| Overview | |
| -------- | |
| The T1040RDB is a Freescale reference board that hosts the T1040 SoC | |
| (and variants). Variants inclued T1042 presonality of T1040, in which | |
| case T1040RDB can also be called T1042RDB. | |
| The T1042RDB is a Freescale reference board that hosts the T1042 SoC | |
| (and variants). The board is similar to T1040RDB, T1040 is a reduced | |
| personality of T1040 SoC without Integrated 8-port Gigabit(L2 Switch). | |
| The T1042RDB_PI is a Freescale reference board that hosts the T1042 SoC. | |
| (a personality of T1040 SoC). The board is similar to T1040RDB but is | |
| designed specially with low power features targeted for Printing Image Market. | |
| Basic difference's among T1040RDB, T1042RDB_PI, T1042RDB | |
| ------------------------------------------------------------------------- | |
| Board Si Protocol Targeted Market | |
| ------------------------------------------------------------------------- | |
| T1040RDB T1040 0x66 Networking | |
| T1040RDB T1042 0x86 Networking | |
| T1042RDB_PI T1042 0x06 Printing & Imaging | |
| T1040 SoC Overview | |
| ------------------ | |
| The QorIQ T1040/T1042 processor support four integrated 64-bit e5500 PA | |
| processor cores with high-performance data path acceleration architecture | |
| and network peripheral interfaces required for networking & telecommunications. | |
| The T1040/T1042 SoC includes the following function and features: | |
| - Four e5500 cores, each with a private 256 KB L2 cache | |
| - 256 KB shared L3 CoreNet platform cache (CPC) | |
| - Interconnect CoreNet platform | |
| - 32-/64-bit DDR3L/DDR4 SDRAM memory controller with ECC and interleaving | |
| support | |
| - Data Path Acceleration Architecture (DPAA) incorporating acceleration | |
| for the following functions: | |
| - Packet parsing, classification, and distribution | |
| - Queue management for scheduling, packet sequencing, and congestion | |
| management | |
| - Cryptography Acceleration (SEC 5.0) | |
| - RegEx Pattern Matching Acceleration (PME 2.2) | |
| - IEEE Std 1588 support | |
| - Hardware buffer management for buffer allocation and deallocation | |
| - Ethernet interfaces | |
| - Integrated 8-port Gigabit Ethernet switch (T1040 only) | |
| - Four 1 Gbps Ethernet controllers | |
| - Two RGMII interfaces or one RGMII and one MII interfaces | |
| - High speed peripheral interfaces | |
| - Four PCI Express 2.0 controllers running at up to 5 GHz | |
| - Two SATA controllers supporting 1.5 and 3.0 Gb/s operation | |
| - Upto two QSGMII interface | |
| - Upto six SGMII interface supporting 1000 Mbps | |
| - One SGMII interface supporting upto 2500 Mbps | |
| - Additional peripheral interfaces | |
| - Two USB 2.0 controllers with integrated PHY | |
| - SD/eSDHC/eMMC | |
| - eSPI controller | |
| - Four I2C controllers | |
| - Four UARTs | |
| - Four GPIO controllers | |
| - Integrated flash controller (IFC) | |
| - LCD and HDMI interface (DIU) with 12 bit dual data rate | |
| - TDM interface | |
| - Multicore programmable interrupt controller (PIC) | |
| - Two 8-channel DMA engines | |
| - Single source clocking implementation | |
| - Deep Sleep power implementaion (wakeup from GPIO/Timer/Ethernet/USB) | |
| T1040 SoC Personalities | |
| ------------------------- | |
| T1022 Personality: | |
| T1022 is a reduced personality of T1040 with less core/clusters. | |
| T1042 Personality: | |
| T1042 is a reduced personality of T1040 without Integrated 8-port Gigabit | |
| Ethernet switch. Rest of the blocks are same as T1040 | |
| T1040RDB board Overview | |
| ------------------------- | |
| - SERDES Connections, 8 lanes information: | |
| 1: None | |
| 2: SGMII | |
| 3: QSGMII | |
| 4: QSGMII | |
| 5: PCIe1 x1 slot | |
| 6: mini PCIe connector | |
| 7: mini PCIe connector | |
| 8: SATA connector | |
| - DDR Controller | |
| - Supports rates of up to 1600 MHz data-rate | |
| - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types. | |
| - IFC/Local Bus | |
| - NAND flash: 1GB 8-bit NAND flash | |
| - NOR: 128MB 16-bit NOR Flash | |
| - Ethernet | |
| - Two on-board RGMII 10/100/1G ethernet ports. | |
| - CPLD | |
| - Clocks | |
| - System and DDR clock (SYSCLK, “DDRCLK”) | |
| - SERDES clocks | |
| - Power Supplies | |
| - USB | |
| - Supports two USB 2.0 ports with integrated PHYs | |
| - Two type A ports with 5V@1.5A per port. | |
| - SDHC | |
| - SDHC/SDXC connector | |
| - SPI | |
| - On-board 64MB SPI flash | |
| - Other IO | |
| - Two Serial ports | |
| - Four I2C ports | |
| T1042RDB_PI board Overview | |
| ------------------------- | |
| - SERDES Connections, 8 lanes information: | |
| 1, 2, 3, 4 : PCIe x4 slot | |
| 5: mini PCIe connector | |
| 6: mini PCIe connector | |
| 7: NA | |
| 8: SATA connector | |
| - DDR Controller | |
| - Supports rates of up to 1600 MHz data-rate | |
| - Supports one DDR3LP UDIMM/RDIMMs, of single-, dual- or quad-rank types. | |
| - IFC/Local Bus | |
| - NAND flash: 1GB 8-bit NAND flash | |
| - NOR: 128MB 16-bit NOR Flash | |
| - Ethernet | |
| - Two on-board RGMII 10/100/1G ethernet ports. | |
| - CPLD | |
| - Clocks | |
| - System and DDR clock (SYSCLK, “DDRCLK”) | |
| - SERDES clocks | |
| - Video | |
| - DIU supports video at up to 1280x1024x32bpp | |
| - Power Supplies | |
| - USB | |
| - Supports two USB 2.0 ports with integrated PHYs | |
| - Two type A ports with 5V@1.5A per port. | |
| - SDHC | |
| - SDHC/SDXC connector | |
| - SPI | |
| - On-board 64MB SPI flash | |
| - Other IO | |
| - Two Serial ports | |
| - Four I2C ports | |
| Memory map | |
| ----------- | |
| The addresses in brackets are physical addresses. | |
| Start Address End Address Description Size | |
| 0xF_FFDF_0000 0xF_FFDF_0FFF IFC - CPLD 4KB | |
| 0xF_FF80_0000 0xF_FF80_FFFF IFC - NAND Flash 64KB | |
| 0xF_FE00_0000 0xF_FEFF_FFFF CCSRBAR 16MB | |
| 0xF_F803_0000 0xF_F803_FFFF PCI Express 4 I/O Space 64KB | |
| 0xF_F802_0000 0xF_F802_FFFF PCI Express 3 I/O Space 64KB | |
| 0xF_F801_0000 0xF_F801_FFFF PCI Express 2 I/O Space 64KB | |
| 0xF_F800_0000 0xF_F800_FFFF PCI Express 1 I/O Space 64KB | |
| 0xF_F600_0000 0xF_F7FF_FFFF Queue manager software portal 32MB | |
| 0xF_F400_0000 0xF_F5FF_FFFF Buffer manager software portal 32MB | |
| 0xF_E800_0000 0xF_EFFF_FFFF IFC - NOR Flash 128MB | |
| 0xF_0000_0000 0xF_003F_FFFF DCSR 4MB | |
| 0xC_3000_0000 0xC_3FFF_FFFF PCI Express 4 Mem Space 256MB | |
| 0xC_2000_0000 0xC_2FFF_FFFF PCI Express 3 Mem Space 256MB | |
| 0xC_1000_0000 0xC_1FFF_FFFF PCI Express 2 Mem Space 256MB | |
| 0xC_0000_0000 0xC_0FFF_FFFF PCI Express 1 Mem Space 256MB | |
| 0x0_0000_0000 0x0_ffff_ffff DDR 2GB | |
| NOR Flash memory Map | |
| --------------------- | |
| Start End Definition Size | |
| 0xEFF40000 0xEFFFFFFF u-boot (current bank) 768KB | |
| 0xEFF20000 0xEFF3FFFF u-boot env (current bank) 128KB | |
| 0xEFF00000 0xEFF1FFFF FMAN Ucode (current bank) 128KB | |
| 0xED300000 0xEFEFFFFF rootfs (alt bank) 44MB | |
| 0xEC800000 0xEC8FFFFF Hardware device tree (alt bank) 1MB | |
| 0xEC020000 0xEC7FFFFF Linux.uImage (alt bank) 7MB + 875KB | |
| 0xEC000000 0xEC01FFFF RCW (alt bank) 128KB | |
| 0xEBF40000 0xEBFFFFFF u-boot (alt bank) 768KB | |
| 0xEBF20000 0xEBF3FFFF u-boot env (alt bank) 128KB | |
| 0xEBF00000 0xEBF1FFFF FMAN ucode (alt bank) 128KB | |
| 0xE9300000 0xEBEFFFFF rootfs (current bank) 44MB | |
| 0xE8800000 0xE88FFFFF Hardware device tree (cur bank) 11MB + 512KB | |
| 0xE8020000 0xE86FFFFF Linux.uImage (current bank) 7MB + 875KB | |
| 0xE8000000 0xE801FFFF RCW (current bank) 128KB | |
| Various Software configurations/environment variables/commands | |
| -------------------------------------------------------------- | |
| The below commands apply to the board | |
| 1. U-boot environment variable hwconfig | |
| The default hwconfig is: | |
| hwconfig=fsl_ddr:ctlr_intlv=null,bank_intlv=cs0_cs1;usb1: | |
| dr_mode=host,phy_type=utmi | |
| Note: For USB gadget set "dr_mode=peripheral" | |
| 2. FMAN Ucode versions | |
| fsl_fman_ucode_t1040.bin | |
| 3. Switching to alternate bank | |
| Commands for switching to alternate bank. | |
| 1. To change from vbank0 to vbank4 | |
| => cpld reset altbank (it will boot using vbank4) | |
| 2.To change from vbank4 to vbank0 | |
| => cpld reset (it will boot using vbank0) | |
| NAND boot with 2 Stage boot loader | |
| ---------------------------------- | |
| PBL initialise the internal SRAM and copy SPL(160KB) in SRAM. | |
| SPL further initialise DDR using SPD and environment variables and copy | |
| u-boot(768 KB) from flash to DDR. | |
| Finally SPL transer control to u-boot for futher booting. | |
| SPL has following features: | |
| - Executes within 256K | |
| - No relocation required | |
| Run time view of SPL framework during boot :- | |
| ----------------------------------------------- | |
| Area | Address | | |
| ----------------------------------------------- | |
| Secure boot | 0xFFFC0000 (32KB) | | |
| headers | | | |
| ----------------------------------------------- | |
| GD, BD | 0xFFFC8000 (4KB) | | |
| ----------------------------------------------- | |
| ENV | 0xFFFC9000 (8KB) | | |
| ----------------------------------------------- | |
| HEAP | 0xFFFCB000 (30KB) | | |
| ----------------------------------------------- | |
| STACK | 0xFFFD8000 (22KB) | | |
| ----------------------------------------------- | |
| U-boot SPL | 0xFFFD8000 (160KB) | | |
| ----------------------------------------------- | |
| NAND Flash memory Map on T104xRDB | |
| ------------------------------------------ | |
| Start End Definition Size | |
| 0x000000 0x0FFFFF u-boot 1MB | |
| 0x180000 0x19FFFF u-boot env 128KB | |
| 0x280000 0x29FFFF FMAN Ucode 128KB | |
| 0x380000 0x39FFFF QE Firmware 128KB | |
| SD Card memory Map on T104xRDB | |
| ------------------------------------------ | |
| Block #blocks Definition Size | |
| 0x008 2048 u-boot 1MB | |
| 0x800 0024 u-boot env 8KB | |
| 0x820 0256 FMAN Ucode 128KB | |
| 0x920 0256 QE Firmware 128KB | |
| SPI Flash memory Map on T104xRDB | |
| ------------------------------------------ | |
| Start End Definition Size | |
| 0x000000 0x0FFFFF u-boot 1MB | |
| 0x100000 0x101FFF u-boot env 8KB | |
| 0x110000 0x12FFFF FMAN Ucode 128KB | |
| 0x130000 0x14FFFF QE Firmware 128KB | |
| Please note QE Firmware is only valid for T1040RDB | |
| Switch Settings: (ON is 0, OFF is 1) | |
| =============== | |
| NAND boot SW setting: | |
| SW1: 10001000 | |
| SW2: 00111011 | |
| SW3: 11110001 | |
| SPI boot SW setting: | |
| SW1: 00100010 | |
| SW2: 10111011 | |
| SW3: 11100001 | |
| SD boot SW setting: | |
| SW1: 00100000 | |
| SW2: 00111011 | |
| SW3: 11100001 |