |