| Overview | |
| -------- | |
| The BSC9132 is a highly integrated device that targets the evolving | |
| Microcell, Picocell, and Enterprise-Femto base station market subsegments. | |
| The BSC9132 device combines Power Architecture e500 and DSP StarCore SC3850 | |
| core technologies with MAPLE-B2P baseband acceleration processing elements | |
| to address the need for a high performance, low cost, integrated solution | |
| that handles all required processing layers without the need for an | |
| external device except for an RF transceiver or, in a Micro base station | |
| configuration, a host device that handles the L3/L4 and handover between | |
| sectors. | |
| The BSC9132 SoC includes the following function and features: | |
| - Power Architecture subsystem including two e500 processors with | |
| 512-Kbyte shared L2 cache | |
| - Two StarCore SC3850 DSP subsystems, each with a 512-Kbyte private L2 | |
| cache | |
| - 32 Kbyte of shared M3 memory | |
| - The Multi Accelerator Platform Engine for Pico BaseStation Baseband | |
| Processing (MAPLE-B2P) | |
| - Two DDR3/3L memory interfaces with 32-bit data width (40 bits including | |
| ECC), up to 1333 MHz data rate | |
| - Dedicated security engine featuring trusted boot | |
| - Two DMA controllers | |
| - OCNDMA with four bidirectional channels | |
| - SysDMA with sixteen bidirectional channels | |
| - Interfaces | |
| - Four-lane SerDes PHY | |
| - PCI Express controller complies with the PEX Specification-Rev 2.0 | |
| - Two Common Public Radio Interface (CPRI) controller lanes | |
| - High-speed USB 2.0 host and device controller with ULPI interface | |
| - Enhanced secure digital (SD/MMC) host controller (eSDHC) | |
| - Antenna interface controller (AIC), supporting four industry | |
| standard JESD207/four custom ADI RF interfaces | |
| - ADI lanes support both full duplex FDD support & half duplex TDD | |
| - Universal Subscriber Identity Module (USIM) interface that | |
| facilitates communication to SIM cards or Eurochip pre-paid phone | |
| cards | |
| - Two DUART, two eSPI, and two I2C controllers | |
| - Integrated Flash memory controller (IFC) | |
| - GPIO | |
| - Sixteen 32-bit timers | |
| The SC3850 core subsystem consists of the following: | |
| - 32 KB, 8-way, level 1 instruction cache (L1 ICache) | |
| - 32 KB, 8-way, level 1 data cache (L1 DCache) | |
| - 512 KB, 8-way, level 2 unified instruction/data cache (L2 cache/M2 memory) | |
| - Memory management unit (MMU) | |
| - Global interrupt controller ( GIC) | |
| - Debug and profiling unit (DPU) | |
| - Two 32-bit quad timers | |
| BSC9132QDS board Overview | |
| ------------------------- | |
| 2Gbyte DDR3 (on board DDR), Dual Ranki | |
| 32Mbyte 16bit NOR flash | |
| 128Mbyte 2K page size NAND Flash | |
| 256 Kbit M24256 I2C EEPROM | |
| 128 Mbit SPI Flash memory | |
| SD slot | |
| USB-ULPI | |
| eTSEC1: Connected to SGMII PHY | |
| eTSEC2: Connected to SGMII PHY | |
| PCIe | |
| CPRI | |
| SerDes | |
| I2C RTC | |
| DUART interface: supports one UARTs up to 115200 bps for console display | |
| Frequency Combinations Supported | |
| -------------------------------- | |
| Core MHz/CCB MHz/DDR(MT/s) | |
| 1. CPU0/CPU1/CCB/DDR: 1000MHz/1000MHz/500MHz/800MHz | |
| (SYSCLK = 100MHz, DDRCLK = 100MHz) | |
| 2. CPU0/CPU1/CCB/DDR: 1200MHz/1200MHz/600MHz/1330MHz | |
| (SYSCLK = 100MHz, DDRCLK = 133MHz) | |
| Boot Methods Supported | |
| ----------------------- | |
| 1. NOR Flash | |
| 2. NAND Flash | |
| 3. SD Card | |
| 4. SPI flash | |
| Default Boot Method | |
| -------------------- | |
| NOR boot | |
| Building U-boot | |
| -------------- | |
| To build the u-boot for BSC9132QDS: | |
| 1. NOR Flash | |
| make BSC9132QDS_NOR_DDRCLK100 : For 100MHZ DDR CLK | |
| make BSC9132QDS_NOR_DDRCLK133 : For 133MHZ DDR CLK | |
| 2. NAND Flash : It is currently not supported | |
| 3. SPI Flash | |
| make BSC9132QDS_SPIFLASH_DDRCLK100 : For 100MHZ DDR CLK | |
| make BSC9132QDS_SPIFLASH_DDRCLK133 : For 133MHZ DDR CLK | |
| 4. SD Card | |
| make BSC9132QDS_SDCARD_DDRCLK100 : For 100MHZ DDR CLK | |
| make BSC9132QDS_SDCARD_DDRCLK133 : For 133MHZ DDR CLK | |
| Memory map | |
| ----------- | |
| 0x0000_0000 0x7FFF_FFFF DDR 2G cacheable | |
| 0x8000_0000 0x8FFF_FFFF NOR Flash 256M | |
| 0x9000_0000 0x9FFF_FFFF PCIe Memory 256M | |
| 0xA000_0000 0xA7FF_FFFF DSP core1 L2 space 128M | |
| 0xB000_0000 0xB0FF_FFFF DSP core0 M2 space 16M | |
| 0xB100_0000 0xB1FF_FFFF DSP core1 M2 space 16M | |
| 0xC000_0000 0xC000_7FFF M3 Memory 32K | |
| 0xC001_0000 0xC001_FFFF PCI Express I/O 64K | |
| 0xC100_0000 0xC13F_FFFF MAPLE-2F 4M | |
| 0xC1F0_0000 0xC1F7_FFFF PA SRAM Region 0 512K | |
| 0xC1F8_0000 0xC1FB_FFFF PA SRAM Region 1 512K | |
| 0xFED0_0000 0xFED0_3FFF SEC Secured RAM 16K | |
| 0xFEE0_0000 0xFEE0_0FFF DSP Boot ROM 4K | |
| 0xFF60_0000 0xFF6F_FFFF DSP CCSR 1M | |
| 0xFF70_0000 0xFF7F_FFFF PA CCSR 1M | |
| 0xFF80_0000 0xFFFF_FFFF Boot Page & NAND Buffer 8M | |
| Flashing Images | |
| --------------- | |
| To place a new u-boot image in the NAND flash and then boot | |
| with that new image temporarily, use this: | |
| tftp 1000000 u-boot-nand.bin | |
| nand erase 0 100000 | |
| nand write 1000000 0 100000 | |
| reset | |
| Using the Device Tree Source File | |
| --------------------------------- | |
| To create the DTB (Device Tree Binary) image file, | |
| use a command similar to this: | |
| dtc -b 0 -f -I dts -O dtb bsc9132qds.dts > bsc9132qds.dtb | |
| Likely, that .dts file will come from here; | |
| linux-2.6/arch/powerpc/boot/dts/bsc9132qds.dts | |
| Booting Linux | |
| ------------- | |
| Place a linux uImage in the TFTP disk area. | |
| tftp 1000000 uImage | |
| tftp 2000000 rootfs.ext2.gz.uboot | |
| tftp c00000 bsc9132qds.dtb | |
| bootm 1000000 2000000 c00000 |