| /* |
| * (C) Copyright 2010-2012 |
| * NVIDIA Corporation <www.nvidia.com> |
| * |
| * SPDX-License-Identifier: GPL-2.0+ |
| */ |
| |
| #include <common.h> |
| #include <dm.h> |
| #include <asm/io.h> |
| #include <asm/arch/tegra.h> |
| #include <asm/arch/clock.h> |
| #include <asm/arch/funcmux.h> |
| #include <asm/arch/pinmux.h> |
| #include <asm/gpio.h> |
| #include <i2c.h> |
| |
| #ifdef CONFIG_TEGRA_MMC |
| /* |
| * Routine: pin_mux_mmc |
| * Description: setup the pin muxes/tristate values for the SDMMC(s) |
| */ |
| void pin_mux_mmc(void) |
| { |
| struct udevice *dev; |
| uchar val; |
| int ret; |
| |
| /* Turn on MAX8907B LDO12 to 2.8V for J40 power */ |
| ret = i2c_get_chip_for_busnum(0, 0x3c, &dev); |
| if (ret) { |
| printf("%s: Cannot find MAX8907B I2C chip\n", __func__); |
| return; |
| } |
| val = 0x29; |
| ret = i2c_write(dev, 0x46, &val, 1); |
| if (ret) |
| printf("i2c_write 0 0x3c 0x46 failed: %d\n", ret); |
| val = 0x00; |
| ret = i2c_write(dev, 0x45, &val, 1); |
| if (ret) |
| printf("i2c_write 0 0x3c 0x45 failed: %d\n", ret); |
| val = 0x1f; |
| ret = i2c_write(dev, 0x44, &val, 1); |
| if (ret) |
| printf("i2c_write 0 0x3c 0x44 failed: %d\n", ret); |
| |
| funcmux_select(PERIPH_ID_SDMMC3, FUNCMUX_SDMMC3_SDB_SLXA_8BIT); |
| funcmux_select(PERIPH_ID_SDMMC4, FUNCMUX_SDMMC4_ATC_ATD_8BIT); |
| } |
| #endif |
| |
| /* this is a weak define that we are overriding */ |
| void pin_mux_usb(void) |
| { |
| struct udevice *dev; |
| uchar val; |
| int ret; |
| |
| /* |
| * This is a hack. This should be represented in DT using the |
| * vbus-gpio property. However, U-Boot's DT support doesn't |
| * support any GPIO controller other than the Tegra's yet. |
| */ |
| |
| /* Turn on TAC6416's GPIO 0+1 for USB1/3's VBUS */ |
| ret = i2c_get_chip_for_busnum(0, 0x20, &dev); |
| if (ret) { |
| printf("%s: Cannot find TAC6416 I2C chip\n", __func__); |
| return; |
| } |
| val = 0x03; |
| ret = i2c_write(dev, 2, &val, 1); |
| if (ret) |
| printf("i2c_write 0 0x20 2 failed: %d\n", ret); |
| val = 0xfc; |
| ret = i2c_write(dev, 6, &val, 1); |
| if (ret) |
| printf("i2c_write 0 0x20 6 failed: %d\n", ret); |
| } |