| /* | |
| * | |
| * Copyright (C) 2015 Amlogic, Inc. All rights reserved. | |
| * | |
| * This program is free software; you can redistribute it and/or modify | |
| * it under the terms of the GNU General Public License as published by | |
| * the Free Software Foundation; either version 2 of the License, or | |
| * (at your option) any later version. | |
| * | |
| * This program is distributed in the hope that it will be useful, but WITHOUT | |
| * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or | |
| * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for | |
| * more details. | |
| * | |
| * You should have received a copy of the GNU General Public License along | |
| * with this program; if not, write to the Free Software Foundation, Inc., | |
| * 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301, USA. | |
| */ | |
| #include <common.h> | |
| #include <malloc.h> | |
| #include <errno.h> | |
| #include <environment.h> | |
| #include <fdt_support.h> | |
| #include <libfdt.h> | |
| #ifdef CONFIG_SYS_I2C_AML | |
| #include <aml_i2c.h> | |
| #include <asm/arch/secure_apb.h> | |
| #endif | |
| #include <amlogic/canvas.h> | |
| #ifdef CONFIG_AML_VPU | |
| #include <vpu.h> | |
| #endif | |
| #include <vpp.h> | |
| #ifdef CONFIG_AML_V2_FACTORY_BURN | |
| #include <amlogic/aml_v2_burning.h> | |
| #endif// #ifdef CONFIG_AML_V2_FACTORY_BURN | |
| #ifdef CONFIG_AML_HDMITX20 | |
| #include <amlogic/hdmi.h> | |
| #endif | |
| #include <asm/arch/eth_setup.h> | |
| #include <phy.h> | |
| #include <asm/cpu_id.h> | |
| DECLARE_GLOBAL_DATA_PTR; | |
| //new static eth setup | |
| struct eth_board_socket* eth_board_skt; | |
| int serial_set_pin_port(unsigned long port_base) | |
| { | |
| //UART in "Always On Module" | |
| //GPIOAO_0==tx,GPIOAO_1==rx | |
| //setbits_le32(P_AO_RTI_PIN_MUX_REG,3<<11); | |
| return 0; | |
| } | |
| int dram_init(void) | |
| { | |
| gd->ram_size = PHYS_SDRAM_1_SIZE; | |
| return 0; | |
| } | |
| /* secondary_boot_func | |
| * this function should be write with asm, here, is is only for compiling pass | |
| * */ | |
| void secondary_boot_func(void) | |
| { | |
| } | |
| void internalPhyConfig(struct phy_device *phydev) | |
| { | |
| /*Enable Analog and DSP register Bank access by*/ | |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x14, 0x0000); | |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x14, 0x0400); | |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x14, 0x0000); | |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x14, 0x0400); | |
| /*Write Analog register 23*/ | |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x17, 0x8E0D); | |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x14, 0x4417); | |
| /*Enable fractional PLL*/ | |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x17, 0x0005); | |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x14, 0x5C1B); | |
| //Programme fraction FR_PLL_DIV1 | |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x17, 0x029A); | |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x14, 0x5C1D); | |
| //## programme fraction FR_PLL_DiV1 | |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x17, 0xAAAA); | |
| phy_write(phydev, MDIO_DEVAD_NONE, 0x14, 0x5C1C); | |
| } | |
| static void setup_net_chip(void) | |
| { | |
| eth_aml_reg0_t eth_reg0; | |
| eth_reg0.d32 = 0; | |
| eth_reg0.b.phy_intf_sel = 0; | |
| eth_reg0.b.data_endian = 0; | |
| eth_reg0.b.desc_endian = 0; | |
| eth_reg0.b.rx_clk_rmii_invert = 0; | |
| eth_reg0.b.rgmii_tx_clk_src = 0; | |
| eth_reg0.b.rgmii_tx_clk_phase = 0; | |
| eth_reg0.b.rgmii_tx_clk_ratio = 0; | |
| eth_reg0.b.phy_ref_clk_enable = 0; | |
| eth_reg0.b.clk_rmii_i_invert = 1; | |
| eth_reg0.b.clk_en = 1; | |
| eth_reg0.b.adj_enable = 0; | |
| eth_reg0.b.adj_setup = 0; | |
| eth_reg0.b.adj_delay = 0; | |
| eth_reg0.b.adj_skew = 0; | |
| eth_reg0.b.cali_start = 0; | |
| eth_reg0.b.cali_rise = 0; | |
| eth_reg0.b.cali_sel = 0; | |
| eth_reg0.b.rgmii_rx_reuse = 0; | |
| eth_reg0.b.eth_urgent = 0; | |
| setbits_le32(P_PREG_ETH_REG0, eth_reg0.d32);// rmii mode | |
| *P_PREG_ETH_REG2 = 0x10110181; | |
| *P_PREG_ETH_REG3 = 0xe409087f; | |
| setbits_le32(HHI_GCLK_MPEG1,1<<3); | |
| /* power on memory */ | |
| clrbits_le32(HHI_MEM_PD_REG0, (1 << 3) | (1<<2)); | |
| } | |
| extern struct eth_board_socket* eth_board_setup(char *name); | |
| extern int designware_initialize(ulong base_addr, u32 interface); | |
| int board_eth_init(bd_t *bis) | |
| { | |
| setup_net_chip(); | |
| udelay(1000); | |
| designware_initialize(ETH_BASE, PHY_INTERFACE_MODE_RMII); | |
| return 0; | |
| } | |
| #if CONFIG_AML_SD_EMMC | |
| #include <mmc.h> | |
| #include <asm/arch/sd_emmc.h> | |
| static int sd_emmc_init(unsigned port) | |
| { | |
| switch (port) | |
| { | |
| case SDIO_PORT_A: | |
| break; | |
| case SDIO_PORT_B: | |
| //todo add card detect | |
| //setbits_le32(P_PREG_PAD_GPIO5_EN_N,1<<29);//CARD_6 | |
| break; | |
| case SDIO_PORT_C: | |
| //enable pull up | |
| //clrbits_le32(P_PAD_PULL_UP_REG3, 0xff<<0); | |
| break; | |
| default: | |
| break; | |
| } | |
| return cpu_sd_emmc_init(port); | |
| } | |
| extern unsigned sd_debug_board_1bit_flag; | |
| static int sd_emmc_detect(unsigned port) | |
| { | |
| int ret; | |
| switch (port) { | |
| case SDIO_PORT_A: | |
| break; | |
| case SDIO_PORT_B: | |
| setbits_le32(P_PREG_PAD_GPIO2_EN_N, 1 << 26);//CARD_6 | |
| ret = readl(P_PREG_PAD_GPIO2_I) & (1 << 26) ? 0 : 1; | |
| printf("%s\n", ret ? "card in" : "card out"); | |
| if ((readl(P_PERIPHS_PIN_MUX_6) & (3 << 8))) { //if uart pinmux set, debug board in | |
| if (!(readl(P_PREG_PAD_GPIO2_I) & (1 << 24))) { | |
| printf("sdio debug board detected, sd card with 1bit mode\n"); | |
| sd_debug_board_1bit_flag = 1; | |
| } else{ | |
| printf("sdio debug board detected, no sd card in\n"); | |
| sd_debug_board_1bit_flag = 0; | |
| return 1; | |
| } | |
| } | |
| break; | |
| default: | |
| break; | |
| } | |
| return 0; | |
| } | |
| static void sd_emmc_pwr_prepare(unsigned port) | |
| { | |
| cpu_sd_emmc_pwr_prepare(port); | |
| } | |
| static void sd_emmc_pwr_on(unsigned port) | |
| { | |
| switch (port) | |
| { | |
| case SDIO_PORT_A: | |
| break; | |
| case SDIO_PORT_B: | |
| // clrbits_le32(P_PREG_PAD_GPIO5_O,(1<<31)); //CARD_8 | |
| // clrbits_le32(P_PREG_PAD_GPIO5_EN_N,(1<<31)); | |
| /// @todo NOT FINISH | |
| break; | |
| case SDIO_PORT_C: | |
| break; | |
| default: | |
| break; | |
| } | |
| return; | |
| } | |
| static void sd_emmc_pwr_off(unsigned port) | |
| { | |
| /// @todo NOT FINISH | |
| switch (port) | |
| { | |
| case SDIO_PORT_A: | |
| break; | |
| case SDIO_PORT_B: | |
| // setbits_le32(P_PREG_PAD_GPIO5_O,(1<<31)); //CARD_8 | |
| // clrbits_le32(P_PREG_PAD_GPIO5_EN_N,(1<<31)); | |
| break; | |
| case SDIO_PORT_C: | |
| break; | |
| default: | |
| break; | |
| } | |
| return; | |
| } | |
| // #define CONFIG_TSD 1 | |
| static void board_mmc_register(unsigned port) | |
| { | |
| struct aml_card_sd_info *aml_priv=cpu_sd_emmc_get(port); | |
| if (aml_priv == NULL) | |
| return; | |
| aml_priv->sd_emmc_init=sd_emmc_init; | |
| aml_priv->sd_emmc_detect=sd_emmc_detect; | |
| aml_priv->sd_emmc_pwr_off=sd_emmc_pwr_off; | |
| aml_priv->sd_emmc_pwr_on=sd_emmc_pwr_on; | |
| aml_priv->sd_emmc_pwr_prepare=sd_emmc_pwr_prepare; | |
| aml_priv->desc_buf = malloc(NEWSD_MAX_DESC_MUN*(sizeof(struct sd_emmc_desc_info))); | |
| if (NULL == aml_priv->desc_buf) | |
| printf(" desc_buf Dma alloc Fail!\n"); | |
| else | |
| printf("aml_priv->desc_buf = 0x%p\n",aml_priv->desc_buf); | |
| sd_emmc_register(aml_priv); | |
| } | |
| int board_mmc_init(bd_t *bis) | |
| { | |
| #ifdef CONFIG_VLSI_EMULATOR | |
| //board_mmc_register(SDIO_PORT_A); | |
| #else | |
| //board_mmc_register(SDIO_PORT_B); | |
| #endif | |
| board_mmc_register(SDIO_PORT_B); | |
| board_mmc_register(SDIO_PORT_C); | |
| // board_mmc_register(SDIO_PORT_B1); | |
| return 0; | |
| } | |
| #ifdef CONFIG_SYS_I2C_AML | |
| #if 0 | |
| static void board_i2c_set_pinmux(void){ | |
| /*********************************************/ | |
| /* | I2C_Master_AO |I2C_Slave | */ | |
| /*********************************************/ | |
| /* | I2C_SCK | I2C_SCK_SLAVE | */ | |
| /* GPIOAO_4 | [AO_PIN_MUX: 6] | [AO_PIN_MUX: 2] | */ | |
| /*********************************************/ | |
| /* | I2C_SDA | I2C_SDA_SLAVE | */ | |
| /* GPIOAO_5 | [AO_PIN_MUX: 5] | [AO_PIN_MUX: 1] | */ | |
| /*********************************************/ | |
| //disable all other pins which share with I2C_SDA_AO & I2C_SCK_AO | |
| clrbits_le32(P_AO_RTI_PIN_MUX_REG, ((1<<2)|(1<<24)|(1<<1)|(1<<23))); | |
| //enable I2C MASTER AO pins | |
| setbits_le32(P_AO_RTI_PIN_MUX_REG, | |
| (MESON_I2C_MASTER_AO_GPIOAO_4_BIT | MESON_I2C_MASTER_AO_GPIOAO_5_BIT)); | |
| udelay(10); | |
| }; | |
| #endif | |
| struct aml_i2c_platform g_aml_i2c_plat = { | |
| .wait_count = 1000000, | |
| .wait_ack_interval = 5, | |
| .wait_read_interval = 5, | |
| .wait_xfer_interval = 5, | |
| .master_no = AML_I2C_MASTER_AO, | |
| .use_pio = 0, | |
| .master_i2c_speed = AML_I2C_SPPED_400K, | |
| .master_ao_pinmux = { | |
| .scl_reg = (unsigned long)MESON_I2C_MASTER_AO_GPIOAO_4_REG, | |
| .scl_bit = MESON_I2C_MASTER_AO_GPIOAO_4_BIT, | |
| .sda_reg = (unsigned long)MESON_I2C_MASTER_AO_GPIOAO_5_REG, | |
| .sda_bit = MESON_I2C_MASTER_AO_GPIOAO_5_BIT, | |
| } | |
| }; | |
| #if 0 | |
| static void board_i2c_init(void) | |
| { | |
| //set I2C pinmux with PCB board layout | |
| board_i2c_set_pinmux(); | |
| //Amlogic I2C controller initialized | |
| //note: it must be call before any I2C operation | |
| aml_i2c_init(); | |
| udelay(10); | |
| } | |
| #endif | |
| #endif | |
| #endif | |
| #if defined(CONFIG_BOARD_EARLY_INIT_F) | |
| int board_early_init_f(void){ | |
| /*add board early init function here*/ | |
| return 0; | |
| } | |
| #endif | |
| #ifdef CONFIG_USB_XHCI_AMLOGIC_GXL | |
| #include <asm/arch/usb-new.h> | |
| #include <asm/arch/gpio.h> | |
| #define CONFIG_GXL_USB_U2_PORT_NUM 3 | |
| #define CONFIG_GXL_USB_U3_PORT_NUM 0 | |
| struct amlogic_usb_config g_usb_config_GXL_skt={ | |
| CONFIG_GXL_XHCI_BASE, | |
| USB_ID_MODE_HARDWARE, | |
| NULL,//gpio_set_vbus_power, //set_vbus_power | |
| CONFIG_GXL_USB_PHY2_BASE, | |
| CONFIG_GXL_USB_PHY3_BASE, | |
| CONFIG_GXL_USB_U2_PORT_NUM, | |
| CONFIG_GXL_USB_U3_PORT_NUM, | |
| }; | |
| #endif /*CONFIG_USB_XHCI_AMLOGIC*/ | |
| #ifdef CONFIG_AML_HDMITX20 | |
| static void hdmi_tx_set_hdmi_5v(void) | |
| { | |
| /*Power on VCC_5V for HDMI_5V*/ | |
| clrbits_le32(P_PREG_PAD_GPIO1_EN_N, 1 << 23); | |
| clrbits_le32(P_PREG_PAD_GPIO1_O, 1 << 23); | |
| } | |
| #endif | |
| int board_init(void) | |
| { | |
| //Please keep CONFIG_AML_V2_FACTORY_BURN at first place of board_init | |
| #ifdef CONFIG_AML_V2_FACTORY_BURN | |
| aml_try_factory_usb_burning(0, gd->bd); | |
| #endif// #ifdef CONFIG_AML_V2_FACTORY_BURN | |
| /*for LED*/ | |
| //clear pinmux | |
| clrbits_le32(AO_RTI_PIN_MUX_REG, ((1<<3)|(1<<4))); | |
| clrbits_le32(AO_RTI_PIN_MUX_REG2, ((1<<1)|(1<<31))); | |
| //set output mode | |
| clrbits_le32(PREG_PAD_GPIO0_EN_N, (1 << 24)); | |
| //set output 1 | |
| setbits_le32(PREG_PAD_GPIO0_O, (1 << 24)); | |
| /*Power on GPIOAO_2 for VCC_5V*/ | |
| clrbits_le32(P_AO_GPIO_O_EN_N, ((1<<2)|(1<<18))); | |
| #ifdef CONFIG_USB_XHCI_AMLOGIC_GXL | |
| board_usb_init(&g_usb_config_GXL_skt,BOARD_USB_MODE_HOST); | |
| #endif /*CONFIG_USB_XHCI_AMLOGIC*/ | |
| canvas_init(); | |
| #ifndef CONFIG_AML_IRDETECT_EARLY | |
| #ifdef CONFIG_AML_HDMITX20 | |
| hdmi_tx_set_hdmi_5v(); | |
| hdmi_tx_init(); | |
| #endif | |
| #endif | |
| #ifdef CONFIG_AML_NAND | |
| extern int amlnf_init(unsigned char flag); | |
| amlnf_init(0); | |
| #endif | |
| return 0; | |
| } | |
| #ifdef CONFIG_AML_IRDETECT_EARLY | |
| #ifdef CONFIG_AML_HDMITX20 | |
| static int do_hdmi_init(cmd_tbl_t *cmdtp, int flag, int argc, char *const argv[]) | |
| { | |
| hdmi_tx_set_hdmi_5v(); | |
| hdmi_tx_init(); | |
| return 0; | |
| } | |
| U_BOOT_CMD(hdmi_init, CONFIG_SYS_MAXARGS, 0, do_hdmi_init, | |
| "HDMI_INIT sub-system", | |
| "hdmit init\n") | |
| #endif | |
| #endif | |
| #ifdef CONFIG_BOARD_LATE_INIT | |
| int board_late_init(void){ | |
| int ret; | |
| //update env before anyone using it | |
| run_command("get_rebootmode; echo reboot_mode=${reboot_mode}; "\ | |
| "if test ${reboot_mode} = factory_reset; then "\ | |
| "defenv_reserv aml_dt;setenv upgrade_step 2;save; fi;", 0); | |
| run_command("if itest ${upgrade_step} == 1; then "\ | |
| "defenv_reserv; setenv upgrade_step 2; saveenv; fi;", 0); | |
| /*add board late init function here*/ | |
| ret = run_command("store dtb read $dtb_mem_addr", 1); | |
| if (ret) { | |
| printf("%s(): [store dtb read $dtb_mem_addr] fail\n", __func__); | |
| #ifdef CONFIG_DTB_MEM_ADDR | |
| char cmd[64]; | |
| printf("load dtb to %x\n", CONFIG_DTB_MEM_ADDR); | |
| sprintf(cmd, "store dtb read %x", CONFIG_DTB_MEM_ADDR); | |
| ret = run_command(cmd, 1); | |
| if (ret) { | |
| printf("%s(): %s fail\n", __func__, cmd); | |
| } | |
| #endif | |
| } | |
| #ifdef CONFIG_AML_VPU | |
| vpu_probe(); | |
| #endif | |
| vpp_init(); | |
| #ifndef CONFIG_AML_IRDETECT_EARLY | |
| /* after */ | |
| run_command("cvbs init;hdmitx hpd", 0); | |
| run_command("vout output $outputmode", 0); | |
| #endif | |
| #ifdef CONFIG_AML_V2_FACTORY_BURN | |
| aml_try_factory_sdcard_burning(0, gd->bd); | |
| #endif// #ifdef CONFIG_AML_V2_FACTORY_BURN | |
| if (get_cpu_id().family_id == MESON_CPU_MAJOR_ID_GXL) { | |
| setenv("maxcpus","4"); | |
| setenv("device_product","p231"); | |
| } | |
| if (get_cpu_id().family_id == MESON_CPU_MAJOR_ID_GXM) { | |
| setenv("maxcpus","8"); | |
| setenv("device_product","q201"); | |
| } | |
| /* load uboot pq value */ | |
| vpp_pq_load(); | |
| return 0; | |
| } | |
| #endif | |
| phys_size_t get_effective_memsize(void) | |
| { | |
| // >>16 -> MB, <<20 -> real size, so >>16<<20 = <<4 | |
| #if defined(CONFIG_SYS_MEM_TOP_HIDE) | |
| return (((readl(AO_SEC_GP_CFG0)) & 0xFFFF0000) << 4) - CONFIG_SYS_MEM_TOP_HIDE; | |
| #else | |
| return (((readl(AO_SEC_GP_CFG0)) & 0xFFFF0000) << 4); | |
| #endif | |
| } | |
| #ifdef CONFIG_MULTI_DTB | |
| int checkhw(char * name) | |
| { | |
| unsigned int ddr_size=0; | |
| char loc_name[64] = {0}; | |
| int i; | |
| for (i=0; i<CONFIG_NR_DRAM_BANKS; i++) { | |
| ddr_size += gd->bd->bi_dram[i].size; | |
| } | |
| #if defined(CONFIG_SYS_MEM_TOP_HIDE) | |
| ddr_size += CONFIG_SYS_MEM_TOP_HIDE; | |
| #endif | |
| if (get_cpu_id().family_id == MESON_CPU_MAJOR_ID_GXM) { | |
| switch (ddr_size) { | |
| case 0x80000000: | |
| strcpy(loc_name, "gxm_q201_2g\0"); | |
| break; | |
| case 0x40000000: | |
| strcpy(loc_name, "gxm_q201_1g\0"); | |
| break; | |
| case 0x2000000: | |
| strcpy(loc_name, "gxm_q201_512m\0"); | |
| break; | |
| default: | |
| //printf("DDR size: 0x%x, multi-dt doesn't support\n", ddr_size); | |
| strcpy(loc_name, "gxm_q201_unsupport\0"); | |
| break; | |
| } | |
| } | |
| else { | |
| switch (ddr_size) { | |
| case 0x80000000: | |
| strcpy(loc_name, "gxl_p231_2g\0"); | |
| break; | |
| case 0x40000000: | |
| strcpy(loc_name, "gxl_p231_1g\0"); | |
| break; | |
| case 0x2000000: | |
| strcpy(loc_name, "gxl_p231_512m\0"); | |
| break; | |
| default: | |
| //printf("DDR size: 0x%x, multi-dt doesn't support\n", ddr_size); | |
| strcpy(loc_name, "gxl_p231_unsupport\0"); | |
| break; | |
| } | |
| } | |
| strcpy(name, loc_name); | |
| setenv("aml_dt", loc_name); | |
| return 0; | |
| } | |
| #endif | |
| const char * const _env_args_reserve_[] = | |
| { | |
| "aml_dt", | |
| "firstboot", | |
| NULL//Keep NULL be last to tell END | |
| }; |