| Overview | |
| -------- | |
| - BSC9131 is integrated device that targets Femto base station market. | |
| It combines Power Architecture e500v2 and DSP StarCore SC3850 core | |
| technologies with MAPLE-B2F baseband acceleration processing elements. | |
| - It's MAPLE disabled personality is called 9231. | |
| The BSC9131 SoC includes the following function and features: | |
| . Power Architecture subsystem including a e500 processor with 256-Kbyte shared | |
| L2 cache | |
| . StarCore SC3850 DSP subsystem with a 512-Kbyte private L2 cache | |
| . The Multi Accelerator Platform Engine for Femto BaseStation Baseband | |
| Processing (MAPLE-B2F) | |
| . A multi-standard baseband algorithm accelerator for Channel Decoding/Encoding, | |
| Fourier Transforms, UMTS chip rate processing, LTE UP/DL Channel processing, | |
| and CRC algorithms | |
| . Consists of accelerators for Convolution, Filtering, Turbo Encoding, | |
| Turbo Decoding, Viterbi decoding, Chiprate processing, and Matrix Inversion | |
| operations | |
| . DDR3/3L memory interface with 32-bit data width without ECC and 16-bit with | |
| ECC, up to 400-MHz clock/800 MHz data rate | |
| . Dedicated security engine featuring trusted boot | |
| . DMA controller | |
| . OCNDMA with four bidirectional channels | |
| . Interfaces | |
| . Two triple-speed Gigabit Ethernet controllers featuring network acceleration | |
| including IEEE 1588. v2 hardware support and virtualization (eTSEC) | |
| . eTSEC 1 supports RGMII/RMII | |
| . eTSEC 2 supports RGMII | |
| . High-speed USB 2.0 host and device controller with ULPI interface | |
| . Enhanced secure digital (SD/MMC) host controller (eSDHC) | |
| . Antenna interface controller (AIC), supporting three industry standard | |
| JESD207/three custom ADI RF interfaces (two dual port and one single port) | |
| and three MAXIM's MaxPHY serial interfaces | |
| . ADI lanes support both full duplex FDD support and half duplex TDD support | |
| . Universal Subscriber Identity Module (USIM) interface that facilitates | |
| communication to SIM cards or Eurochip pre-paid phone cards | |
| . TDM with one TDM port | |
| . Two DUART, four eSPI, and two I2C controllers | |
| . Integrated Flash memory controller (IFC) | |
| . TDM with 256 channels | |
| . GPIO | |
| . Sixteen 32-bit timers | |
| The e500 core subsystem within the Power Architecture consists of the following: | |
| . 32-Kbyte L1 instruction cache | |
| . 32-Kbyte L1 data cache | |
| . 256-Kbyte L2 cache/L2 memory/L2 stash | |
| . programmable interrupt controller (PIC) | |
| . Debug support | |
| . Timers | |
| The SC3850 core subsystem consists of the following: | |
| . 32 Kbyte 8-way level 1 instruction cache (L1 ICache) | |
| . 32 Kbyte 8-way level 1 data cache (L1 DCache) | |
| . 512 Kbyte 8-way level 2 unified instruction/data cache (M2 memory) | |
| . Memory management unit (MMU) | |
| . Enhanced programmable interrupt controller (EPIC) | |
| . Debug and profiling unit (DPU) | |
| . Two 32-bit timers | |
| BSC9131RDB board Overview | |
| ------------------------- | |
| 1Gbyte DDR3 (on board DDR) | |
| 128Mbyte 2K page size NAND Flash | |
| 256 Kbit M24256 I2C EEPROM | |
| 128 Mbit SPI Flash memory | |
| USB-ULPI | |
| eTSEC1: Connected to RGMII PHY | |
| eTSEC2: Connected to RGMII PHY | |
| DUART interface: supports one UARTs up to 115200 bps for console display | |
| USIM connector | |
| Frequency Combinations Supported | |
| -------------------------------- | |
| Core MHz/CCB MHz/DDR(MT/s) | |
| 1. 1000/500/800 | |
| 2. 800/400/667 | |
| Boot Methods Supported | |
| ----------------------- | |
| 1. NAND Flash | |
| 2. SPI Flash | |
| Default Boot Method | |
| -------------------- | |
| NAND boot | |
| Building U-boot | |
| -------------- | |
| To build the u-boot for BSC9131RDB: | |
| 1. NAND Flash with sysclk 66MHz(J16 on RDB closed, default) | |
| make BSC9131RDB_NAND | |
| 2. NAND Flash with sysclk 100MHz(J16 on RDB open) | |
| make BSC9131RDB_NAND_SYSCLK100 | |
| 3. SPI Flash with sysclk 66MHz(J16 on RDB closed, default) | |
| make BSC9131RDB_SPIFLASH | |
| 4. SPI Flash with sysclk 100MHz(J16 on RDB open) | |
| make BSC9131RDB_SPIFLASH_SYSCLK100 | |
| Memory map | |
| ----------- | |
| 0x0000_0000 0x7FFF_FFFF DDR 1G cacheable | |
| 0xA0000000 0xBFFFFFFF Shared DSP core L2/M2 space 512M | |
| 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M | |
| 0xC1F0_0000 0xC1F3_FFFF PA SRAM Region 0 256K | |
| 0xC1F8_0000 0xC1F9_FFFF PA SRAM Region 1 128K | |
| 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K | |
| 0xFEE0_0000 0xFEE0_0FFF DSP Boot ROM 4K | |
| 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M | |
| 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M | |
| 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND Buffer 8M | |
| DDR Memory map | |
| --------------- | |
| 0x0000_0000 0x36FF_FFFF Memory passed onto Linux | |
| 0x3700_0000 0x37FF_FFFF PowerPC-DSP shared control area | |
| 0x3800_0000 0x4FFF_FFFF DSP Private area | |
| Out of 880M, passed onto Linux, 1hugetlb page of 256M is reserved for | |
| data communcation between PowerPC and DSP core. | |
| Rest is PowerPC private area. | |
| Flashing Images | |
| --------------- | |
| To place a new u-boot image in the NAND flash and then boot | |
| with that new image temporarily, use this: | |
| tftp 1000000 u-boot-nand.bin | |
| nand erase 0 100000 | |
| nand write 1000000 0 100000 | |
| reset | |
| Using the Device Tree Source File | |
| --------------------------------- | |
| To create the DTB (Device Tree Binary) image file, | |
| use a command similar to this: | |
| dtc -b 0 -f -I dts -O dtb bsc9131rdb.dts > bsc9131rdb.dtb | |
| Likely, that .dts file will come from here; | |
| linux-2.6/arch/powerpc/boot/dts/bsc9131rdb.dts | |
| Booting Linux | |
| ------------- | |
| Place a linux uImage in the TFTP disk area. | |
| tftp 1000000 uImage | |
| tftp 2000000 rootfs.ext2.gz.uboot | |
| tftp c00000 bsc9131rdb.dtb | |
| bootm 1000000 2000000 c00000 |